106682-9401 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066829401

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106682-9401 1066829401

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106682-9401 zexel genuine, new aftermarket engine parts with delivery

Service parts 106682-9401 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106068-2890

3. GOVERNOR 105447-1741

4. SUPPLY PUMP 105237-1541

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-0390

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105111-4640

11. Nozzle and Holder 6162-15-3100

12. Open Pre:MPa(Kqf/cm2) 26.0{265}

13. NOZZLE-HOLDER 105041-7140

14. NOZZLE 105025-0870

15. NOZZLE SET

Include in #1:

106682-9401 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106682-9401 1066829401

Zexel num

Bosch num

Firm num

Name

106682-9401

INJECTION-PUMP ASSEMBLY
14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8130

Bosch type code EFEP215A

Nozzle 105780-0050

Bosch type code DN6TD119NP1T

Nozzle holder 105780-2090

Bosch type code EFEP215

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-4-1000

Overflow valve 131425-1620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 2.8 2.75 2.85

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 14

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 505 500 510

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Boost pressure kPa 60 60

Boost pressure mmHg 450 450

Injection quantity adjustment_02

Adjusting point C

Rack position 6.8+-0.5

Pump speed r/min 365 365 365

Average injection quantity mm3/st. 12.5 7.5 17.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Boost compensator adjustment

Pump speed r/min 600 600 600

Rack position R1-3.4

Boost pressure kPa 6.7 4 9.4

Boost pressure mmHg 50 30 70

Boost compensator adjustment_02

Pump speed r/min 600 600 600

Rack position R1(14.5)

Boost pressure kPa 46.7 40 53.4

Boost pressure mmHg 350 300 400

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Boost compensator stroke: BCL (3)Rack difference between N = N1 and N = N2
----------
K=20 BCL=3.4+-0.1mm N1=850r/min N2=650r/min
----------

Speed control lever angle

F:Full speed I:Idle S:Stop (1)Use the hole at R = aa
----------
aa=90mm
----------
a=18deg+-5deg b=24deg+-5deg c=52deg+-3deg

0000001501 LEVER

1. Adjustment of the control lever (1)Perform idling with the speed lever (a) contacting the pushrod (b) At this time, confirm that the spring (c) is not compressed by speed lever (a)'s operating torque. (2)To set the stop position, compress spring (c) using the speed lever (a) and adjust the rack so that it contacts the guide screw at position L1. Then, set and fix using the lock nut (e). Adjust rack position at this time using shim (f). (3)After pulling the speed lever (a) in the stop direction and releasing it, confirm that it returns to the idle position.
----------
L1=0.2~2mm
----------

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(40deg)

Information:

2. Remove bolts (1) from the alternator bracket.3. Remove the bolts that hold plate (3), and remove the plate.4. Disconnect water line (2) from the air compressor. Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 5. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.6. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
7. Remove the gasket, seals (6) and O-ring seals (7) from the spacer plate. The following steps are for installation of the cylinder head. Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate.8. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (6) and two O-ring seals (7).9. Fasten a hoist, and put the cylinder head assembly in position on the cylinder block. 10. Put Loctite Nickel Anti-Seize on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown.a. Tighten bolts 1 through 14 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 14 in number sequence to a torque of 470 20 N m (345 15 lb.ft.).c. Tighten bolts 1 through 14 in number sequence to a torque of 470 20 N m (345 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 15 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 15 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 15 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the bolts (5) to a torque of 45 7 N m (33 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 35 5 N m (26 3 lb.ft.).11. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).12. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.13. Install the valve covers. See Install Valve Covers.14. Install plate (3).15. Connect water line (2) to the air compressor.16. Install bolts (1) for the alternator bracket.17. Install the intake manifold on the