Information injection-pump assembly
ZEXEL
106961-1523
1069611523
ISUZU
1156018355
1156018355
Rating:
Service parts 106961-1523 INJECTION-PUMP ASSEMBLY:
1.
_
6.
COUPLING PLATE
7.
COUPLING PLATE
8.
_
9.
_
11.
Nozzle and Holder
1-15300-163-2
12.
Open Pre:MPa(Kqf/cm2)
15.7{160}/22.1{225}
15.
NOZZLE SET
Include in #1:
106961-1523
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Table 1
Sales Model Adaptable to Machines Effective in Production with Machines
D3K 2 S/N:JPJ1-199 S/N:JPJ200-UP
S/N:KL21-208 S/N:KL2209-UP
S/N:LT31-113 S/N:LT3114-UP
S/N:FT31-102 S/N:FT3103-UP
S/N:KF21-174 S/N:KF2175-UP
D4K 2 S/N:KR21-203 S/N:KR2204-UP
S/N:RT31-130 S/N:RT3131-UP
S/N:KM21-196 S/N:KM2197-UP
S/N:MT31-119 S/N:MT3120-UP
D5K 2 S/N:KY21-357 S/N:KY2358-UP
S/N:RRE1-232 S/N:RRE233-UP
S/N:YT31-153 S/N:YT3154-UP
S/N:KW21-308 S/N:KW2309-UP
S/N:WT31-145 S/N:WT3146-UP In the event, the original bolt should come loose or is lost, use one of the following procedures and parts list for reworking the latch assembly.Rework Procedure
Table 2
New Parts List
Item Quantity Part Number Description
1 1 275-0571 Latch Cam
2 1 7X-2619 Bolt
3 1 9X-8256 Washer
4 1 275-0572 Latch As
Illustration 1 g06026857Procedure if the original cam latch retaining bolt is loose
Illustration 2 g06025999
Remove bolt (2), keeping cam latch (1) in position.
Apply Loctite 243 to the threads of bolt (2). Torque the bolt to 6 1 N m (53 9 lb in) using a torque wrench.Procedure if only the original cam latch bolt and cam latch are missing
Illustration 3 g06026021
Install new cam latch (1) to the latch body.
Replace missing retaining bolt with a 7X-2619 Bolt (2) and 9X-8256 Washer (3). This washer is required as the new bolt is too long and will bottom out in the latch body before tightening. Install using Loctite 243. Torque the bolt to 6 1 N m (53 9 lb in) using a torque wrench.Procedure if the original cam latch retaining bolt, cam latch and latch assembly are missing
Illustration 4 g06026825
Illustration 5 g06026826
Illustration 6 g06026831
(E) Side 1 of Retaining Nut
(F) Side 2 of Retaining Nut
Install new latch housing (A), with non-metallic washer (on outside of door) and Latch body/ handle (4) in door.Note: Orient two surfaces (C)and handle as shown in Illustration 5. Lock indicator on outside of handle is at the top.
Secure housing with retaining nut (B) and torque to 15 3 N m (11 2 lb ft), using a torque wrench.Note: During assembly, use four nubs (D) on Side (E) of nut against door.
Remove original bolt (C).
Install latch cam (1).
Apply Loctite 243 to the threads on the original bolt (C). Torque the bolt to 6 1 N m (53 9 lb in).Note: Use torque wrench for tightening.