106671-4231 ZEXEL 9 400 616 796 BOSCH INJECTION-PUMP ASSEMBLY 9400616796 1066714231 6151711680


 

Information injection-pump assembly

BOSCH 9 400 616 796 9400616796
ZEXEL 106671-4231 1066714231
KOMATSU 6151711680 6151711680
106671-4231 INJECTION-PUMP ASSEMBLY
Rating:
14
Buy INJECTION-PUMP ASSEMBLY 106671-4231 zexel genuine, new aftermarket engine parts with delivery

Service parts 106671-4231 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106060-5891
3. GOVERNOR 105487-2490
4. SUPPLY PUMP 105217-1600
5. AUTOM. ADVANCE MECHANIS 105635-0210
6. COUPLING PLATE 105663-0400
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105111-4160
11. Nozzle and Holder 6152-11-3200
12. Open Pre:MPa(Kqf/cm2) 24.5{250}
13. NOZZLE-HOLDER 105041-7080
14. NOZZLE 105015-6770
15. NOZZLE SET

Include in #1:

106671-4231 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
106671-4231 
9 400 616 796 
6151711680  KOMATSU
INJECTION-PUMP ASSEMBLY
S6D125 * K 14CA INJECTION PUMP ASSY PE6P,6PD PE




Information:

Your vehicle/engine may not have the same or all of the gauges. Check your Vehicle/Truck Owners Manual for information on the layout of your gauge package. Gauges provide a "look" inside the engine. Be sure they are in good working order. Determine what is the "normal" operating range by observing your gauges over a period of time.Noticeable changes in gauge readings are an indicator of potential gauge or engine problems. This also applies to gauge readings that have changed significantly but are still within specifications. The cause of any sudden or significant change in the readings should be determined and corrected. Contact Caterpillar for assistance as needed.
If no oil pressure is indicated, stop the engine. Engine damage can result.
Oil Pressure - Typical oil pressure range is between 240 and 480 kPa (35 and 70 psi) (running at rated engine speed, with SAE 10W-30 oil, at operating temperature.) A lower pressure is normal at low idle. Water (Coolant) Temperature - Typical water temperature range is 87° to 98°C (189° to 208°F). Maximum allowable temperature is 105°C (220°F) with the cooling system pressurized radiator cap. Higher temperatures may occur under certain conditions. Ammeter -Indicates the amount of charge or discharge in the battery charging circuit. Typical operation of the indicator should be slightly to the positive (right) side of "0" (zero). With the engine running, during normal operation, if the indicator is constantly to the negative (left) side of "0" (zero) or shows excessive charge, have the charging system checked for malfunction.
Do not exceed 2900 rpm in any situation. Overspeeding when downshifting, going downhill, etc., can result in serious damage to your engine.
Tachometer -Indicates engine speed (rpm). The engine can be operated at high idle rated speed without damage, but should not be allowed to overspeed. Refer to the Engine Information Plate on the engine for information regarding high idle and full load speeds. Fuel Level -Indicates fuel level in the fuel tank. Electrically operated, it registers only when the key switch is ON. Service Hour Meter (If Equipped)-Indicates the total number of clock hours the engine has operated.

Have questions with 106671-4231?





Group cross 106671-4231 ZEXEL

Komatsu 

 
6152711281 
INJECTION-PUMP ASSEMBLY
SA6D125
 
6152711612 
INJECTION-PUMP ASSEMBLY
SA6D125
 
 
INJECTION-PUMP ASSEMBLY
SA6D125
 
6152711521 
INJECTION-PUMP ASSEMBLY
SA6D125
106671-4231  
9 400 616 796 
6151711680 
INJECTION-PUMP ASSEMBLY
S6D125
 
 
INJECTION-PUMP ASSEMBLY

Yanmar 

9 400 611 618 
12862751010 
INJECTION-PUMP ASSEMBLY
6GH-UT

Komatsu 

9 400 616 797 
6152711523 
INJECTION-PUMP ASSEMBLY
SA6D125

Daewoo 

 
 
INJECTION-PUMP ASSEMBLY
D1146T
 
 
INJECTION-PUMP ASSEMBLY
D1146T
 
 
INJECTION-PUMP ASSEMBLY
D2366
 
 
INJECTION-PUMP ASSEMBLY
D2366T

Komatsu 

 
6152711310 
INJECTION-PUMP ASSEMBLY
SA6D125
Back to top