106871-5122 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068715122

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106871-5122 1068715122

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-5122 zexel genuine, new aftermarket engine parts with delivery

Service parts 106871-5122 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106080-5432

3. GOVERNOR 105489-4160

4. SUPPLY PUMP 105237-6020

5. AUTOM. ADVANCE MECHANIS 105683-0170

6. COUPLING PLATE 105663-0570

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105110-7040

11. Nozzle and Holder 16600-97078

12. Open Pre:MPa(Kqf/cm2) 17.7{180}/22.6{230}

13. NOZZLE-HOLDER 105041-4020

14. NOZZLE 105015-9240

15. NOZZLE SET

Include in #1:

106871-5122 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106871-5122 1068715122

Zexel num

Bosch num

Firm num

Name

106871-5122

INJECTION-PUMP ASSEMBLY
14CD PE8P PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-7-5- 4-3-6-2

Pre-stroke mm 3.9 3.85 3.95

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-5 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-3 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-6 deg. 270 269.5 270.5

Difference between angles 7
Cyl.1-2 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point A

Rack position 10.7

Pump speed r/min 650 650 650

Average injection quantity mm3/st. 144 143 145

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point E

Rack position 6.2+-0.5

Pump speed r/min 235 235 235

Average injection quantity mm3/st. 9.5 7.5 11.5

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Timer adjustment

Pump speed r/min 700

Advance angle deg. 0.3

Timer adjustment_02

Pump speed r/min (780)

Advance angle deg. 1 0.7 1.3

Remarks
Measure the actual speed.

Timer adjustment_03

Pump speed r/min -

Advance angle deg. 1 0.7 1.3

Remarks
Measure the actual speed.

Timer adjustment_04

Pump speed r/min 1100

Advance angle deg. 6 5.7 6.3

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Excess fuel setting for starting: SXL (5)Damper spring setting (6)Variable speed specification: idling adjustment (7)Fix the lever at the full-load position at delivery. (8)Main spring setting
----------
RT=1 TH=2.1mm SXL=11.2+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Pump speed = aa (2)Set the stopper bolt (fixed at full-load position at delivery.)
----------
aa=290r/min
----------
a=12deg+-5deg b=7.5deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting (2)Use the hole at R = aa
----------
aa=64.3mm
----------
a=18.5deg+-5deg b=29deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Drive side (2)Use the pin at R = aa
----------
aa=28mm
----------
a=12deg+-5deg b=64deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of the coupling's key groove at the beginning of injection of the No. 8 cylinder. (3)- (4)-
----------

----------
a=(90deg)

Information:

Introduction
The Environmental Protection Agency (EPA) has mandated that a DEF quality sensor must be installed on certain engines built after 2016. This new DEF quality sensor is integrated into the DEF header inside the DEF tank. The new style DEF header utilizes CAN C communication, so the wiring to the DEF header has been slightly modified on product going forward. However, the Dosing Control Unit (DCU) remains compatible to both setups with the latest engine software. ( 507-7605 Engine Software (24V DCU) or 507-7546 Engine Software (12V DCU)). As part of the DEF quality sensor implementation, a new configuration parameter setting is used on the engine Electronic Control Module (ECM) in Cat ET to identify whether a DEF quality sensor is"installed" or "not installed". Below are some different diagnostic codes for incompatible hardware and configuration setting as well as different service scenarios that may be encountered with this change and how to resolve any issues in these particular service scenarios. In addition to this Special Instruction, there is a video detailing these changes posted on Cat Channel 1.Diagnostic Codes When Parts/Settings Are Not Compatible
DEF quality header not installed but configuration set to "installed".
Table 1
J1939 Code and Description CDL Code and Description
1235-9
J1939 Network #3 : Abnormal Update Rate 5856-9
J1939 Network #3 : Abnormal Update Rate DEF quality header installed but configuration set to not installed.
Table 2
J1939 Code and Description CDL Code and Description
1761-3
Aftertreatment 1 Diesel Exhaust Fluid Tank Level : Voltage Above Normal 3130-3
Aftertreatment #1 SCR Catalyst Reagent Tank #1 Level Sensor : Voltage Above Normal
3031-3
Aftertreatment 1 Diesel Exhaust Fluid Tank Temperature : Voltage Above Normal 3134-3
Aftertreatment #1 SCR Catalyst Reagent Tank #1 Temperature Sensor : Voltage Above Normal DEF Quality Sensor Service Scenarios
Replacement Industrial Engine (2016 and earlier builds)
Replace with new engine (old engine no longer serviceable). Update to DEF quality sensor by installing a new DEF header, wiring harness, and DCU software and changing DEF quality sensor configuration status to "installed" in Cat ET.Replacement Machine Engine (2016 and Earlier Builds)
Replace with older service replacement Engine Arrangement Complete (EAC) engine (no other changes needed, confirm that DEF quality sensor configuration is set to "not installed" in CAT ET).
If dealer orders new EAC, update to DEF quality sensor is required (below scenario).Replacement Engine (2017and Future Builds)
Replace with latest EAC engine.Install DEF Quality Sensor on 2016 or Earlier Builds
Requires DCU software update, Pump, Electronic, and Tank Unit (PETU) wiring harness update, change DEF quality sensor configuration status to"installed".Replace DCU
No effect - new DCU hardware and software is compatible to both DEF headers.Replace Engine ECM
No effect when using ECM replacement file.
If engine ECM is replaced without the ECM replacement file, the DEF quality sensor configuration setting will default to "not installed" and may need to be updated if machine utilizes DEF quality sensor (requires Factory Passwords to change).Replace Wiring Harness
No effect - both new and old harness part numbers are available. Order same part number that is removed.