106871-5510 ZEXEL 9 400 611 020 BOSCH INJECTION-PUMP ASSEMBLY 9400611020 1068715510 1680197564


 

Information injection-pump assembly

BOSCH 9 400 611 020 9400611020
ZEXEL 106871-5510 1068715510
NISSAN-DIESEL 1680197564 1680197564
106871-5510 INJECTION-PUMP ASSEMBLY
Rating:
26
Buy INJECTION-PUMP ASSEMBLY 106871-5510 zexel genuine, new aftermarket engine parts with delivery

Service parts 106871-5510 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106080-5730
3. GOVERNOR 105952-2020
4. SUPPLY PUMP 105237-4710
5. AUTOM. ADVANCE MECHANIS 105683-0710
6. COUPLING PLATE 105663-0570
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105110-7651
11. Nozzle and Holder 16600-97160
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.6{230}
13. NOZZLE-HOLDER 105041-3150
14. NOZZLE
15. NOZZLE SET 105019-0591

Include in #1:

106871-5510 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 611 020 9400611020
ZEXEL 106871-5510 1068715510
NISSAN-DIESEL 1680197564 1680197564


Zexel num
Bosch num
Firm num
Name
106871-5510 
106871-5573 
9 400 611 020 
1680197564  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
RH8 * K 14CD INJECTION PUMP ASSY PE8P PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0120
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
RED3 control unit part number   407910-3 960
RED3 rack sensor specifications mm   19
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-7-5- 4-3-6-2
Pre-stroke mm   4.4 4.37 4.43
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-7
deg.   90 89.75 90.25
Difference between angles 3
Cal 1-5
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-4
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-3
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-6
deg.   270 269.75 270.25
Difference between angles 7
Cyl.1-2
deg.   315 314.75 315.25
Injection quantity adjustment
Rack position   (13.2)
Vist V   1.87 1.87 1.87
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   128 126 130
Max. variation between cylinders %   0 -4 4
Basic   *
Injection quantity adjustment_02
Rack position   (8.6)
Vist V   2.6 2.5 2.7
Pump speed r/min   390 390 390
Average injection quantity mm3/st.   16 14 18
Max. variation between cylinders %   0 -10 10
Governor adjustment
Pump speed r/min   750--
Advance angle deg.   0 0 0
Remarks
At Q=169+-2 (mm3/st) / N=700 (r/min), start of advance
 
Governor adjustment_02
Pump speed r/min   700
Advance angle deg.   0.3
Remarks
Q=169+-2 (mm3/st) / N=700 (r/min)
 
Governor adjustment_03
Pump speed r/min   (750)
Advance angle deg.   2 1.7 2.3
Remarks
Q=169+-2 (mm3/st) / N=700 (r/min)
 
Governor adjustment_04
Pump speed r/min   850
Advance angle deg.   2 1.7 2.3
Remarks
Q=97+-2 (mm3/st) / N=850 (r/min)
 
Governor adjustment_05
Pump speed r/min   1100
Advance angle deg.   7 6.7 7.3
Remarks
Q=162+-2 (mm3/st) / N=1100 (r/min), end of advance
 

Test data Ex:

Speed control lever angle

Test data 106871-5510
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=27deg+-5deg b=37deg+-5deg

0000000901

Test data 106871-5510
(1)Pump vertical direction (2)Position of the coupling's key groove at the beginning of injection of the No. 8 cylinder. (3)- (4)-
----------

----------
a=(90deg)

Stop lever angle

Test data 106871-5510
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------




