106961-6014 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1069616014 1156025014

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106961-6014 1069616014

ISUZU 1156025014 1156025014

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106961-6014 zexel genuine, new aftermarket engine parts with delivery

Service parts 106961-6014 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106096-9490

3. GOVERNOR 105488-1281

4. SUPPLY PUMP 105237-1940

5. AUTOM. ADVANCE MECHANIS 105687-0301

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-7851

11. Nozzle and Holder 1-15300-204-1

12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.1{225}

13. NOZZLE-HOLDER 105031-4831

14. NOZZLE

105015-8200

15. NOZZLE SET

Include in #1:

106961-6014 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106961-6014 1069616014

ISUZU 1156025014 1156025014

Zexel num

Bosch num

Firm num

Name

106961-6014
106961-6015

1156025014 ISUZU

INJECTION-PUMP ASSEMBLY
12PD1-N * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve (drive side) 134424-4020

Overflow valve opening pressure (drive side) kPa 255 221 289

Overflow valve opening pressure (drive side) kgf/cm2 2.6 2.25 2.95

Overflow valve (governor side) 134424-4020

Overflow valve opening pressure (governor side) kPa 255 221 289

Overflow valve opening pressure (governor side) kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-9-8- 5-2-11-1 0-3-6-7-

Pre-stroke mm 4.4 4.37 4.43

Rack position
Point A R=A

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-4 deg. 15 14.75 15.25

Difference between angles 2
Cal 1-9 deg. 60 59.75 60.25

Difference between angles 3
Cal 1-8 deg. 75 74.75 75.25

Difference between angles 4
Cal 1-5 deg. 120 119.75 120.25

Difference between angles 5
Cyl.1-2 deg. 135 134.75 135.25

Difference between angles 6
Cal 1-11 deg. 180 179.75 180.25

Difference between angles 7
Cal 1-10 deg. 195 194.75 195.25

Difference between angles 8
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 9
Cal 1-6 deg. 255 254.75 255.25

Difference between angles 10
Cal 1-7 deg. 300 299.75 300.25

Difference between angles 11
Cal 1-12 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point A

Rack position 8.3

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 96.1 94.6 97.6

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 8.6

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 96.8 94.8 98.8

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 7.9

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 101.1 99.1 103.1

Fixing the lever *

Injection quantity adjustment_04

Adjusting point D

Rack position 5.2+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 8.8 7.5 10.1

Max. variation between cylinders % 0 -13 13

Fixing the rack *

Timer adjustment

Pump speed r/min 600--

Advance angle deg. 0 0 0

Load 4/4

Remarks
Start

Timer adjustment_02

Pump speed r/min 550

Advance angle deg. 0.3

Load 4/4

Timer adjustment_03

Pump speed r/min 830+-30

Advance angle deg. 2 1.5 2.5

Load 4/4

Timer adjustment_04

Pump speed r/min 900

Advance angle deg. 2 1.5 2.5

Load 3/4

Timer adjustment_05

Pump speed r/min 1100

Advance angle deg. 5.5 5 6

Load 4/4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Damper spring setting
----------
RT=0.8 TH=1.6mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=7deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=31deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=60deg+-5deg b=73deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (set timing) (4)-
----------
aa=8deg
----------
a=(180deg)

Information:

Illustration 7 g06347860
Injector male spade terminals
There are two options to build injector adapter harness for C3.3.If available, use the injector connector removed from C3.3 harness. Cut both 100 mm wires from the connector and attach bullet terminals that fit in the injector adapter harness C3.8 terminal from injector test kit.If no harness is available, build a harness with the following. Two female spade terminals for injector male spade terminal, two 16 gauge 100 mm wires, and two bullet terminals for injector adapter harness C3.8 terminal.
Illustration 8 g06345429
Injector adapter harness C2.4
Illustration 9 g06346223
Injector adapter harness C3.8
Illustration 10 g06346237
Injector male spade terminals
There are two options to build injector adapter harness for C2.4.If available, use the injector connector removed from C2.4 harness. Cut both 100 mm wires from the connector and attach bullet terminals that fit in the injector adapter harness C3.8 terminal from injector test kit.If no harness is available, build a harness with the following. Two female spade terminals for injector male spade terminal, two 16 gauge 100 mm wires, and two bullet terminals for injector adapter harness C3.8 terminal.Injector Test Set-up
Illustration 11 g06346391
Mounted nozzle test group
Find a suitable stable and surface to either mount or place the nozzle test group. Fill fuel container with #1 diesel and install high-pressure hose assembly. Use adaptors, if needed, based on nozzle tester. Tighten the fuel line adapter to (25 ft lbs). Install the fuel line adapter and tighten to (25 ft lbs) to allow connection to the injector.
Illustration 12 g06346423
Injector holder assembly
Take the injector test kit and remove all parts to assemble, as shown above. Take the injector holder and the clear fuel shield with screws from the kit and remove the screws using a 3mm alan wrench. Assemble the parts so the clear fuel shield with screws is on the bottom. While, the mounted injector holder is on top with the screws removed from before.
Illustration 13 g06346719
Fuel collector and injector holder
Place injector holder onto a fuel collector or another container to capture the injection spray.
Illustration 14 g06346839
Injector setup and harness connection
Install the injector that is needing to be tested into the opening at the top of injector holder. Attach the return fuel drain hose and run the drain hose to another fuel collector. Make the harness connection using the correct adapter for the C2.4, C3.3, and C3.8 engines. Connect the injector pulse tool and the injector adapter harness to the injector.
Illustration 15 g06346868
Complete setup of nozzle tester and injector test kit
Once injector test kit and nozzle test group are set up, connect fuel line adaptor on the high-pressure hose assembly to the injector, leave connection loose. Actuate the lever on the nozzle test group until fuel drips from connection allowing air to purge from setup. Tighten fuel line adaptor at injector to (25 ft lbs).Injector Test Procedure
Illustration 16 g06346881
Mounted nozzle test group (close-up)
Inspect the injector for any leaks. Using the lever on the nozzle tester group, build injection fuel pressure to (5000 psi). Turn the locking valve to insure there is no leakage back through the tester.
Let the nozzle test