106871-9035 ZEXEL 9 400 618 319 BOSCH INJECTION-PUMP ASSEMBLY 9400618319 1068719035

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 618 319 9400618319

ZEXEL 106871-9035 1068719035

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-9035 zexel genuine, new aftermarket engine parts with delivery

Service parts 106871-9035 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106087-5730

3. GOVERNOR 105306-1106

4. SUPPLY PUMP 105207-1140

5. AUTOM. ADVANCE MECHANIS 105636-1200

6. COUPLING PLATE 105663-0260

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-7431

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 17.7(180)/21.6(220)

13. NOZZLE-HOLDER 105030-4980

14. NOZZLE

105015-7310

15. NOZZLE SET

Include in #1:

106871-9035 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 618 319 9400618319

ZEXEL 106871-9035 1068719035

Zexel num

Bosch num

Firm num

Name

106871-9035

9 400 618 319

HYUNDAI

INJECTION-PUMP ASSEMBLY
8DC9 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-1320

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-7-3- 4-5-6-8

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cyl.1-2 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-3 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-5 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-6 deg. 270 269.5 270.5

Difference between angles 7
Cal 1-8 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point -

Rack position 8.8

Pump speed r/min 700 700 700

Each cylinder's injection qty mm3/st. 97 94.1 99.9

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point F

Rack position 5.8+-0.5

Pump speed r/min 450 450 450

Each cylinder's injection qty mm3/st. 17 15.3 18.7

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(8.8)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 97 96 98

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1(8.8)

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 105.7 101.5 109.9

Difference in delivery mm3/st. 8.4 8.4 8.4

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position 6.1+-0.5

Pump speed r/min 225 225 225

Each cylinder's injection qty mm3/st. 20 17 23

Fixing the rack *

Remarks
(check)

Injection quantity adjustment_06

Adjusting point E

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 115 95 135

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 950--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 900

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1000

Advance angle deg. 1.7 1.2 2.2

Timer adjustment_04

Pump speed r/min 1150

Advance angle deg. 6.5 6 7

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Rack limit using stop lever: RA (2)Excess fuel setting for starting: SXL (3)Damper spring setting: DL
----------
RA=11.6+-0.1mm SXL=(R1+0.9)+-0.1mm DL=4.3-0.2mm
----------

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=16deg+-3deg b=16deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa, stopper bolt setting (2)Rack position bb
----------
aa=4-0.5mm bb=11.6+-0.1mm
----------
a=5deg+-6deg b=34deg+-6deg

0000001501 MICRO SWITCH

Switch adjustment Adjust the bolt so that the lower lever position is obtained when the switch is turned ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-25r/min Ra=5.6mm
----------

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(40deg)

Information:

1. Put the fuel injection pump housing in position on tool (A). Install race (3), bearing (2) and race (1) on the end of the camshaft in the fuel injection pump housing. 2. Put flyweights (5) in position on carrier assembly (4), and install dowels (6) to hold the flyweights in place. The flyweights must move freely on the dowels and have 0.010 to 0.230 mm (.0004 to .0090 in.) end play. 3. Install governor shaft (7) on carrier assembly (4). 4. Install dowel (8) in governor shaft (7), and slide carrier assembly (4) down on the governor shaft until dowel (8) fits into the slot in the carrier assembly.5. Install carrier assembly (4) on the end of the camshaft. 6. Install race (12), bearing (11), race (10) and ring (9) on riser (13). 7. Install riser (13) and spring (14), if equipped, on the governor shaft. 8. Install spool (18) and ring (19) on seat (17), and use tool (B) to install ring (20) to hold them in position.9. Install seat (17) on spring (16) and spring (16) on shield (15). 10. Install dashpot assembly (21) on the governor shaft. 11. Install ring (22) in the groove on the governor shaft. Install sleeve (23), spring (25), the sleeve and bearing (24) on the governor shaft. 12. Use tool (C) to hold spring (25) under compression, and install the ring in the groove on the governor shaft. 13. Put lever (32) in position on governor servo (30), and install pin (31) to hold the lever in place. Use a hammer and chisel to move the metal (stake) four places 90° apart on