106676-2221 ZEXEL F 019 Z20 149 BOSCH INJECTION-PUMP ASSEMBLY f019z20149 1066762221 me442611

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH F 019 Z20 149 f019z20149

ZEXEL 106676-2221 1066762221

MITSUBISHI ME442611 me442611

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106676-2221 zexel genuine, new aftermarket engine parts with delivery

Service parts 106676-2221 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106067-1710

3. GOVERNOR 105407-6150

4. SUPPLY PUMP 105207-1200

5. AUTOM. ADVANCE MECHANIS 105681-2900

6. COUPLING PLATE 105663-0910

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105110-7511

11. Nozzle and Holder ME158200

12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}

13. NOZZLE-HOLDER 105041-4131

14. NOZZLE

15. NOZZLE SET 105019-0680

Include in #1:

106676-2221 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z20 149 f019z20149

ZEXEL 106676-2221 1066762221

MITSUBISHI ME442611 me442611

Zexel num

Bosch num

Firm num

Name

106676-2221

F 019 Z20 149

ME442611 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D24 K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131424-4620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 8.8

Pump speed r/min 750 750 750

Average injection quantity mm3/st. 94.5 91.5 97.5

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 8.5

Pump speed r/min 750 750 750

Average injection quantity mm3/st. 84.5 81.5 87.5

Fixing the rack *

Injection quantity adjustment_03

Adjusting point D

Rack position 4.8+-0.5

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 8.5 5.9 11.1

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_04

Adjusting point E

Rack position 10.5++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 100 90 110

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min (900)

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min -

Advance angle deg. 2 2 2

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Rack difference between N = N1 and N = N2 (5)Set idle sub-spring
----------
K=8 N1=750r/min N2=220r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Set the pump speed at aa. ( At delivery ) (2)When pump speed set at bb (3)Stopper bolt setting
----------
aa=900r/min bb=750r/min
----------
a=24deg+-5deg b=3deg+-5deg c=6deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)No return spring
----------

----------
a=48.5deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(5deg)

Information:

REM09-03
Reman
January 2009 CATERPILLAR REMAN ANNOUNCES AN APPEARANCE CHANGE TO CERTAIN MECHANICAL
UNIT FUEL INJECTORS
Announcement
The Caterpillar Reman Products Group introduces a new metal deposition process around the bracket for certain mechanical unit injectors. This new process will alter the appearance of the remanufactured mechanical unit injectors. Validation tests confirm the change will not alter quality, reliability, fit or performance.
Acceptable appearances with this new metal deposition process are as shown below (see figures 1 &2).
Effective January 2009, this appearance change will affect the following part numbers:
Features And Benefits
Cat? Reman Fuel Injectors offer excellent value to customers. Customers who want fast repair turn-around, superior quality and reliability, and lower repair costs will benefit from the use of these remanufactured fuel injectors. Cat Reman Fuel Injectors provide immediate, off-the-shelf availability at a fraction of the new price.
Core Acceptance
The Core Acceptance Criteria for Caterpillar Reman Fuel Injectors is simple, visual, and does not require special tools. Consult your Unit Injectors - Mechanical Core Acceptance Criteria SELD0030-04 for complete details.
Warranty
Please consult the appropriate Cat parts warranty statement for your area.
Core Management
Please refer to the Caterpillar Core Management Information System (CMIS 2) Parts Information application describing all Cat Reman part/CAF and related information. Also refer to other CMIS 2 inquiry applications such as Customer Profiles, Inspection Reason Codes, Inspection Line Inquiry, Add Charge Information, Entitlement Activity, Entitlement Inquiry, CCR Inquiry, CCR Entry, Shipment Processing; Process Packaging Grief; and Reporting to properly manage core returns and monitor inspection performance. This information will be available to all dealers worldwide after your CMIS 2 conversion date. In the meantime, please continue to use the current CMIS Entitlement Parts Inquiry Screen describing the list of parts in a Core Acceptability Family (CAF) and related part number detail.
For the latest updates of Reman Policies and Core Management (SELD0122), Core Management Systems & Operations Procedures (SELD0040), and Shipping Instructions (SELD0039), go to the Reman Dealer website: catreman.cat.com.
If you have any questions regarding core return processing, feel free to call Corinth toll free at (800) 537-2928. For assistance with technical questions, call the Peoria Reman Technical Help Line also toll free at (888) 88-REMAN or use our E-mail address--Reman_Help.
PELJ0987 CATERPILLAR? ?2009 Caterpillar