106692-9150 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066929150

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106692-9150 1066929150

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106692-9150 zexel genuine, new aftermarket engine parts with delivery

Service parts 106692-9150 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106069-7210

3. GOVERNOR 105407-2520

4. SUPPLY PUMP 105217-1390

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-4750

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 22.6{230}

13. NOZZLE-HOLDER 105031-4220

14. NOZZLE

105015-3250

15. NOZZLE SET

Include in #1:

106692-9150 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106692-9150 1066929150

Zexel num

Bosch num

Firm num

Name

106692-9150

INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131424-1520

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 2.9 2.85 2.95

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 11.4

Pump speed r/min 900 900 900

Each cylinder's injection qty mm3/st. 202 198 206

Basic *

Fixing the rack *

Injection quantity adjustment_02

Adjusting point B

Rack position 5.4+-0.5

Pump speed r/min 200 200 200

Each cylinder's injection qty mm3/st. 20.5 18.4 22.6

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Set idle sub-spring (4)Confirm that the rack is pulled back to R = R1 or less at solenoid operation (N = 0).
----------
K=10 R1=4.9mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting (2)Stopper bolt setting (3)Set the pump speed at aa (4)Set the pump speed at bb.
----------
aa=750r/min bb=900r/min
----------
a=18deg+-5deg b=33deg+-5deg c=8deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=20deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of key groove at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(50deg)

Information:

Table 1
Revision Summary of Changes
02 Added serial number prefixes Description Of Change: An updated Diesel Exhaust Fluid (DEF) control unit software is now used on the machine engines listed above. The updated software has been released to improve the priming performance of the DEF pumps in cold environments.Adaptable To:
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
The following changes are adaptable to the products within the listed serial numbers, and are effective with all products after the listed serial numbers.The new and former part numbers are listed in Table 2.
Table 2
Required Parts
Qty Dosing Control Unit (DCU) Dosing Control Unit (DCU) Voltage New Part Number Part Name Former Part Number(1)
1 Restriction on Hazardous Substance (RoHS) (DCU) 24V 593-7031 Engine Software 567-5763
1 Restriction on Hazardous Substance (RoHS) (DCU) 12V 593-7030 Engine Software 567-5761
1 Non-Restriction on Hazardous Substance (RoHS) (DCU) 24V 593-7033 Engine Software 539-3577
1 Non-Restriction on Hazardous Substance (RoHS) (DCU) 12V 593-7032 Engine Software 539-3576
(1) The former part number listed is for reference only and may differ.The new software is available in the form of a flash file through the Cat ® Service Information System (SIS). A newer part number may be available. SIS Web only displays the latest available flash file.