106671-8641 ZEXEL F 019 Z10 412 BOSCH INJECTION-PUMP ASSEMBLY f019z10412 1066718641

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH F 019 Z10 412 f019z10412

ZEXEL 106671-8641 1066718641

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-8641 zexel genuine, new aftermarket engine parts with delivery

Service parts 106671-8641 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106061-7720

3. GOVERNOR 105407-5180

4. SUPPLY PUMP 105217-1930

5. AUTOM. ADVANCE MECHANIS 105635-0350

6. COUPLING PLATE 105663-0540

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-5721

11. Nozzle and Holder 23600-1970B

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105031-5470

14. NOZZLE

105015-7020

15. NOZZLE SET

Include in #1:

106671-8641 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 412 f019z10412

ZEXEL 106671-8641 1066718641

Zexel num

Bosch num

Firm num

Name

106671-8641
106671-8642

F 019 Z10 412

INJECTION-PUMP ASSEMBLY
* K 14CA PE6P,6PD PE

106671-8641
106671-8642

F 019 Z10 412

S220204081A HINO

INJECTION-PUMP ASSEMBLY
A * K 14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-0920

Overflow valve opening pressure kPa 160.5 144 177

Overflow valve opening pressure kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-4-2-6- 3-5

Pre-stroke mm 4.4 4.34 4.4

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point A

Rack position 9.3

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 194 192 196

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the rack *

Injection quantity adjustment_02

Adjusting point D

Rack position 5.6+-0.5

Pump speed r/min 360 360 360

Average injection quantity mm3/st. 11 8 14

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_03

Adjusting point E

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 200 190 210

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 900++

Advance angle deg. 0 0 0

Remarks
Do not advance until starting N = 900.

Timer adjustment_02

Pump speed r/min 900

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min -

Advance angle deg. 1 1 1

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Main spring setting (5)Set idle sub-spring
----------
K=5
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting (2)Set the pump speed at aa (3)Set the pump speed at bb. (4)Stopper bolt setting
----------
aa=900r/min bb=750r/min
----------
a=3deg+-5deg b=20deg+-5deg c=5deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Contacts inner boss. (2)Rack position aa or less, pump speed bb (3)Contacts outer boss. (4)Normal
----------
aa=5.1mm bb=0r/min
----------
a=27deg+-5deg b=53deg+-5deg c=(11deg)

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(0deg)

Information:

Repeat Steps 4 through 6 to remove (bleed) air from the rear table lift cylinder (not shown).
Open (CCW) hand pump control knob (11) to completely lower the DPF cleaner table. Close (CW) the hand pump control knob.
Illustration 38 g02728258
(28) Hydraulic Oil Level 51 to 102 mm (2.0 to 4.0 inch)
Check the oil level in the pump reservoir. Remove fill cap (13) located on the end cap of the hand pump. Hydraulic oil level (28) should be 51 to 102 mm (2.0 to 4.0 inch) from the bottom of the fill hole. Add high-grade hydraulic oil, if needed.Note: A clean wire tie can be used as a dipstick to measure the hydraulic oil level in the pump reservoir.Troubleshooting Guide
Table 3
Symptom Solution
Air dryer desiccant is a pinkish color. 1. Replace or regenerate the desiccant. Refer to ""Maintenance Section"".
Bursting does not occur. 1. Check display screen for error message.
2. Check power connection to burst valve solenoid.
Cabinet doors do not close correctly. 1. Look for damaged door hinges, seals, and latches.
2. Verify that vehicle sensors have been removed from DPF.
Cabinet doors open during burst process. 1. Verify that doors are correctly latched.
2. Look for damage to door latches.
3. Check seals between DPF and adapters.
Clamping force cannot be obtained. 1. Look for hydraulic fluid leaks.
2. Check fluid level in hydraulic pump. Refer to ""Maintenance Section"".
Clamping force does not hold. 1. Upon initial clamping, it is possible for clamp load to drop
689 to 1379 kPa (99.9 to 200.0 psi) within the first minute, due to temperature effects. After reclamping, the drop should be virtually zero.
2. Look for hydraulic fluid leaks.
Display screen is blank. 1. Verify that machine is ON, plugged into an outlet, and power is available to the outlet.
2. Reset circuit breakers located on left side of control cabinet.
DPF does not line up correctly on the table. 1. Verify that correct adapters are being used.
2. Verify DPF is correctly seated on to lower adapter.
DPF is damaged after cleaning process. 1. Check DPFs for damage before cleaning.
2. Look for damage on adapters.
3. Verify that correct cleaning protocol was entered into machine.
DPF is not cleaned. 1. Check orientation of DPF. Refer to ""General Information"" Section.
2. Verify that correct cleaning protocol was entered into machine.
3. Look for other DPF conditions that may prevent successful cleaning.