106691-1960 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1066911960 9812011723


 

Information injection-pump assembly

ZEXEL 106691-1960 1066911960
ISUZU 9812011723 9812011723
106691-1960 INJECTION-PUMP ASSEMBLY
Rating:
75
Buy INJECTION-PUMP ASSEMBLY 106691-1960 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
106691-1960 
106691-1961 
 
9812011723  ISUZU
INJECTION-PUMP ASSEMBLY
E120 *




Information:


Illustration 1 g00564355
7W-2743 Electronic Speed Switch (ESS)
(1) Push button for Overspeed Verification
(2) Reset button
(3) Overspeed indicator lamp
(4) Seal screw plug for adjusting the engine overspeed
(5) Seal screw plug for adjusting the crank terminate speed
(6) Seal screw plug for adjusting the oil step pressure speed setting The procedure for the magnetic pickup test will determine if the operation of the magnetic pickup is correct.
Connect a 6V-7070 Digital Multimeter to the "COM" terminal and the "SIG" terminal. The terminals are (ESS-3)and (ESS-4) of the ESS. Set the meter voltage scale to a scale that is greater than 1.5 VAC. Start the engine. Run the engine at low idle or 600 rpm. Choose the one that is larger. If the voltage that is measured is 1.5 VAC or more, the operation of the magnetic pickup is correct. If the voltage is less than 1.5 VAC, go to Step 2.
Stop the engine. Disconnect the wiring for the magnetic pickup at the plug-in connector. Connect the voltmeter to the connector terminals of the magnetic pickup. Start the engine. Run the engine at low idle or 600 rpm. Choose the one that is larger. If the voltage that is measured is 1.5 VAC or more, repair the wiring that is between the magnetic pickup and the ESS. If the voltage is less than 1.5 VAC, go to Step 3.
Illustration 2 g00564913
Magnetic pickup
(1) Clearance
(2) Magnetic pickup
(3) Wires to the connector
(4) Locknut
(5) Flywheel housing
(6) Ring gear
Loosen locknut (4) and turn magnetic pickup (2) in the counterclockwise direction in order to remove magnetic pickup (2) from flywheel housing (5). Turn the flywheel until a gear tooth of ring gear (6) is directly in the center of the threaded hole for magnetic pickup (2). Install magnetic pickup (2) in flywheel housing (5).
Turn magnetic pickup (2) in the clockwise direction until the end of magnetic pickup (2) slightly touches the gear tooth. Turn the magnetic pickup for one-half turn in the counterclockwise direction in order to set correct clearance (1). Tighten locknut (4) to a torque of 45 7 N m (33 5 lb ft). Note: Do not allow the magnetic pickup to turn while the locknut is tightened.
Repeat Step 2. If the voltage is still less than 1.5 VAC, replace the magnetic pickup.

Have questions with 106691-1960?





Group cross 106691-1960 ZEXEL

Isuzu 

 
1156001272 
INJECTION-PUMP ASSEMBLY
E120
9 400 617 771 
1156007331 
INJECTION-PUMP ASSEMBLY
E120
 
1156007371 
INJECTION-PUMP ASSEMBLY
E120
9 400 610 183 
1156007381 
INJECTION-PUMP ASSEMBLY
E120
 
9812011121 

E120
9 400 617 772 
9812011203 
INJECTION-PUMP ASSEMBLY
E120
106691-1960  

106691-1961 
 
9812011723 
INJECTION-PUMP ASSEMBLY
E120
9 400 619 810 
9812011724 
INJECTION-PUMP ASSEMBLY
E120
9 400 617 773 
1156007350 
INJECTION-PUMP ASSEMBLY
E120
 
1156001671 

E120
 
1156001851 

E120
Back to top