106682-4632 ZEXEL F 019 Z10 874 BOSCH INJECTION-PUMP ASSEMBLY f019z10874 1066824632 35a6510360


 

Information injection-pump assembly

BOSCH F 019 Z10 874 f019z10874
ZEXEL 106682-4632 1066824632
MITSUBISHI-HEAV 35A6510360 35a6510360
106682-4632 INJECTION-PUMP ASSEMBLY
Rating:
13
Buy INJECTION-PUMP ASSEMBLY 106682-4632 zexel genuine, new aftermarket engine parts with delivery

Service parts 106682-4632 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106068-2981
3. GOVERNOR 105447-0880
4. SUPPLY PUMP 105237-1690
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105664-0670
7. COUPLING PLATE 156638-2420
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6220
11. Nozzle and Holder 35A6100010
12. Open Pre:MPa(Kqf/cm2) 21.6(220)
13. NOZZLE-HOLDER 105030-4320
14. NOZZLE 105015-8520
15. NOZZLE SET

Include in #1:

106682-4632 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
106682-4632 
106682-4633 
F 019 Z10 874 
35A6510360  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S6A3 * K




Information:

The problems in this section are problems that do come about and are normally called "low power." These problems are not necessarily more common than engine problems, but they are possible problems which you need to read and check before an engine is disassembled.Read all of the items but make sure the first three are checked completely before making any engine test. Possible Causes/CorrectionsTachometer Error
To check, connect a tachometer of known accuracy to the engine. Run the engine and make a comparison of the readings of the vehicle and test tachometers. If vehicle tachometer is bad, make repairs as necessary or install a new tachometer.Engine Operated at High Altitude
Less oxygen at higher altitudes causes the engine horsepower to go down. There is no effect on the horsepower of the engine for the first 2280 m (7500 ft) above sea level of operation.Brakes Do Not Completely Release
Check the brakes by feeling all the brake drums. If the brakes of a wheel do not completely release, the brake drum for that wheel will be hotter than the brake drums for the other wheels. With the truck lifted with a jack, the wheels must have free rotation when turned by hand.Extra Engine Driven Equipment
Air compressors, hydraulic pumps, alternator, and other engine driven equipment that has damage, or that was not installed correctly, or that is not in correct adjustment, can take more horsepower to drive than expected. If necessary, disconnect the equipment and test the engine.Speedometer Error
A bad speedometer does not give the correct speed or the correct indication of fuel consumption. An indication of low speed can cause the operator to feel that he has a power problem.Speeds Too High
The need for more horsepower is easy to see as the speed of the vehicle is increased. This is especially true if the front of the vehicle has a large surface area. Application personnel can give you the horsepower necessary for different vehicle designs at different speeds.Overload On Vehicle
Application personnel can give you the horsepower needs for different vehicles.High Moving Resistance
Soft ground conditions cause a need for more horsepower. To see if the problem is the engine, test the vehicle on a surface known to be good, or test on a chassis dynamometer.High Wind Resistance
The horsepower needs for a truck can be divided into two parts. Part of the horsepower is used to move the vehicle and part is used to get through the resistance of the wind. The horsepower necessary to get through the resistance of the wind will increase as the vehicle is used at higher speeds. Vehicles with large front area have a higher wind resistance and take more horsepower than those with a small front area. Some types of trucks, for example those used for the transportation of automobiles and or boats have high wind resistance even if the front area is small. Moving against the wind has the same effect on wind resistance as does higher vehicle speed.Power Loss in Drive Gears
It is possible for a

Have questions with 106682-4632?





Group cross 106682-4632 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 565 
6212711860 
INJECTION-PUMP ASSEMBLY
SA6D140
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 566 
6212711870 
INJECTION-PUMP ASSEMBLY
SA6D140
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 567 
6212711880 
INJECTION-PUMP ASSEMBLY
SA6D140

Mitsubishi-Heav 

 
35A6500360 
INJECTION-PUMP ASSEMBLY
S6A3
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi-Heav 

106682-4632  

106682-4633 
F 019 Z10 874 
35A6510360 
INJECTION-PUMP ASSEMBLY
S6A3
9 400 612 925 
35A6520360 
INJECTION-PUMP ASSEMBLY
S6A3
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi-Heav 

 
35A6510330 
INJECTION-PUMP ASSEMBLY
S6A3
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi-Heav 

9 400 610 971 
35A6520330 
INJECTION-PUMP ASSEMBLY
S6A3
9 400 611 841 
35A6530330 
INJECTION-PUMP ASSEMBLY
S6A3
9 400 612 573 
35A6540330 
INJECTION-PUMP ASSEMBLY
S6A3
 
35A6550330 
INJECTION-PUMP ASSEMBLY
S6A3
9 400 613 213 
35A6560330 
INJECTION-PUMP ASSEMBLY
S6A3
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 568 
6162732410 
INJECTION-PUMP ASSEMBLY
SA6D170
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 569 
6162732420 
INJECTION-PUMP ASSEMBLY
SA6D170
F 019 Z10 056 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 057 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 570 
6162732160 
INJECTION-PUMP ASSEMBLY
S6D170

Shinko-Engin. 

9 400 617 571 
0170095400 
INJECTION-PUMP ASSEMBLY
S12V15D
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 572 
6162732440 
INJECTION-PUMP ASSEMBLY
SA6D170
Back to top