106676-2700 ZEXEL 9 400 613 211 BOSCH INJECTION-PUMP ASSEMBLY 9400613211 1066762700 me441598


 

Information injection-pump assembly

BOSCH 9 400 613 211 9400613211
ZEXEL 106676-2700 1066762700
MITSUBISHI ME441598 me441598
106676-2700 INJECTION-PUMP ASSEMBLY
Rating:
33
Buy INJECTION-PUMP ASSEMBLY 106676-2700 zexel genuine, new aftermarket engine parts with delivery

Service parts 106676-2700 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-0470
3. GOVERNOR 105407-8280
4. SUPPLY PUMP 105207-1200
5. AUTOM. ADVANCE MECHANIS 105681-4370
6. COUPLING PLATE 105663-0910
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-7110
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}
13. NOZZLE-HOLDER 105031-4530
14. NOZZLE 105015-6150
15. NOZZLE SET

Include in #1:

106676-2700 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
106676-2700 
9 400 613 211 
ME441598  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D24T K 14CA INJECTION PUMP ASSY PE6P,6PD PE




Information:


Be sure all timing pins and bolts have been removed from timing holes before turning the crankshaft.
2. Remove the nuts and cap from the connecting rod. Push the piston and connecting rod up until the piston rings are out of cylinder liner. 3. Remove the connecting rod and piston (1) from engine. Keep the caps and bearings with their respective connecting rods.Install Pistons
1. Turn the crankshaft so the bearing journal is at bottom center for piston being installed.2. Put clean engine oil on crankshaft journal, connecting rod bearings, and the piston rings. 3. Put compressor (A) on top of liner, and install the piston and connecting rod with the "V" mark on piston in alignment with "V" mark on spacer plate. Put the connecting rod in position on crankshaft while pushing piston into liner. 4. Put clean engine oil on threads of connecting rod bolts. Install the caps on connecting rods. Install and tighten nuts to 30 3 lb.ft. (4.1 0.4 mkg). Put a mark across the nuts and bolts; and turn nuts clockwise 90° from marks as shown.
Make sure the number mark on side of cap is the same number and on the same side as the number mark on side of connecting rod.
end by: a) install oil pumpb) install cylinder head assembly

Have questions with 106676-2700?





Group cross 106676-2700 ZEXEL

Mitsubishi 

106676-2700  
9 400 613 211 
ME441598 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 617 457 
ME441599 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 617 458 
ME441600 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 617 459 
ME441601 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 617 460 
ME441602 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 617 461 
ME441603 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 613 177 
ME441604 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 617 462 
ME441606 
INJECTION-PUMP ASSEMBLY
6D24TC
F 01G 09U 1HR 
ME441606 
INJECTION-PUMP ASSEMBLY
6D24TC
9 400 617 463 
ME441607 
INJECTION-PUMP ASSEMBLY
6D24TC
9 400 617 464 
ME441608 
INJECTION-PUMP ASSEMBLY
6D24TC
Back to top