106873-3232 ZEXEL F 01G 09U 0AY BOSCH INJECTION-PUMP ASSEMBLY f01g09u0ay 1068733232

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH F 01G 09U 0AY f01g09u0ay

ZEXEL 106873-3232 1068733232

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106873-3232 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

BOSCH F 01G 09U 0AY f01g09u0ay

ZEXEL 106873-3232 1068733232

Zexel num

Bosch num

Firm num

Name

106873-3232
106873-3233

F 01G 09U 0AY

INJECTION-PUMP ASSEMBLY
* K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-0820

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-6-2- 7-5-4-3

Pre-stroke mm 4.5 4.44 4.5

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-6 deg. 90 89.75 90.25

Difference between angles 3
Cyl.1-2 deg. 135 134.75 135.25

Difference between angles 4
Cal 1-7 deg. 180 179.75 180.25

Difference between angles 5
Cal 1-5 deg. 225 224.75 225.25

Difference between angles 6
Cal 1-4 deg. 270 269.75 270.25

Difference between angles 7
Cal 1-3 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point -

Rack position 13.9

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 150 147 153

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 8.5+-0.5

Pump speed r/min 250 250 250

Average injection quantity mm3/st. 11 8 14

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(13.9)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 150 148 152

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.05

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 142.5 136.5 148.5

Fixing the lever *

Timer adjustment

Pump speed r/min 600--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 550

Advance angle deg. 0.3

Timer adjustment_03

Pump speed r/min (620)

Advance angle deg. 0.7 0.4 1

Timer adjustment_04

Pump speed r/min 980+50

Advance angle deg. 0.7 0.4 1

Timer adjustment_05

Pump speed r/min 1100-50

Advance angle deg. 3.5 3.2 3.8

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Stop lever's normal position setting: R1
----------
T1=AA19 R1=(18)mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=79mm
----------
a=12deg+-5deg b=27deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Set the stopper screw. (After setting, apply red paint.) (3)Speed = bb, rack position = cc (4)Set the stopper screw. (After setting, apply red paint.) (5)Use the hole above R = dd
----------
aa=(18)mm bb=0r/min cc=1.5+-0.3mm dd=35mm
----------
a=35deg+-5deg b=15deg+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)

Information:

Owner Warranty Rights And Obligations
The California Air Resources Board (CARB) and Caterpillar Inc. are pleased to explain the emission control system warranty on your 1991 truck engine.In California, new motor vehicle engines must be designed, built and equipped to meet the state's stringent anti-smog standards. Caterpillar Inc. must warrant the emission control system on your truck engine for the duration of time listed below provided there has not been any abuse, neglect or improper maintenance of your truck engine.Your emission control system may include parts such as the fuel injection system and engine computer, if equipped. Also included may be hoses, connectors, clamps and other emission-related components.Where a warrantable condition exists, Caterpillar Inc. will repair the truck engine at no cost to the owner including diagnosis, parts and labor.Manufacturer's Warranty Coverage
* The emissions warranty period for new truck engines is a duration of 60 months, 100,000 miles (161 000 km), or 3,000 hours of operation, whichever occurs first.* If an emission related part or component on your truck engine is defective, the part or component will be repaired or replaced by Caterpillar Inc. This is your emission control system WARRANTY.Owner's Warranty Responsibilities
* As the truck engine owner, you are responsible for the performance of the required maintenance listed in the truck engine owner's manual (Operation and Maintenance Manual). Caterpillar Inc. recommends that you retain all receipts and records covering the maintenance on your truck engine, but cannot deny warranty solely for the lack of receipts and records or for you failure to ensure the performance of all scheduled maintenance.* You are responsible for presenting your truck engine to a Caterpillar Inc. dealer as soon as a truck engine problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.* As the truck engine owner, you should also be aware that Caterpillar Inc. may deny you warranty coverage if your truck engine or an emission component or part has failed due to abuse, neglect, improper maintenance or unapproved modifications.If you have questions regarding your warranty rights and responsibilities, contact:Caterpillar Inc.
Manager, Truck Engine Business
Peoria, IL 61629
Phone (309) 578-6288
ORCalifornia Air Resources Board (CARB)
9528 Telstar Ave.
El Monte, CA91731
Emissions Warranty
Caterpillar Inc. warrants to the initial owner and subsequent owner of a diesel truck engine (powering an on-highway truck), that such engine is ...1. Designed, built and equipped so as to conform, at the time of sale, with all applicable regulations adopted by the California Air Resources Board (CARB).2. Free from defects in materials and workmanship in specific emission related parts for a period of 60 months, 100,000 miles (161 000 km) or 3,000 hours of operation, whichever occurs first, after date of delivery to the initial owner.If an emission related part fails during the warranty period, it will be repaired or replaced. Any such part repaired or replaced under warranty is warranted for the remainder of the warranty period.During the term of this warranty, Caterpillar Inc. will provide through a Caterpillar dealer or other establishment