106871-7571 ZEXEL 9 400 618 217 BOSCH INJECTION-PUMP ASSEMBLY 9400618217 1068717571 me065921


 

Information injection-pump assembly

BOSCH 9 400 618 217 9400618217
ZEXEL 106871-7571 1068717571
MITSUBISHI ME065921 me065921
106871-7571 INJECTION-PUMP ASSEMBLY
Rating:
64
Buy INJECTION-PUMP ASSEMBLY 106871-7571 zexel genuine, new aftermarket engine parts with delivery

Service parts 106871-7571 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106087-5600
3. GOVERNOR 105487-3381
4. SUPPLY PUMP 105207-1140
5. AUTOM. ADVANCE MECHANIS 105636-1660
6. COUPLING PLATE 105663-0260
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-7431
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 17.7(180)/21.6(220)
13. NOZZLE-HOLDER 105030-4980
14. NOZZLE 105015-7310
15. NOZZLE SET

Include in #1:

106871-7571 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
106871-7571 
9 400 618 217 
ME065921  MITSUBISHI
INJECTION-PUMP ASSEMBLY
8DC82 * K




Information:

1. Remove two bolts (1) from the top of the water pump. Loosen two bolts (2) in the water pump.
TYPICAL EXAMPLE2. Remove oil supply line (3) from the turbocharger. Remove oil return line (4) from the turbocharger.
TYPICAL EXAMPLE3. Remove the bolts (5) that hold the cylinder head to the cylinder block.
TYPICAL EXAMPLE4. Fasten a hoist to the cylinder head assembly (6). Remove the cylinder head assembly from the block. Weight of the assembly is 290 lb. (131 kg). Remove O-ring seal from hollow dowel. Remove cylinder head gasket (7) and water ferrules.
Do not put the cylinder head down on a flat surface. This can cause damage to the fuel injection valves.
Always install a new gasket between spacer plate and cylinder block before cylinder head is installed. See REMOVE SPACER PLATE.Install Cylinder Head
TYPICAL EXAMPLE1. Thoroughly clean the spacer plate and bottom surface of the cylinder head. Install a new head gasket (2), water ferrules (1) and O-ring seal (3) on the hollow dowel. Be sure a new gasket has been installed between spacer plate and cylinder block. See INSTALL SPACER PLATE.2. Fasten a hoist and install the cylinder head assembly (4) on the cylinder block. 3. Install the push rods and put the rocker shaft in position on the cylinder head. Put 5P3931 Anti-Seize Compound on the threads of the cylinder head and rocker shaft bolts. Install the bolts and washers and tighten the bolts as follows: 1. Tighten all bolts in number sequence to a torque of 115 lb. ft. (155 N m).2. Again tighten all bolts in number sequence to a torque of 185 13 lb. ft. (250 17 N m).3. Again tighten all bolts in number sequence (hand torque only) to a torque of 185 13 lb. ft. (250 17 N m).4. Tighten all bolts in letter sequence to a torque of 32 5 lb. ft. (43 7 N m).4. Make adjustment of valves to have a clearance of .015 in. (0.38 mm) for intake and .025 in. (0.64 mm) for exhaust.
TYPICAL EXAMPLE5. Install oil return line (6) on the turbocharger.6. Install oil supply line (5) on the turbocharger. 7. Tighten the two bolts (8) in the water pump.8. Install the two bolts (7) that hold the water pump to the cylinder head.end by: a) install fuel injection lines

Have questions with 106871-7571?





Group cross 106871-7571 ZEXEL

Mitsubishi 

 
 
INJECTION-PUMP ASSEMBLY
8DC91T2
9 400 618 214 
ME065937 
INJECTION-PUMP ASSEMBLY
8DC91T2
9 400 618 215 
ME090372 
INJECTION-PUMP ASSEMBLY
8DC82
 
ME065940 
INJECTION-PUMP ASSEMBLY
8DC91
 
ME065941 
INJECTION-PUMP ASSEMBLY
8DC91
 
ME065942 
INJECTION-PUMP ASSEMBLY
8DC91
9 400 618 216 
ME090467 
INJECTION-PUMP ASSEMBLY
8DC82
 
ME090613 
INJECTION-PUMP ASSEMBLY
8DC9
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

106871-7571  
9 400 618 217 
ME065921 
INJECTION-PUMP ASSEMBLY
8DC82
9 400 618 218 
ME090645 
INJECTION-PUMP ASSEMBLY
8DC9T2
9 400 618 219 
ME090641 
INJECTION-PUMP ASSEMBLY
8DC9T7
Back to top