106673-7010 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1066737010


 

Information injection-pump assembly

ZEXEL 106673-7010 1066737010
106673-7010 INJECTION-PUMP ASSEMBLY
Rating:
69
Buy INJECTION-PUMP ASSEMBLY 106673-7010 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
106673-7010 
 
   
INJECTION-PUMP ASSEMBLY




Information:


Typical Example2. Remove eight bolts (3) that fasten pipe (1) to the elbow. Remove four bolts (2) that fasten the elbow to the aftercooler cover. Remove elbow (4).
Typical Example3. Remove bracket (5) from the oil filter tube and the oil level gauge group.
Typical Example4. Remove four bolts (7) from the air inlet elbow. Remove plate (6) and elbow (8). 5. Remove two tubes (10) from the air compressor to the aftercooler.6. Remove elbows (9) from the aftercooler housing.
Typical Example
Put identification on bolts (12) because they are 6.4 mm (.25 in) longer than all other bolts. They must be installed in the same location.
7. Remove bolts (11) and (12) from cover, and remove the cover.
Put identification on bolt (14) because it is 12.7 mm (.50 in) shorter than all the other bolts. It must be installed in the same location. Remove four adapters (15). Put plugs in both holes in the aftercooler core assembly. This will keep coolant out of the engine intake manifold.
8. Remove bolts (13) and (14) that hold the core assembly in position.9. Remove the aftercooler core assembly. 10. Remove air line (17) from the fuel ratio control valve.11. Remove eight bolts (16). Remove housing assembly (18).Install Aftercooler
1. Check all seals and gaskets for damage. If damaged, use new parts for replacement.
All foreign material and dirt must be removed from the gasket surface and inside the housing and intake manifold.
2. Install housing (1) and air line (2) to the fuel control valve. 3. Install four new seals (3) on the core assembly. Put clean glycerin on the O-ring seals. 4. Install core assembly (4) inside the housing. Remove plugs in both holes of the aftercooler core assembly. Install the bolts that fasten the core to housing. Install the bolts in their original location. 5. Put clean engine oil in the bores of the adapters. Install adapters (5). 6. Put cover (6) in position on the aftercooler. Install the two bolts in position (7). These bolts are 6.4 mm (.25 in) longer than all other bolts around the housing. Install the remainder of the bolts around the housing. 7. Install elbows (8). 8. Install two tubes (9) between the air compressor and the aftercooler.
Typical Example9. Install elbow (10) and plate (11) on the aftercooler cover. Install the bracket that is a support for the oil filter tube and the oil level gauge group. Install the oil filter tube and the oil level gauge group.
Typical Example10. Install eight bolts (13) that fasten the pipe to elbow (14). Install the elbow in the turbocharger.11. Install the four bolts that fasten the elbow to aftercooler cover (12).12. Fill the engine with coolant to the correct level. See the Operation & Maintenance Manual.

Have questions with 106673-7010?





Group cross 106673-7010 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 619 433 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 613 340 
ME151159 
INJECTION-PUMP ASSEMBLY
6D24T2
106673-7010  
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 319 
ME151050 
INJECTION-PUMP ASSEMBLY
6D22T2
9 400 617 320 
ME157979 
INJECTION-PUMP ASSEMBLY
6D22T
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 610 919 
ME158006 
INJECTION-PUMP ASSEMBLY
6D22TC
F 01G 09U 08W 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 610 920 
ME158001 
INJECTION-PUMP ASSEMBLY
6D22T
9 400 617 321 
ME151286 
INJECTION-PUMP ASSEMBLY
6D22T6
9 400 617 322 
ME158011 
INJECTION-PUMP ASSEMBLY
6D22T
9 400 610 921 
ME158012 
INJECTION-PUMP ASSEMBLY
6D22T
9 400 617 323 
ME158013 
INJECTION-PUMP ASSEMBLY
6D22TC
9 400 617 324 
ME158014 
INJECTION-PUMP ASSEMBLY
6D22TC
Back to top