106671-8562 ZEXEL F 019 Z10 864 BOSCH INJECTION-PUMP ASSEMBLY f019z10864 1066718562 220204001a


 

Information injection-pump assembly

BOSCH F 019 Z10 864 f019z10864
ZEXEL 106671-8562 1066718562
HINO 220204001A 220204001a
106671-8562 INJECTION-PUMP ASSEMBLY
Rating:
63
Buy INJECTION-PUMP ASSEMBLY 106671-8562 zexel genuine, new aftermarket engine parts with delivery

Service parts 106671-8562 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106061-5672
3. GOVERNOR 105407-4350
4. SUPPLY PUMP 105207-1790
5. AUTOM. ADVANCE MECHANIS 105635-0320
6. COUPLING PLATE 105662-0850
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-5572
11. Nozzle and Holder 236001860D
12. Open Pre:MPa(Kqf/cm2) 21.6(220)
13. NOZZLE-HOLDER 105031-5461
14. NOZZLE 105015-7020
15. NOZZLE SET

Include in #1:

106671-8562 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 864 f019z10864
ZEXEL 106671-8562 1066718562
HINO 220204001A 220204001a


Zexel num
Bosch num
Firm num
Name
106671-8562 
106671-8563 
F 019 Z10 864 
220204001A  HINO
INJECTION-PUMP ASSEMBLY
EK130-T * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-0920
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.3 3.2 3.3
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   11.1
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   128 126 130
Max. variation between cylinders %   0 -4 4
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   6+-0.5
Pump speed r/min   400 400 400
Average injection quantity mm3/st.   13.5 10.5 16.5
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Timer adjustment
Pump speed r/min   900++
Advance angle deg.   0 0 0
Remarks
Do not advance until starting N = 900.
 
Timer adjustment_02
Pump speed r/min   -
Advance angle deg.   4.5 4.5 4.5
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 106671-8562
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Set idle sub-spring
----------
K=8
----------

Speed control lever angle

Test data 106671-8562
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=0deg+-5deg b=18deg+-5deg

Stop lever angle

Test data 106671-8562
N:Pump normal S:Stop the pump. (1)Normal stop (2)Rack position aa or less, pump speed bb
----------
aa=5.5mm bb=0r/min
----------
a=38deg+-5deg b=53deg+-5deg

Timing setting

Test data 106671-8562
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(0deg)




Information:


Table 4
Storage Temperature Expected DEF Life
Below 25° C (77° F) 18 months
25° C (77° F) to 30° C (86° F) 12 months
30° C (86° F) to 35° C (95° F) 6 months
Above 35° C (95° F) test quality before use Refer to "ISO 22241" document series for more information about DEF quality control.Note: Dispose of all fluids according to applicable regulations and mandates.DEF/Urea Solution Recommendations for Marine Engines
The US has adopted/approved NOx Emissions Control Area (ECA) regulations. Per ECAs, vessels that are 2016 and later models, or vessels that are modified to 2016 models, are required to meet Tier III NOx standards. These engines may require the use of Diesel Exhaust Fluid (DEF) and other urea solutions for engines equipped with Selective Catalytic Reduction (SCR) systems. If required, Cat marine engines are designed to operate on DEF of urea concentrations of 32.5 percent (by weight) or 40 percent (by weight). The crystallization temperature of 40 percent urea solution is 0° C (32° F). If urea solution ambient temperatures are routinely below 5° C (41° F) and supplemental heat is not applied to urea storage, then 32.5 percent solution should be used and maintained at a temperature above −0° C (14° F). Urea solutions should be maintained above the specified freezing temperature. Consult the urea supplier and follow the guidelines provided in this article for handling and recommendations.Vessels that are traveling internationally and have on/off NOx controls that allow the vessels to meet ECA regulations must enable NOx controls prior to entering the ECA. For US flagged vessels, the SCR must be activated and deactivated automatically based on input from the Global Positioning System. For US flagged vessels, on/off NOx controls are allowed on engines > 30 liters/cylinder and are not allowed on engines < 30 liters/cylinder unless installed on a vessel with propulsion engines >30 liters/cylinder. Otherwise the NOx control systems on Category 1 and 2 engines must always be on. Foreign destinations should be reviewed for supply of ULSD fuel and DEF prior to departure. Exemptions for ULSD or DEF use due to fluid unavailability per 40 CFR part 1042.650(a) by US flagged vessels operating outside of US waters may be requested from the US Environmental Protection Agency (EPA). The EPA can be contacted at the following address:complianceinfo@epa.gov
When used in marine engines, DEF of 32.5 percent urea concentration must meet all the guidelines and quality recommendations given in this Chapter.When used in marine engines, urea solution of 40 percent urea concentration must follow all the DEF guidelines and quality recommendations given in this chapter and must meet the characteristics listed in Table 5 for 40 percent concentration. The supplier should provide documentation to prove that the urea solution is compliant with the characteristics published in Table 5.Refer to your engine Operation and Maintenance Manual to determine the concentration of urea solution allowed in your engine.
Cat does not warrant the quality or performance of non-Cat fluids and greases.
General Characteristics of DEF
For detailed information on the requirements and

Have questions with 106671-8562?





Group cross 106671-8562 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220204000A 
INJECTION-PUMP ASSEMBLY
F 019 Z10 863 
220204000A 
INJECTION-PUMP ASSEMBLY
EK130-T
106671-8562  

106671-8563 
F 019 Z10 864 
220204001A 
INJECTION-PUMP ASSEMBLY
EK130-T
9 400 611 532 
220204002A 
INJECTION-PUMP ASSEMBLY
EK130-T
Back to top