106671-5790 ZEXEL 9 400 612 663 BOSCH INJECTION-PUMP ASSEMBLY 9400612663 1066715790 1671396979


 

Information injection-pump assembly

BOSCH 9 400 612 663 9400612663
ZEXEL 106671-5790 1066715790
NISSAN-DIESEL 1671396979 1671396979
106671-5790 INJECTION-PUMP ASSEMBLY
Rating:
77
Buy INJECTION-PUMP ASSEMBLY 106671-5790 zexel genuine, new aftermarket engine parts with delivery

Service parts 106671-5790 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106061-7241
3. GOVERNOR 105489-5670
4. SUPPLY PUMP 105237-4210
5. AUTOM. ADVANCE MECHANIS 105681-2180
6. COUPLING PLATE 105663-0640
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105160-4470
11. Nozzle and Holder 16600-96610
12. Open Pre:MPa(Kqf/cm2) 22.6{230}
13. NOZZLE-HOLDER 105030-4540
14. NOZZLE 105025-0850
15. NOZZLE SET

Include in #1:

106671-5790 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 612 663 9400612663
ZEXEL 106671-5790 1066715790
NISSAN-DIESEL 1671396979 1671396979


Zexel num
Bosch num
Firm num
Name
106671-5790 
9 400 612 663 
1671396979  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
PF6TA K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   132424-0620
Overflow valve opening pressure kPa   157 157 157
Overflow valve opening pressure kgf/cm2   1.6 1.6 1.6
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.9 3.85 3.95
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.8
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   165 163 167
Max. variation between cylinders %   0 -4 4
Basic   *
Fixing the lever   *
Boost pressure kPa   77.3 77.3
Boost pressure mmHg   580 580
Injection quantity adjustment_02
Adjusting point   D
Rack position   7.7
Pump speed r/min   400 400 400
Average injection quantity mm3/st.   55 49 61
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Injection quantity adjustment_03
Adjusting point   E
Rack position   6+-0.5
Pump speed r/min   260 260 260
Average injection quantity mm3/st.   14.5 13.2 15.8
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Boost compensator adjustment
Pump speed r/min   400 400 400
Rack position   7.7
Boost pressure kPa   12 10.7 13.3
Boost pressure mmHg   90 80 100
Boost compensator adjustment_02
Pump speed r/min   400 400 400
Rack position   11.2+0.2
Boost pressure kPa   64 64 64
Boost pressure mmHg   480 480 480
Timer adjustment
Pump speed r/min   750--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   700
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1020
Advance angle deg.   1 0.5 1.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106671-5790
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Rack limit using the stop lever: R1 (5)Boost compensator stroke: BCL (6)Damper spring setting (7)Variable speed specification: idling adjustment (8)Fix the lever at the full-load position at delivery. (9)Main spring setting (10)Perform governor adjustment at an ambient temperature of at least 15 deg C (boost compensator start spring is shape memory alloy).
----------
RT=1 TH=2.1mm R1=11.2+0.2mm BCL=(3.6)mm
----------

Speed control lever angle

Test data 106671-5790
F:Full speed I:Idle (1)Pump speed = aa (2)Set the stopper bolt (fixed at full-load position at delivery.)
----------
aa=290r/min
----------
a=14deg+-5deg b=4deg+-5deg

0000000901

Test data 106671-5790
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=18.5deg+-5deg b=30deg+-3deg

Stop lever angle

Test data 106671-5790
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Use the pin at R = bb
----------
aa=11.2+0.2mm bb=40mm
----------
a=37.5deg+-5deg b=35.5deg+-5deg

Timing setting

Test data 106671-5790
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(20deg)




Information:

Fuel consumption complaints are related to engine owners expectations. They may often times be related to the engine itself, causes other than the engine, and in some cases the fuel consumption may be normal for the application. Only a good discussion with the owner/operator, as described in the "Owner/Operator Input" section, will give guidance as to a correct repair or to prevent unnecessary repairs.Owner/Operator Input
The following are some of the questions which should be asked before beginning any diagnosis or repair for an engine performance complaint. There Are No Hard And Fast Answers For These Questions. There are many factors that can cause poor fuel mileage or make users believe they are getting fuel-poor-mileage.There are also a variety of customer expectations which are acceptable. The answers to these questions will give you a better understanding and perspective on the complaint and may identify characteristics which will help pinpoint the cause of the complaint quickly.1. Are miles measured accurately? A most common problem in determining mpg is errors in recording the number of miles traveled.A. Is this vehicle hub or cab odometer accurate? The easiest way to check an odometer is to install a hub odometer known to be accurate and for the tire size on the truck. Run the truck over several hundred miles and compare the reading with the original odometer.Odometers may also be checked by comparing them to interstate mile posts or by running over a course of known length - a 50-mile run is required to get a good check.B. Are "book miles" or "driver-paid miles" correct? Another way in which miles for mpg calculations are obtained by a fleet is the use of "book miles" or "driver-paid miles". The use of this system can short mileage accumulation by 10 to 15%; thus, mpg is low by 10 to 15%.C. Is the vehicle used for pick-up and delivery operation? Another problem affecting mileage accumulation in many fleets is the use of linehaul equipment for pickup and delivery operations. In the "book mile" system, the truck rarely gets credit for any miles run in pick-up and delivery.2. Is fuel measurement accurate? There are a number of ways in which fuel measurement can be the source of mpg problems.A. Are fuel pumps calibrated? If fuel tickets come from company-owned fuel pumps, there can be errors because nonrevenue fuel pumps do not have calibration requirements in many states.B. Are road fuel tickets accurate? The only way to verify fuel additions when road fuel tickets are used is a laborious ticket-by-ticket audit ensuring that the correct amount of fuel has been entered for the vehicles in question and that there are no indications of incorrect entries.C. Are tank-full mileage checks correctly done? The big problem in "tank-full" checks is getting the tank filled to the same level before and after the user "checked the mileage". With two 100 gallon tanks, errors of 5 to 10 gallons are very common in topping off tanks because of the way truck tanks

Have questions with 106671-5790?





Group cross 106671-5790 ZEXEL

Nissan-Diesel 

9 400 616 872 
1671496502 
INJECTION-PUMP ASSEMBLY
PE6TE
9 400 619 956 
1671496503 
INJECTION-PUMP ASSEMBLY
PE6T
9 400 616 873 
1671496500 
INJECTION-PUMP ASSEMBLY
PE6TA
9 400 616 874 
1671496501 
INJECTION-PUMP ASSEMBLY
PE6TA
9 400 616 875 
1671396978 
INJECTION-PUMP ASSEMBLY
PE6T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 876 
1680196671 
INJECTION-PUMP ASSEMBLY
PF6TA
F 01G 09U 07F 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 07G 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 877 
1680195511 
INJECTION-PUMP ASSEMBLY
NF6TA
9 400 616 878 
1671396976 
INJECTION-PUMP ASSEMBLY
PF6TA
9 400 616 879 
1679096609 
INJECTION-PUMP ASSEMBLY
PF6T24
106671-5790  
9 400 612 663 
1671396979 
INJECTION-PUMP ASSEMBLY
PF6TA
Back to top