106672-3660 ZEXEL 9 400 610 903 BOSCH INJECTION-PUMP ASSEMBLY 9400610903 1066723660 220204240a


 

Information injection-pump assembly

BOSCH 9 400 610 903 9400610903
ZEXEL 106672-3660 1066723660
HINO 220204240A 220204240a
106672-3660 INJECTION-PUMP ASSEMBLY
Rating:
84
Buy INJECTION-PUMP ASSEMBLY 106672-3660 zexel genuine, new aftermarket engine parts with delivery

Service parts 106672-3660 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106060-7421
3. GOVERNOR 105407-3600
4. SUPPLY PUMP 105217-1301
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105662-0850
7. COUPLING PLATE 156637-3720
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-5572
11. Nozzle and Holder 23600-1860D
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105031-5461
14. NOZZLE 105015-7020
15. NOZZLE SET

Include in #1:

106672-3660 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 903 9400610903
ZEXEL 106672-3660 1066723660
HINO 220204240A 220204240a


Zexel num
Bosch num
Firm num
Name
106672-3660 
9 400 610 903 
220204240A  HINO
INJECTION-PUMP ASSEMBLY
EK130T K
106672-3660 
9 400 610 903 
S220204240A  HINO
INJECTION-PUMP ASSEMBLY
EK130T A K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-0920
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.3 3.2 3.3
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   8.8
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   152.5 150.5 154.5
Max. variation between cylinders %   0 -4 4
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   5.1+-0.5
Pump speed r/min   360 360 360
Average injection quantity mm3/st.   11 8 14
Max. variation between cylinders %   0 -15 15
Fixing the rack   *

Test data Ex:

Governor adjustment

Test data 106672-3660
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Set idle sub-spring
----------
K=17
----------

Speed control lever angle

Test data 106672-3660
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=22deg+-5deg

Stop lever angle

Test data 106672-3660
N:Pump normal S:Stop the pump. (1)Rack position aa or less, pump speed bb
----------
aa=4.6mm bb=0r/min
----------
a=27deg+-5deg b=53deg+-5deg

Timing setting

Test data 106672-3660
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(0deg)




Information:

Cautions Regarding Battery* Handle Battery Carefully * Never use flames or allow sparks near the battery. The battery releases flammable hydrogen gas and oxygen gas. These gases can be ignited by flames and cause an explosion.* Do not use the battery when the fluid surface is lower than the minimum level. Using a battery with a low electrolyte level can result in an explosion.* Do not short the battery terminals with a tool or other metal object.* When disconnecting battery cables, always remove the cable from the negative (-) terminal first. When reconnecting cables, attach the cable to the positive (+) terminal first.* Charge the battery in a well-ventilated area, with all filling hole plugs removed.* Make sure the cable clamps are securely installed on the battery terminals. A loose cable clamp can cause sparks that may result in explosion.* Before servicing electrical components or conducting electrical welding, set the battery switch to the [Open/OFF] position or disconnect the cable from the negative (-) battery terminal to cut off the electrical current.* Electrolyte (battery fluid) contains dilute sulfuric acid. Careless handling of the battery can lead to the loss of sight and/or burns. Also, do not swallow electrolyte.* Wear protective goggles and rubber gloves when maintaining and inspecting the battery (when adding water, charging, etc.).* If electrolyte is spilled onto the skin or clothes, immediately wash with lots of clean fresh water and thoroughly clean with soap.* If electrolyte gets into eyes, immediately flush with lots of clean fresh water and seek immediate medical attention.* Should you accidentally swallow electrolyte, gargle with plenty of water, then drink lots of water, and seek immediate medical attention.
Response To Abnormalities* If Engine Overheats, Conduct Heating Operation Before Stopping The Engine If the engine overheats, do not stop the engine immediately. Abruptly stopping an overheated engine may cause the coolant temperature to rise, resulting in seizing of the engine. If the engine overheats, operate the engine at low idling speed (cooling temperature), and stop the engine after the coolant temperature lowers sufficiently.Do not add coolant immediately after stopping the engine. Adding coolant to a hot engine may cause damage to the cylinder heads due to sudden change in temperature. Add coolant after the engine cools to room temperature.* If Engine Stops Due To Abnormality, Exercise Caution When Restarting If the engine stops due to an abnormality, do not restart the engine immediately. If the engine stops with an alarm, check and correct the cause of the problem before restarting. Operating the engine without correcting the problem may result in serious engine problems.* If Oil Pressure Drops, Stop Engine Immediately If the engine oil pressure decreases, stop the engine immediately, and inspect the lubrication system. Operating the engine with low oil pressure may cause seizing of the bearings and other parts.* If Fan Belt Breaks, Stop Engine Immediately If the fan belt breaks, stop the engine immediately. Continued operation of the engine without the fan belt causes coolant to change to steam and

Have questions with 106672-3660?





Group cross 106672-3660 ZEXEL

Hino 

 
220007100A 
INJECTION-PUMP ASSEMBLY
K13D
 
220007100B 
INJECTION-PUMP ASSEMBLY
K13D
9 400 619 806 
220007100C 
INJECTION-PUMP ASSEMBLY
K13D
F 01G 09U 08D 
220007102A 
INJECTION-PUMP ASSEMBLY
K13D
F 019 Z10 636 
 
INJECTION-PUMP ASSEMBLY

Hino 

F 01G 09U 08E 
220007103A 
INJECTION-PUMP ASSEMBLY
K13D
9 400 617 102 
220007104A 
INJECTION-PUMP ASSEMBLY
K13D
 
220007110A 
INJECTION-PUMP ASSEMBLY
K13D
F 019 Z10 637 
220007110B 
INJECTION-PUMP ASSEMBLY
K13D
 
220007110C 
INJECTION-PUMP ASSEMBLY
K13D
 
220007112A 
INJECTION-PUMP ASSEMBLY
K13D
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220007113A 
INJECTION-PUMP ASSEMBLY
K13D
9 400 617 103 
220007114A 
INJECTION-PUMP ASSEMBLY
K13D
9 400 617 104 
220203720A 
INJECTION-PUMP ASSEMBLY
EP100-T
9 400 619 864 
220204010A 
INJECTION-PUMP ASSEMBLY
EP100-T
9 400 617 105 
220204011A 
INJECTION-PUMP ASSEMBLY
EP100-T
9 400 617 105 
S220204011A 
INJECTION-PUMP ASSEMBLY
EP100-T
9 400 617 106 
220204170A 
INJECTION-PUMP ASSEMBLY
M10C-T
 
220204160A 
INJECTION-PUMP ASSEMBLY
EK130-T
9 400 617 107 
220204161A 
INJECTION-PUMP ASSEMBLY
EK130-T
9 400 617 107 
S220204161A 
INJECTION-PUMP ASSEMBLY
EK130-T
106672-3660  
9 400 610 903 
220204240A 
INJECTION-PUMP ASSEMBLY
EK130T
106672-3660  
9 400 610 903 
S220204240A 
INJECTION-PUMP ASSEMBLY
EK130T
9 400 610 904 
220204370A 
INJECTION-PUMP ASSEMBLY
EK130-T
 
220204440A 
INJECTION-PUMP ASSEMBLY
EP100-T
 
220204270A 
INJECTION-PUMP ASSEMBLY
EK130-T
 
220204271A 
INJECTION-PUMP ASSEMBLY
EK130-T
9 400 617 108 
220204272A 
INJECTION-PUMP ASSEMBLY
EK130-T
Back to top