106871-8570 ZEXEL 9 400 618 283 BOSCH INJECTION-PUMP ASSEMBLY 9400618283 1068718570 220006850a

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 618 283 9400618283

ZEXEL 106871-8570 1068718570

HINO 220006850A 220006850a

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-8570 zexel genuine, new aftermarket engine parts with delivery

Service parts 106871-8570 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106087-5790

3. GOVERNOR 105489-2320

4. SUPPLY PUMP 105237-1410

5. AUTOM. ADVANCE MECHANIS 105636-1540

6. COUPLING PLATE 105662-0850

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-5100

11. Nozzle and Holder 23600-1530

12. Open Pre:MPa(Kqf/cm2) 18.1{185}

13. NOZZLE-HOLDER 105031-5400

14. NOZZLE

105015-4700

15. NOZZLE SET

Include in #1:

106871-8570 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 618 283 9400618283

ZEXEL 106871-8570 1068718570

HINO 220006850A 220006850a

Zexel num

Bosch num

Firm num

Name

106871-8570

9 400 618 283

220006850A HINO

INJECTION-PUMP ASSEMBLY
EF750 * K 14CD PE8P PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-1020

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-6-2- 7-5-4-3

Pre-stroke mm 4.4 4.34 4.4

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-6 deg. 90 89.75 90.25

Difference between angles 3
Cyl.1-2 deg. 135 134.75 135.25

Difference between angles 4
Cal 1-7 deg. 180 179.75 180.25

Difference between angles 5
Cal 1-5 deg. 225 224.75 225.25

Difference between angles 6
Cal 1-4 deg. 270 269.75 270.25

Difference between angles 7
Cal 1-3 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point A

Rack position 9.5

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 120 117 123

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 9.6

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 121.8 119.8 123.8

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 10.4

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 145 142 148

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_04

Adjusting point D

Rack position 5.4+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 11.5 8.5 14.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_05

Adjusting point E

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 140 140 160

Fixing the lever *

Remarks
After startup boost setting

Injection quantity adjustment_06

Adjusting point H

Rack position 9.6+-0.5

Pump speed r/min 1175 1175 1175

Average injection quantity mm3/st. 126 121 131

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Timer adjustment

Pump speed r/min 750--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 700

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1100

Advance angle deg. 3.5 3.2 3.8

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Excess fuel setting for starting: SXL (4)Damper spring setting: DL
----------
RT=0.8 TH=2.7mm SXL=10.4+0.2mm DL=4.4-0.2mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=23deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting (2)Use the hole at R = aa
----------
aa=50mm
----------
a=39deg+-3deg b=39deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Set stopper screw so that rack position = aa (after setting, apply red paint).
----------
aa=13+-0.1mm
----------
a=47deg+-5deg b=33.5deg+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)

Information:

preparatory steps: a) remove flywheel housingb) remove timing gear coverc) remove pistons1. Lay the engine on its side or top in a suitable stand.2. Attach a hoist to the crankshaft. 3. Remove the main bearing caps (1). 4. Remove the crankshaft-weight 200 lbs. (91 kg).5. Remove the crankshaft main bearings from the cylinder block and main bearing caps.
If the main bearings are not going to be replaced mark them with respect to their location in the engine.
6. Using tool setup (A), remove the crankshaft gear and oil seal wear sleeve.Install Crankshaft
1. Heat the crankshaft gear and the oil seal wear sleeve, maximum 600°F (316°C), and install them on the crankshaft.2. Clean the bearing seating surfaces in the cylinder block and the main bearing caps. Install the upper and lower halves of the bearings in the cylinder block bearing caps. Lubricate the bearings with clean SAE 30 engine oil.
If the main bearings are not being replaced the original bearings must be installed in the same location they were removed from.
3. Attach a hoist and position the crankshaft in the cylinder block with the timing marks (1) aligned. 4. Using wire (A), check the main bearing clearance. Install the caps in the respective positions with the number stamped on cap facing the corresponding number cast on side of the cylinder block web. 5. Lubricate the threads of bearing cap retaining bolts and face of washers with clean SAE 30 engine oil. Install the retaining bolts and washers. Tighten both bolts to 30 3 lb. ft. (4,1 0,4 mkg). Mark both bolt heads and bearing caps then tighten each bolt an additional 90° from mark. Remove bearing caps and measure thickness of wire (A). Main bearing clearance should be .0030-.0059 in. (0,076-0,150 mm).6. Lubricate the lower halves of main bearings with clean SAE 30 engine oil. Install main bearing caps in their respective positions. Install cap retaining bolts and washers. Tighten both bolts to 30 3 lb. ft. (4,1 0,4 mkg). Mark both bolt heads and bearing caps then tighten each bolt an additional 90° from mark. 7. Using tool setup (B), check the crankshaft end play as controlled by thrust bearing (2) on rear main bearing. End play should be .0025-.0145 in. (0,064-0,368 mm). Maximum permissible end play is .025 in. (0,64 mm).concluding steps: a) install pistonsb) install timing gear coverc) install flywheel housingd) check fuel injection pump timing. See REMOVE AND INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR AS A UNIT.