Information injection-pump assembly
BOSCH
9 400 619 873
9400619873
ZEXEL
106682-9530
1066829530
Rating:
Service parts 106682-9530 INJECTION-PUMP ASSEMBLY:
1.
_
5.
AUTOM. ADVANCE MECHANIS
7.
COUPLING PLATE
8.
_
9.
_
11.
Nozzle and Holder
12.
Open Pre:MPa(Kqf/cm2)
24.5{250}
15.
NOZZLE SET
Include in #1:
106682-9530
as INJECTION-PUMP ASSEMBLY
Cross reference number
BOSCH
9 400 619 873
9400619873
ZEXEL
106682-9530
1066829530
Zexel num
Bosch num
Firm num
Name
Calibration Data:
Adjustment conditions
Test oil
1404 Test oil ISO4113 or {SAEJ967d}
1404 Test oil ISO4113 or {SAEJ967d}
Test oil temperature
degC
40
40
45
Nozzle and nozzle holder
105780-8130
Bosch type code
EFEP215A
Nozzle
105780-0050
Bosch type code
DN6TD119NP1T
Nozzle holder
105780-2090
Bosch type code
EFEP215
Opening pressure
MPa
17.2
Opening pressure
kgf/cm2
175
Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-4-1000
Outer diameter - inner diameter - length (mm) mm 8-4-1000
Overflow valve
131425-1620
Overflow valve opening pressure
kPa
255
221
289
Overflow valve opening pressure
kgf/cm2
2.6
2.25
2.95
Tester oil delivery pressure
kPa
157
157
157
Tester oil delivery pressure
kgf/cm2
1.6
1.6
1.6
Direction of rotation (viewed from drive side)
Right R
Right R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right R
Right R
Injection order
1-5-3-6-
2-4
Pre-stroke
mm
3
2.95
3.05
Beginning of injection position
Drive side NO.1
Drive side NO.1
Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5
Cal 1-5 deg. 60 59.5 60.5
Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5
Cal 1-3 deg. 120 119.5 120.5
Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5
Cal 1-6 deg. 180 179.5 180.5
Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5
Cyl.1-2 deg. 240 239.5 240.5
Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5
Cal 1-4 deg. 300 299.5 300.5
Injection quantity adjustment
Adjusting point
A
Rack position
13.8
Pump speed
r/min
900
900
900
Average injection quantity
mm3/st.
409
404
414
Max. variation between cylinders
%
0
-3
3
Basic
*
Fixing the rack
*
Remarks
Standard point A's rack position same as row R
Standard point A's rack position same as row R
Injection quantity adjustment_02
Adjusting point
C
Rack position
7.2+-0.5
Pump speed
r/min
400
400
400
Average injection quantity
mm3/st.
20
18.5
21.5
Max. variation between cylinders
%
0
-15
15
Fixing the rack
*
Test data Ex:
Governor adjustment
N:Pump speed
R:Rack position (mm)
(1)Target notch: K
(2)Tolerance for racks not indicated: +-0.05mm.
(3)RACK LIMIT for 106684-4251
(4)Idle sub spring setting: L1.
----------
K=21 L1=7.2-0.5mm
----------
----------
K=21 L1=7.2-0.5mm
----------
Speed control lever angle
F:Full speed
I:Idle
(1)Set the pump speed at aa. ( At delivery )
(2)Set the pump speed at bb.
(3)Stopper bolt setting
(4)Stopper bolt setting
(5)Actual measurement
(6)Actual measurement
(7)Actual measurement
----------
aa=900r/min bb=750r/min
----------
----------
aa=900r/min bb=750r/min
----------
Stop lever angle
N:Pump normal
S:Stop the pump.
(1)Pump speed aa and rack position bb (to be sealed at delivery)
(2)No return spring
----------
aa=0r/min bb=1-0.5mm
----------
a=(73deg) b=43.5deg+-5deg
----------
aa=0r/min bb=1-0.5mm
----------
a=(73deg) b=43.5deg+-5deg
Timing setting
(1)Pump vertical direction
(2)Coupling's key groove position at No 1 cylinder's beginning of injection
(3)B.T.D.C.: aa
(4)-
----------
aa=20deg
----------
a=(30deg)
----------
aa=20deg
----------
a=(30deg)
Information:
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
The new and former rocker arm base assembly is listed in Table 1.Note: The 568-8215 Rocker Arm Base As has the following serviceable components.
Table 1
Required Parts
Qty New Part Number Part Name Former Part Number(1)
1 568-8215 Rocker Arm Base As 121-2024
2 261-0195 Hollow Dowel 8N-4387
1 567-2901 Spacer N/A
1 567-2902 Spacer N/A
3 6V-6228 O-Ring Seal N/A
1 240-7032 Seal N/A
(1) The former part number listed is for reference only and may differ.
Illustration 1 g06562147
(1) 567-2901 Spacer
(2) 6V-6228 O-Ring Seal
(3) 567-2902 Spacer
Illustration 2 g06562161
(4) 240-7032 Seal
(5) 261-0195 Hollow Dowel
Illustration 3 g06562155
(6) 568-8215 Rocker Arm Base As
(7) 121-2024 Base AsNote: Refer to the Illustration 3 to see the differences between the new and former designs.