106693-6060 ZEXEL 9 400 617 926 BOSCH INJECTION-PUMP ASSEMBLY 9400617926 1066936060 1156027330


 

Information injection-pump assembly

BOSCH 9 400 617 926 9400617926
ZEXEL 106693-6060 1066936060
ISUZU 1156027330 1156027330
106693-6060 INJECTION-PUMP ASSEMBLY
Rating:
15
Buy INJECTION-PUMP ASSEMBLY 106693-6060 zexel genuine, new aftermarket engine parts with delivery

Service parts 106693-6060 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106069-1350
3. GOVERNOR 105407-3440
4. SUPPLY PUMP 105237-1430
5. AUTOM. ADVANCE MECHANIS 105636-1530
6. COUPLING PLATE 105663-0250
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-6991
11. Nozzle and Holder 1-15300-159-0
12. Open Pre:MPa(Kqf/cm2) 19.6(200)
13. NOZZLE-HOLDER 105030-4271
14. NOZZLE 105015-6660
15. NOZZLE SET

Include in #1:

106693-6060 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 617 926 9400617926
ZEXEL 106693-6060 1066936060
ISUZU 1156027330 1156027330


Zexel num
Bosch num
Firm num
Name
106693-6060 
9 400 617 926 
1156027330  ISUZU
INJECTION-PUMP ASSEMBLY
6RB1-T K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-1920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3 2.97 3.03
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   A
Rack position   R1(7.6)
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   117.7 115.7 119.7
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   4.5+-0.5
Pump speed r/min   325 325 325
Average injection quantity mm3/st.   8.6 5.4 11.8
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Injection quantity adjustment_03
Adjusting point   D
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   210 210
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   775--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   725
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   900
Advance angle deg.   1.5 1 2
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106693-6060
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)RACK LIMIT (3)Set idle sub-spring (4)Main spring setting (5)Rack difference between N = N1 and N = N2
----------
K=11 N1=900r/min N2=700r/min
----------

Speed control lever angle

Test data 106693-6060
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(3deg)+-5deg b=(21deg)+-5deg

Stop lever angle

Test data 106693-6060
N:Pump normal S:Stop the pump.
----------

----------
a=10deg+-5deg b=53deg+-5deg

Timing setting

Test data 106693-6060
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------

----------
a=(70deg)




Information:

Cautions Regarding Battery* Handle Battery Carefully * Never use flames or allow sparks near the battery. The battery releases flammable hydrogen gas and oxygen gas. These gases can be ignited by flames and cause an explosion.* Do not use the battery when the fluid surface is lower than the minimum level. Using a battery with a low electrolyte level can result in an explosion.* Do not short the battery terminals with a tool or other metal object.* When disconnecting battery cables, always remove the cable from the negative (-) terminal first. When reconnecting cables, attach the cable to the positive (+) terminal first.* Charge the battery in a well-ventilated area, with all filling hole plugs removed.* Make sure the cable clamps are securely installed on the battery terminals. A loose cable clamp can cause sparks that may result in explosion.* Before servicing electrical components or conducting electrical welding, set the battery switch to the [Open/OFF] position or disconnect the cable from the negative (-) battery terminal to cut off the electrical current.* Electrolyte (battery fluid) contains dilute sulfuric acid. Careless handling of the battery can lead to the loss of sight and/or burns. Also, do not swallow electrolyte.* Wear protective goggles and rubber gloves when maintaining and inspecting the battery (when adding water, charging, etc.).* If electrolyte is spilled onto the skin or clothes, immediately wash with lots of clean fresh water and thoroughly clean with soap.* If electrolyte gets into eyes, immediately flush with lots of clean fresh water and seek immediate medical attention.* Should you accidentally swallow electrolyte, gargle with plenty of water, then drink lots of water, and seek immediate medical attention.
Response To Abnormalities* If Engine Overheats, Conduct Heating Operation Before Stopping The Engine If the engine overheats, do not stop the engine immediately. Abruptly stopping an overheated engine may cause the coolant temperature to rise, resulting in seizing of the engine. If the engine overheats, operate the engine at low idling speed (cooling temperature), and stop the engine after the coolant temperature lowers sufficiently.Do not add coolant immediately after stopping the engine. Adding coolant to a hot engine may cause damage to the cylinder heads due to sudden change in temperature. Add coolant after the engine cools to room temperature.* If Engine Stops Due To Abnormality, Exercise Caution When Restarting If the engine stops due to an abnormality, do not restart the engine immediately. If the engine stops with an alarm, check and correct the cause of the problem before restarting. Operating the engine without correcting the problem may result in serious engine problems.* If Oil Pressure Drops, Stop Engine Immediately If the engine oil pressure decreases, stop the engine immediately, and inspect the lubrication system. Operating the engine with low oil pressure may cause seizing of the bearings and other parts.* If Fan Belt Breaks, Stop Engine Immediately If the fan belt breaks, stop the engine immediately. Continued operation of the engine without the fan belt causes coolant to change to steam and

Have questions with 106693-6060?





Group cross 106693-6060 ZEXEL

Isuzu 

 
1156026181 
INJECTION-PUMP ASSEMBLY
6QB2
 
1156026182 
INJECTION-PUMP ASSEMBLY
6QB2
 
1156026183 
INJECTION-PUMP ASSEMBLY
6QB2
 
1156026184 
INJECTION-PUMP ASSEMBLY
6QB2
9 400 617 920 
1156026185 
INJECTION-PUMP ASSEMBLY
6QB2
 
1156026190 
INJECTION-PUMP ASSEMBLY
6QB2
 
1156026191 
INJECTION-PUMP ASSEMBLY
6QB2
 
1156026192 
INJECTION-PUMP ASSEMBLY
6QB2
F 019 Z10 435 
1156026193 
INJECTION-PUMP ASSEMBLY
6QB2
9 400 617 921 
1156026194 
INJECTION-PUMP ASSEMBLY
6QB2
 
1156026660 
INJECTION-PUMP ASSEMBLY
6SD1-TC1
9 400 617 922 
 
INJECTION-PUMP ASSEMBLY
6SD1-TC1

Isuzu 

9 400 617 922 
1156026661 
INJECTION-PUMP ASSEMBLY
6SD1-TC1
 
1156026670 
INJECTION-PUMP ASSEMBLY
6SD1-TC1
 
1156026671 
INJECTION-PUMP ASSEMBLY
6SD1-TC1
9 400 617 923 
1156026672 
INJECTION-PUMP ASSEMBLY
6SD1-TC1
 
1156026680 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
 
1156026681 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
9 400 617 924 
1156026682 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
 
1156026690 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
 
1156026691 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
9 400 617 925 
 
INJECTION-PUMP ASSEMBLY
6SD1-TC3

Isuzu 

9 400 617 925 
1156026692 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
106693-6060  
9 400 617 926 
1156027330 
INJECTION-PUMP ASSEMBLY
6RB1-T
 
1156027440 
INJECTION-PUMP ASSEMBLY
6SD1-TC1
9 400 617 927 
1156027441 
INJECTION-PUMP ASSEMBLY
6SD1-TC1
 
1156027460 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
9 400 617 928 
1156027461 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
 
1156026120 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
9 400 617 929 
1156026121 
INJECTION-PUMP ASSEMBLY
6SD1-TC3
Back to top