Information:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.
This Program must be administered as soon as possible. When reporting the repair, use "PI3781" as the Part Number, "7751" as the Group Number, "56" as the Warranty Claim Description Code and "T" as the SIMS Description Code. Exception: If the repair is done after failure, use "PI3781" as the Part Number, "7751" as the Group Number, "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.
This Revised Service Letter replaces the June 21, 1995 Service Letter. Changes have been made to the Parts Needed.
Completion Date
December 31, 1995Termination Date
June 30, 1996Problem
The fuel injector tip may fail on certain 3406E Truck Engines.
Affected Product
Model & Identification Number
3406E (5EK371, 5EK378-380, 5EK382, 5EK403, 5EK405, 5EK435, 5EK453, 5EK455, 5EK461, 5EK485, 5EK486, 5EK500-502, 5EK509, 5EK510, 5EK515, 5EK516, 5EK518, 5EK527, 5EK538, 5EK544, 5EK555, 5EK570, 5EK593, 5EK602, 5EK609, 5EK619, 5EK634, 5EK639, 5EK642, 5EK649, 5EK658, 5EK660, 5EK664, 5EK670-672, 5EK674, 5EK676, 5EK677, 5EK685, 5EK686, 5EK691, 5EK698, 5EK710, 5EK714, 5EK726, 5EK731, 5EK732, 5EK734, 5EK743-746, 5EK750, 5EK752, 5EK756, 5EK767-770, 5EK772, 5EK777-874, 5EK876-878, 5EK880-883, 5EK885-905, 5EK907, 5EK908, 5EK912-919, 5EK921, 5EK931, 5EK933-1025, 5EK1028-1061, 5EK1064-1070, 5EK1072, 5EK1074-1098, 5EK1101-1118, 5EK1122-1140, 5EK1144-1155, 5EK1158-1190, 5EK1195-1208, 5EK1212-1220, 5EK1222-1252, 5EK1254-1297, 5EK1299, 5EK1300, 5EK1302, 5EK1303, 5EK1305, 5EK1307-1310, 5EK1313, 5EK1319, 5EK1322, 5EK1324, 5EK1326, 5EK1327, 5EK1329-1334, 5EK1336, 5EK1337, 5EK1340, 5EK1341, 5EK1343, 5EK1344, 5EK1346, 5EK1348-1372, 5EK1374-1379, 5EK1381-1384, 5EK1390-1425, 5EK1427-1433, 5EK1435-1451, 5EK1454-1459, 5EK1461, 5EK1463, 5EK1465, 5EK1468-1485, 5EK1489-1491, 5EK1493, 5EK1494, 5EK1496, 5EK1512-1517, 5EK1520-1522, 5EK1530, 5EK1531, 5EK1533, 5EK1539-1541, 5EK1543, 5EK1545-1562, 5EK1567, 5EK1569-1628, 5EK1630-1662, 5EK1664, 5EK1668-1680, 5EK1682-1693, 5EK1699-1716, 5EK1718-1746, 5EK1750, 5EK1753, 5EK1755-1811)
Parts Needed
Dealers will need to order parts for this Program.
6 - 0R4893 Injector Group (reman part number for 1171148) (used on 435 HP ratings 5EK371-1184, except 5EK988, 989, 1003, 1004, 1011, 1036, 1076)or6 - 0R4894 Injector Group (reman part number for 1188010) (used on 355, 375 and 435 HP ratings 5EK1185-1811, includes 5EK988, 989, 1003, 1004, 1011, 1036, 1076)or6 - 0R4895 Injector Group (reman part number for 1187929) (used on 410 HP ratings)Action Required
See attached rework procedure.
Service Claim Allowances
Cab Types
SC = Ford LN, L, LS, LA, Short ConventionalMC = Medium Hood ConventionalCV = Long Hood ConventionalCO = Cab OverParts Disposition
U.S. and Canadian Dealers
Return all fuel injectors that are removed from engines along with a copy of the claim and the Core Credit Request form (CCR) to:
Caterpillar Inc.
Attn: Jack Hoobler/PI3781
Service Claims Room
8201 N. University
Peoria, IL 61615
All Other Dealers
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
1. Remove the necessary air piping, air cleaners, valve covers, Jake Brakes, and rocker arm assemblies.2. Before removing fuel injectors from engine, be sure to drain fuel from fuel system.The recommended procedure is to blow compressed air through system via the fuel filter air bleed cap.Remove the fuel injectors from the engine.Immediately clean off excess engine oil and place the fuel injectors in individual clean plastic bags.Use care to prevent dirt from entering the

Have questions with 106871-5510?





Group cross 106871-5510 ZEXEL

Nissan-Diesel 

9 400 611 019 
1680197563 
INJECTION-PUMP ASSEMBLY
RG8
106871-5510  

106871-5573 
9 400 611 020 
1680197564 
INJECTION-PUMP ASSEMBLY
RH8
9 400 618 170 
1680197566 
INJECTION-PUMP ASSEMBLY
RG8
F 01G 09U 09Z 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A0 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A1 
 
INJECTION-PUMP ASSEMBLY
RF8

Nissan-Diesel 

9 400 618 171 
1680197568 
INJECTION-PUMP ASSEMBLY
RF8
 
1680197573 
INJECTION-PUMP ASSEMBLY
RF8TA
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 618 172 
1680197579 
INJECTION-PUMP ASSEMBLY
RF8TA
F 01G 09U 0A2 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A3 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A4 
 
INJECTION-PUMP ASSEMBLY
RG8

Nissan-Diesel 

9 400 618 173 
1680197569 
INJECTION-PUMP ASSEMBLY
RG8
 
1680197570 
INJECTION-PUMP ASSEMBLY
RG8
F 01G 09U 0A5 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A6 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 618 174 
1680197578 
INJECTION-PUMP ASSEMBLY
RG8
F 01G 09U 0A7 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A8 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A9 
 
INJECTION-PUMP ASSEMBLY
RH8

Nissan-Diesel 

9 400 618 175 
1680197571 
INJECTION-PUMP ASSEMBLY
RH8
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 619 880 
 
INJECTION-PUMP ASSEMBLY
RF8

Nissan-Diesel 

9 400 618 176 
1680197574 
INJECTION-PUMP ASSEMBLY
RF8
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0AA 
 
INJECTION-PUMP ASSEMBLY
RG8

Nissan-Diesel 

9 400 618 177 
1680197575 
INJECTION-PUMP ASSEMBLY
RG8
Back to top