106676-2601 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066762601

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106676-2601 1066762601

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106676-2601 zexel genuine, new aftermarket engine parts with delivery

Service parts 106676-2601 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106067-6620

3. GOVERNOR 105407-8110

4. SUPPLY PUMP 105207-1200

5. AUTOM. ADVANCE MECHANIS 105681-2790

6. COUPLING PLATE 105663-0550

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105110-7550

11. Nozzle and Holder ME158263

12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}

13. NOZZLE-HOLDER 105041-4130

14. NOZZLE

15. NOZZLE SET 105019-0700

Include in #1:

106676-2601 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106676-2601 1066762601

Zexel num

Bosch num

Firm num

Name

106676-2601

INJECTION-PUMP ASSEMBLY
14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131424-4620

Overflow valve opening pressure kPa 255 255 255

Overflow valve opening pressure kgf/cm2 2.6 2.6 2.6

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 8.6

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 93 91 95

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point Z

Rack position 6+-0.5

Pump speed r/min 650 650 650

Average injection quantity mm3/st. 16 13.4 18.6

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_03

Adjusting point C

Rack position 9.4++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 185 175 195

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 0

Advance angle deg. 2.5 2 3

Timer adjustment_02

Pump speed r/min 300

Advance angle deg. 2.5 2 3

Remarks
Start

Timer adjustment_03

Pump speed r/min -

Advance angle deg. 0 0 0

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Rack difference between N = N1 and N = N2
----------
K=12 N1=1000r/min N2=250r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=5deg+-5deg b=21deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Normal
----------

----------
a=19deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(6deg)

Information:

PROBLEM
The existing fuel injectors can experience injector failures due to injector body cracking. If the existing injector fails it can result in complaints of high oil levels due to excessive fuel dilution.
AFFECTED PRODUCT
Model Identification Number
C27 A6X00101-00105
EGG00100
NAR00100-00119
T4Z00100, 200-227, 236
C32 NST00100-00108
SDK00101-00198
PMC27 N1B00100-00105, 107-118, 120-126, 128
PARTS NEEDED
Qty
Part Number Description
2 1R1808 FILTER-LUBE
12 8S9191 BOLT
12 3594060 INJECTOR GP-FUEL
1 BULK_OIL DEO (Refer to the OMM for Refill Capacities)
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 2% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.
ACTION REQUIRED
If excessive fuel dilution of engine oil is found reference the following to determine the cause of fuel dilution.
Refer to Special Instruction, REHS3007, "Determining the Cause of Fuel Dilution of Engine Oil"
Troubleshooting C27 and C32 Engines:
UENR0505 C27 Petroleum Generator Set Engines
UENR0504 C27 and C32 Industrial Engines
KENR9192 C27 Generator Set Engines
Once an injector(s) has been identified as having a cracked/leaking injector body, replace the failed injector(s). Inspect the remaining good injector serial numbers with Cat ET, (Injector Serial Numbers = Injector trim file name, (ie 6Cxxxxxxxxxx.trm)). If the remaining injector serial numbers fall within the serial number range below, replace at the same time. Refer to Image 1 for the serial number location on the top of the electronic unit injector.
Injector Serial Numbers
6C001793971D through 6C002198297C
8S-9191 Injector Hold Down Bolt must be replaced.
Refer to Disassembly and Assembly, KENR8167 for the removal, installation, and tightening procedures.
After the engine is reassembled, change the engine oil and filters.
Image1
SERVICE CLAIM ALLOWANCES
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
0-3500 hrs,
0-24 mo 100.0% 100.0% 0.0% 0.0% 0.0% 0.0%
3501-6000 hrs,
25-48 mo 50.0% 50.0% 0.0% 0.0% 50.0% 50.0%
This is a 10.0-hour job
If there has been a previous repair, part age/hours will apply. Retain a copy of the previous repair invoice in the dealer's records for audit purposes, and specify repair date and machine hours in the "Additional Comments" section of the warranty claim.
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.