106871-9042 ZEXEL 9 400 618 320 BOSCH INJECTION-PUMP ASSEMBLY 9400618320 1068719042

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 618 320 9400618320

ZEXEL 106871-9042 1068719042

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-9042 zexel genuine, new aftermarket engine parts with delivery

Service parts 106871-9042 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106087-5510

3. GOVERNOR 105487-5320

4. SUPPLY PUMP 105207-1140

5. AUTOM. ADVANCE MECHANIS 105636-0770

6. COUPLING PLATE 105663-0260

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-7431

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 17.7(180)/21.6(220)

13. NOZZLE-HOLDER 105030-4980

14. NOZZLE

105015-7310

15. NOZZLE SET

Include in #1:

106871-9042 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 618 320 9400618320

ZEXEL 106871-9042 1068719042

Zexel num

Bosch num

Firm num

Name

106871-9042

9 400 618 320

HYUNDAI

INJECTION-PUMP ASSEMBLY
8DC9 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-1320

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-7-3- 4-5-6-8

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cyl.1-2 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-3 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-5 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-6 deg. 270 269.5 270.5

Difference between angles 7
Cal 1-8 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point -

Rack position 9.5

Pump speed r/min 700 700 700

Each cylinder's injection qty mm3/st. 118 114.5 121.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point F

Rack position 5.8+-0.5

Pump speed r/min 450 450 450

Each cylinder's injection qty mm3/st. 17 15.3 18.7

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(9.5)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 118 117 119

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1(9.5)

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 124 118.8 129.2

Difference in delivery mm3/st. 10.4 10.4 10.4

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position 6.1+-0.5

Pump speed r/min 225 225 225

Each cylinder's injection qty mm3/st. 20 17 23

Fixing the rack *

Remarks
(check)

Injection quantity adjustment_06

Adjusting point E

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 155 135 175

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 950--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 900

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1000

Advance angle deg. 1.8 1.1 2.5

Timer adjustment_04

Pump speed r/min 1100

Advance angle deg. 3.5 3.5

Timer adjustment_05

Pump speed r/min 1150

Advance angle deg. 6.5 6 7

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Excess fuel setting for starting: SXL (3)Damper spring setting
----------
SXL=(R1+0.2)+-0.1mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=19deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=26deg+-3deg

Stop lever angle

N:Engine manufacturer's normal use S:Stop the pump. (1)Rack position = aa (2)Stopper bolt setting (3)Rack position bb (4)Free (at shipping) (5)R = cc
----------
aa=4-0.5mm bb=11.7mm cc=36mm
----------
a=45.5deg+7deg-5deg b=22deg+-5deg c=(10.5deg)

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(40deg)

Information:

4. Put clean engine oil on the O-ring seal, and assemble elbow (4) to drain tube (5).5. Put the gaskets in position on the block and on the turbocharger, and install the drain tube assembly. 6. Put a gasket in position between oil supply tube (6) and the turbocharger. Install oil supply tube (6).Disassemble Turbocharger (TV72 & TV78)
START BY:a. remove turbocharger (TV72 & TV78) 1. Install the turbocharger in tool group (A). Put alignment marks on the three housings of the turbocharger for correct installation and alignment at assembly. Remove "V" clamp (2) and compressor housing (1). 2. Remove "V" clamp (3). Remove cartridge housing (5) from turbine housing (4).
When the nut is loosened, do not put a side force on the shaft. This can result in a bent shaft.
3. Install tool (C) in tool (B), and put the cartridge assembly in tool (C) as shown. Use tool (D) to remove the nut that holds compressor wheel (6). 4. Put the cartridge assembly in tool (E), and use a press (if necessary) to remove compressor wheel (6) from the turbine wheel and shaft assembly. Do not let the turbine wheel and shaft assembly fall during removal of the compressor wheel from the turbine wheel and shaft. 5. Remove seal ring (7) and shroud (8) from turbine wheel and shaft assembly (9). 6. Bend the tabs of the locks from bolts (10), and remove the bolts and locks.7. Remove backplate assembly (11) from the cartridge housing. 8. Remove spacer (12) from backplate assembly (11). Remove seal rings (13) from spacer (12). 9. Remove collar (14), thrust bearing (15) and O-ring seal (16) from the cartridge housing. 10. Remove top bearing (17) and the washer from the cartridge housing. Put a long dye mark on the top face of bearing (17).11. Use tool (F), and remove the two rings that hold the top and bottom bearings in position. Remove the bottom bearing and washer. Put a short dye mark on the bearing. The dye marks are used for identification of the bearings when they are installed.12. Use tool (F), and remove the last ring that holds the bottom bearing in position from the cartridge housing.13. Check all the parts of the turbocharger for damage. If the parts are damaged, use new parts for replacement. See Special Instruction Form No. SMHS6854 for Turbocharger Reconditioning. Also see Guidelines For Reuseable Parts, Form No. SEBF8018.Assemble Turbocharger (TV72 & TV78)
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material.2. Put clean engine oil on all parts of the cartridge assembly.
Rings (1), (4) and (5) must be installed with the round edge of the outside diameter of the rings toward the bearings.
3. Install ring (4) in the cartridge