106871-2290 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068712290 me066326

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106871-2290 1068712290

MITSUBISHI ME066326 me066326

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-2290 zexel genuine, new aftermarket engine parts with delivery

Service parts 106871-2290 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106087-5351

3. GOVERNOR 105306-0750

4. SUPPLY PUMP 105207-1140

5. AUTOM. ADVANCE MECHANIS 105636-0770

6. COUPLING PLATE 105663-0260

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-5530

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 17.7(180)/21.6(220)

13. NOZZLE-HOLDER 105031-4500

14. NOZZLE

105015-5070

15. NOZZLE SET

Include in #1:

106871-2290 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106871-2290 1068712290

MITSUBISHI ME066326 me066326

Zexel num

Bosch num

Firm num

Name

106871-2290

ME066326 MITSUBISHI

INJECTION-PUMP ASSEMBLY
8DC9 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-7-3- 4-5-6-8

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cyl.1-2 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-3 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-5 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-6 deg. 270 269.5 270.5

Difference between angles 7
Cal 1-8 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point -

Rack position 10.7

Pump speed r/min 700 700 700

Each cylinder's injection qty mm3/st. 130 126.1 133.9

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point C

Rack position 6.7+-0.5

Pump speed r/min 200 200 200

Each cylinder's injection qty mm3/st. 18.5 15.7 21.3

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R3(10.7)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 130 129 131

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R2(10.4)

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 130 124.8 135.2

Difference in delivery mm3/st. 10.4 10.4 10.4

Fixing the lever *

Timer adjustment

Pump speed r/min 950--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 900

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1000

Advance angle deg. 1.8 1.1 2.5

Timer adjustment_04

Pump speed r/min 1100

Advance angle deg. 3.5 3.5

Timer adjustment_05

Pump speed r/min 1150

Advance angle deg. 6.5 6 7

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Rack limit using stop lever: RA (2)Excess fuel setting for starting: SXL (3)Rack difference between N = N1 and N = N2 (4)Beginning of damper spring operation: DL
----------
RA=13+0.2mm SXL=R1+0.2mm N1=1100r/min N2=600r/min DL=5-0.5mm
----------

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=15deg+-5deg b=19deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Using reverse lever (top)
----------

----------
a=20deg+-6deg b=39deg+-6deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=6.3mm
----------

Information:

TECHNICAL INFORMATION BULLETIN JAN. 15th, 2003
EXCAVATORS
WHEEL LOADERS
ENGINES 322C: (EMR, MAR);
325C: (CRB, CSJ, JLC, JLD, DTF)
950G II: (AYL, AYB);
962G II: (AYE, BAB)
3126B: (BMA)
Component Code(s) 1408SUBJECT: A NEW INJECTION ACTUATION PRESSURE CONTROL VALVE CONNECTOR INCREASES ENGINE OPERATION
PROBLEM:
The injection actuation pressure (IAP) control valve connector may have been assembled incorrectly on some 3126B engine harnesses. This can lead to intermittent engine operation or can cause the engine to stop.
SOLUTION:
If your machine exhibits symptoms of intermittent engine operation or abruptly stopping, the IAP control valve connector should be disconnected from the machine, examined for solenoid contact problems and re-installed using a correct procedure.
Procedure for installing the IAP control valve connector
This procedure will describe how to properly install the 232-4367 Harness.
Required Parts
Qty Part Number Description
1 232-4367 Harness
Procure the part that is listed in the table.
Illustration 1. Left Side of a 3126B Engine on a D6N.
(1) IAP Control Valve
(2) IAP Control Valve Connector
Note: Illustration 1 is from a D6N that is equipped with a 3126B for photographical purposes. The location of the IAP Control Valve is the same for your machine.
Disconnect the IAP control valve connector (2) from the IAP Control Valve (1). See Illustration 1.
Cut the two wires directly behind the connector.
Using wire strippers, strip the ends of the two wires.
Install the 232-4367 Harness, by crimping the stripped wires inside the splice.
Note: Take care to connect the pink wire to the pink wire on one hand and the purple wire to the purple wire on the other hand.
Heat both heat shrinkable tubes in order to insulate both the splices.
Reconnect the repaired harness to the IAP Control Valve (1).
COPYRIGHT 2003 CATERPILLAR
ALL RIGHTS RESERVED