106673-2730 ZEXEL 9 400 617 261 BOSCH INJECTION-PUMP ASSEMBLY 9400617261 1066732730 me157841

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 617 261 9400617261

ZEXEL 106673-2730 1066732730

MITSUBISHI ME157841 me157841

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106673-2730 zexel genuine, new aftermarket engine parts with delivery

Service parts 106673-2730 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106060-5140

3. GOVERNOR 105408-0690

4. SUPPLY PUMP 105207-1210

5. AUTOM. ADVANCE MECHANIS 105636-1700

6. COUPLING PLATE 105662-0710

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-6211

11. Nozzle and Holder ME059621

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105030-5010

14. NOZZLE

105015-5330

15. NOZZLE SET

Include in #1:

106673-2730 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 617 261 9400617261

ZEXEL 106673-2730 1066732730

MITSUBISHI ME157841 me157841

Zexel num

Bosch num

Firm num

Name

106673-2730

9 400 617 261

ME157841 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D22T * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131424-4620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 12

Pump speed r/min 1050 1050 1050

Average injection quantity mm3/st. 137.2 134.2 140.2

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point -

Rack position 5.8+-0.5

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 15 12.4 17.6

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point C

Rack position 13.9+-0. 5

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 133 113 153

Fixing the lever *

Rack limit *

Injection quantity adjustment_04

Adjusting point D

Rack position R1(6)

Pump speed r/min 275 275 275

Average injection quantity mm3/st. 15 12.4 17.6

Fixing the rack *

Remarks
(check)

Timer adjustment

Pump speed r/min 1200

Advance angle deg. 0.5

Timer adjustment_02

Pump speed r/min -

Advance angle deg. 2 2 2

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Torque spring does not operate. (4)RACK LIMIT (5)Main spring setting (6)Set idle sub-spring (7)Set at delivery (8)Rack difference between N = N1 and N = N2
----------
K=5 N1=1050r/min N2=450r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting (2)At delivery (3)Set the pump speed at aa (4)Set the pump speed at bb.
----------
aa=905r/min bb=1105r/min
----------
a=(30deg)+-5deg b=(2deg) c=(6deg)+-5deg d=(7deg)+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=43.5deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)

Information:

(1) 7S7144 Spring for valves (new): Length under test force ... 44.86 mm (1.766 in)Test force ... 257 25 N (57.7 4.5 lb)Length of spring at valve open position ... 32.28 mm (1.271 in)Load at minimum operating length ... 708 35 N (160 8 lb)Free length after test ... 52.07 mm (2.05 in)Outside diameter ... 35.21 mm (1.386 in)Spring must not be bent more than ... 1.82 mm (.072 in)(2) Height to top of valve guide ... 22.23 0.25 mm (.875 .010 in)(3) Diameter of valve stem (new) ... 9.441 0.008 mm (.3717 .0003 in) Use again minimum diameter ... 9.408 mm (.3704 in)Bore in valve guide with guide installed in the head.Minimum permissible (new) ... 9.456 mm (.3723 in)Maximum permissible (worn) ... 9.581 mm (.3772 in)(4) Valve lip thickness: 6N9916 Exhaust Valve Use again minimum ... 2.69 mm (.106 in)2W2620 Intake Valve Use again minimum ... 2.69 mm (.106 in)6N9915 Intake Valve Use again minimum ... 2.44 mm (.096 in)(5) Diameter of valve head: Exhaust valve ... 48.16 0.13 mm (1.896 .005 in)Intake valve ... 51.31 0.13 mm (2.020 .005 in)(6) Angle of valve face ... 29 1/4 1/4° (7) Depth of bore in head for valve seat insert ... 12.28 0.13 mm (.483 .005 in)(8) Diameter of valve seat insert for exhaust valve ... 50.889 0.013 mm (2.0035 .0005 in) Bore in head for valve seat insert for exhaust valve ... 50.813 0.030 mm (2.0005 .0012 in)Diameter of valve seat insert for intake valve ... 52.032 0.013 mm (2.0485 .0005 in)Bore in head for valve seat insert for intake valve ... 51.956 0.030 mm (2.0455 .0012 in)(9) Angle of face of valve seat insert ... 30 1°(10) Maximum permissible width of valve seat (intake and exhaust) ... 1.93 mm (.076 in) Minimum permissible width of valve seat (intake and exhaust) ... 1.14 mm (.045 in)(11) Dimension from top of closed valve to face of head: Minimum permissible dimension for 6N9916 Exhaust Valve ... 0.66 mm (.026 in)Minimum permissible dimension for 6N9915 or 2W2620 Intake Valve ... 0.15 mm (.006 in)(12) Outside diameter of the face of the valve seat insert: Exhaust seat ... 46.02 mm (1.812 in)Maximum permissible, exhaust seat ... 47.29 mm (1.862 in)Intake seat ... 49.28 mm (1.940 in)Maximum permissible, intake seat ... 50.55 mm (1.990 in)(13) Angle to grind seat face of the insert to get a reduction of maximum seat diameter ... 15°