106971-1172 ZEXEL 9 400 618 676 BOSCH INJECTION-PUMP ASSEMBLY 9400618676 1069711172 1156031732

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 618 676 9400618676

ZEXEL 106971-1172 1069711172

ISUZU 1156031732 1156031732

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106971-1172 zexel genuine, new aftermarket engine parts with delivery

Service parts 106971-1172 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106091-9110

3. GOVERNOR 105923-2790

4. SUPPLY PUMP 105237-5280

5. AUTOM. ADVANCE MECHANIS 105693-0540

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-7750

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 15.7(160)/22.1(225)

13. NOZZLE-HOLDER 105030-3540

14. NOZZLE 105025-0090

15. NOZZLE SET

Include in #1:

106971-1172 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 618 676 9400618676

ZEXEL 106971-1172 1069711172

ISUZU 1156031732 1156031732

Zexel num

Bosch num

Firm num

Name

106971-1172

9 400 618 676

1156031732 ISUZU

INJECTION-PUMP ASSEMBLY
12PE1-C K 14CC INJECTION PUMP ASSY PE12P PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-4320

Overflow valve opening pressure kPa 255 255 255

Overflow valve opening pressure kgf/cm2 2.6 2.6 2.6

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-9-8- 5-2-11-1 0-3-6-7-

Pre-stroke mm 5.5 5.47 5.53

Rack position
Point A R=A

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-4 deg. 15 14.75 15.25

Difference between angles 2
Cal 1-9 deg. 60 59.75 60.25

Difference between angles 3
Cal 1-8 deg. 75 74.75 75.25

Difference between angles 4
Cal 1-5 deg. 120 119.75 120.25

Difference between angles 5
Cyl.1-2 deg. 135 134.75 135.25

Difference between angles 6
Cal 1-11 deg. 180 179.75 180.25

Difference between angles 7
Cal 1-10 deg. 195 194.75 195.25

Difference between angles 8
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 9
Cal 1-6 deg. 255 254.75 255.25

Difference between angles 10
Cal 1-7 deg. 300 299.75 300.25

Difference between angles 11
Cal 1-12 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point -

Rack position 12

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 142 140.4 143.6

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 6.7+-0.5

Pump speed r/min 420 420 420

Average injection quantity mm3/st. 13.5 11.5 15.5

Max. variation between cylinders % 0 -13 13

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 142 141 143

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+1

Pump speed r/min 1150 1150 1150

Average injection quantity mm3/st. 138 134 142

Fixing the lever *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Damper spring setting
----------
T1=AD43
----------

Timer adjustment

(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(8)deg t1=1.5--sec t2=1.5--sec
----------
N1=950++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=8+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt setting
----------
aa=42.5mm
----------
a=22.5deg+-5deg b=30deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.)
----------
aa=40mm bb=0r/min cc=1.5+-0.3mm
----------
a=20deg+-5deg b=43deg+-5deg

0000001501 RACK SENSOR

Rack sensor adjustment 1. Flange type rack sensor (rack sensor adjustment -5*20) (1)These types of rack sensors do not need adjustment. Confirm the performance with the following procedures. (2)Mount the rack sensor main body to the pump main body. (3)Fix the pump lever at full. (4)At supply voltage V1, pump speed N1 and rack position Ra, confirm that the amp's output voltage is Vist. (5)Move the pump lever two or three times. (6)Set again to full. (7)Confirm that the amplifier output voltage is Vist. (8)Fix the caution plate to the upper part of the rack sensor. (For those without the caution plate instructions, make sure the nameplate of the rack sensor carries the "Don't hold here" caution.) (9)Apply red paint to the rack sensor mounting bolts (2 places).
----------
V1=5+-0.01V N1=750r/min Ra=R1(12)mm Vist=1.55+-0.14V
----------

Timing setting

(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (4)-
----------
aa=4deg
----------
a=(180deg)

Information:

Please consult SISWEB for serial number prefix specific details.
Features And Benefits
Cat? Reman Fuel Injectors offer excellent value to customers. Customers who want fast repair turn-around, superior quality and reliability, and lower repair costs will benefit from the use of these remanufactured fuel injectors. Cat Reman Fuel Injectors provide immediate, off-the-shelf availability at a fraction of the new price.
Features Benefits
All critical engineering changes and updates included Improved reliability and performance
Worldwide availability through Cat parts distribution system Customer access regardless of location
Backed by Cat warranty Consistent support
Core Acceptance
The Core Acceptance Criteria for Caterpillar Reman Electronic Unit Fuel Injectors is simple, visual, and does not require special tools. Consult your Unit Injectors - Electronic Core Acceptance Criteria SELD0226 for complete details.
Warranty
Please consult the appropriate Cat parts warranty statement for your area.
Core Management
Please refer to the Cat Core Management Information System (CMIS 2) Parts Information application describing all Cat Reman part/CAF and related information. Also refer to other CMIS 2 inquiry applications such as Customer Profiles, Inspection Reason Codes, Inspection Line Inquiry, Add Charge Information, Entitlement Activity, Entitlement Inquiry, CCR Inquiry, CCR Entry, Shipment Processing; Process Packaging Grief; and Reporting to properly manage core returns and monitor inspection performance. This information will be available to all dealers worldwide after your CMIS 2 conversion date. In the meantime, please continue to use the current CMIS
INFORMATION RELEASE MEMO | PAGE 4
Entitlement Parts Inquiry Screen describing the list of parts in a Core Acceptability Family (CAF) and related part number detail.
For the latest updates of Reman Policies and Core Management (SELD0122), Core Management Systems & Operations Procedures (SELD0040), and Shipping Instructions (SELD0039), go to the Reman Dealer websitehttps://catreman.cat.com
If you have any questions regarding core return processing, feel free to call Corinth toll free at (800) 537-2928. For assistance with technical questions, call the Peoria Reman
Technical Help Line also toll free at (888) 88-REMAN or use our E-mail address--Reman_Help.