106873-3391 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068733391 220008741a

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106873-3391 1068733391

HINO 220008741A 220008741a

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106873-3391 zexel genuine, new aftermarket engine parts with delivery

Service parts 106873-3391 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106080-5910

3. GOVERNOR 105923-1261

4. SUPPLY PUMP 105237-0010

5. AUTOM. ADVANCE MECHANIS 105683-0420

6. COUPLING PLATE 105664-2170

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-7793

11. Nozzle and Holder 23600-2741B

12. Open Pre:MPa(Kqf/cm2) 14.7{150}/24.5{250}

13. NOZZLE-HOLDER 105030-3581

14. NOZZLE

15. NOZZLE SET 105019-0541

Include in #1:

106873-3391 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106873-3391 1068733391

HINO 220008741A 220008741a

Zexel num

Bosch num

Firm num

Name

106873-3391
106873-3392

220008741A HINO

INJECTION-PUMP ASSEMBLY
F-2 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131425-0020

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-6-2- 7-5-4-3

Pre-stroke mm 4.2 4.14 4.2

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-6 deg. 90 89.75 90.25

Difference between angles 3
Cyl.1-2 deg. 135 134.75 135.25

Difference between angles 4
Cal 1-7 deg. 180 179.75 180.25

Difference between angles 5
Cal 1-5 deg. 225 224.75 225.25

Difference between angles 6
Cal 1-4 deg. 270 269.75 270.25

Difference between angles 7
Cal 1-3 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point -

Rack position 13.6

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 149.5 146.5 152.5

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 8.5+-0.5

Pump speed r/min 250 250 250

Average injection quantity mm3/st. 12 9 15

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(13.6)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 149.5 147.5 151.5

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1-0.2

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 136.5 130.5 142.5

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1-0.2

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 148 142 154

Fixing the lever *

Timer adjustment

Pump speed r/min 710--

Advance angle deg. 0 0 0

Load 2/5

Remarks
Start

Timer adjustment_02

Pump speed r/min 660

Advance angle deg. 0.3

Load 2/5

Timer adjustment_03

Pump speed r/min (760)

Advance angle deg. 2 1.7 2.3

Load 5/5

Remarks
Measure the actual speed.

Timer adjustment_04

Pump speed r/min 900+50

Advance angle deg. 2 1.7 2.3

Load 4/5

Timer adjustment_05

Pump speed r/min 1100-50

Advance angle deg. 5.5 5.2 5.8

Load 5/5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Set stop lever before governor adjustment. [When setting stop lever after governor adjustment, confirm that point I (Ra) can be obtained at full setting.] (4)Stop lever's normal position setting: equivalent to R1 (5)Damper spring setting
----------
T1=AC70 Ra=R1+1.9mm R1=18mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=79mm
----------
a=12deg+-5deg b=28deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Rack position = approximately aa. (2)Set the stopper screw. (After setting, apply red paint.) (3)Speed = bb, rack position = cc (4)Set the stopper screw. (After setting, apply red paint.) (5)Use the hole above R = dd
----------
aa=18mm bb=0r/min cc=1.5+-0.3mm dd=35mm
----------
a=35deg+-5deg b=15deg+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)

Information:

General Torque Information
Mismatched or incorrect fasteners can result in damage or malfunction, or possible injury.Take care to avoid mixing metric dimensioned fasteners and inch dimensioned fasteners.
Exceptions to these torques are given in the Service Manual, if necessary.Prior to installing any hardware, ensure that the components are in near new condition. Bolts and threads must nor be worn or damaged. Threads must not have burrs or nicks. Hardware must be free of rust and corrosion. Clean the hardware with a noncorrosive cleaner. Do not lubricate the fastener threads except with rust preventive. The rust preventive should be applied by the supplier of that component for purposes of shipping and storage. Other applications for lubricating components may also be specified in the Service Manual.For additional torque specifications, refer to SENR3130, Torque Specifications, available from your Caterpillar dealer.Standard Torque for Bolts, Nuts and Taperlock Studs
Torques for Taperlock Studs
Use these standard torque values for all fasteners unless otherwise specified in this manual or in the Service Manual.Torque for Metric Fasteners
Torque for Standard Hose Clamps-Worm Drive Band Type
The chart that follows gives the torques for initial installation of hose clamps on new hose and for reassembly or tightening of hose clamps on existing hose.
Torque for Constant Torque Hose Clamps
A constant torque hose clamp can be used in place of any standard hose clamp. Make sure the constant torque hose clamp is the same size as the standard clamp. Due to extreme temperature changes, hose will heat set. Heat setting causes hose clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures caused by hose clamps loosening. The constant torque hose clamp will help prevent these failures. Use a torque wrench for proper installation of the constant torque hose clamp. The constant torque hose clamp is installed correctly under the following conditions: * Screw tip (1) extends 6.35 mm (.250 in) (X) beyond the housing.* The belleville washers are collapsed nearly flat after screw (2) is tightened to a torque of 11 1 N m (98 9 lb in).