106671-2550 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066712550 me056252

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 106671-2550 1066712550

MITSUBISHI ME056252 me056252

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-2550 zexel genuine, new aftermarket engine parts with delivery

Service parts 106671-2550 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106067-5621

3. GOVERNOR 105487-1040

4. SUPPLY PUMP 105207-1041

5. AUTOM. ADVANCE MECHANIS 105636-0440

6. COUPLING PLATE 105662-0710

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-4771

11. Nozzle and Holder 30961-20010

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105031-3522

14. NOZZLE 105015-4380

15. NOZZLE SET

Include in #1:

106671-2550 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106671-2550 1066712550

MITSUBISHI ME056252 me056252

Zexel num

Bosch num

Firm num

Name

106671-2550

ME056252 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D22 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 7.5

Pump speed r/min 700 700 700

Each cylinder's injection qty mm3/st. 93 90.4 95.6

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point E

Rack position 5+-0.5

Pump speed r/min 500 500 500

Each cylinder's injection qty mm3/st. 16.5 14 19

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(7.5)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 93 92 94

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1(7.5)

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 107 103 111

Difference in delivery mm3/st. 8 8 8

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position 5.7+-0.5

Pump speed r/min 200 200 200

Each cylinder's injection qty mm3/st. 16.5 14 19

Fixing the rack *

Remarks
(check)

Injection quantity adjustment_06

Adjusting point F

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 115 95 135

Fixing the lever *

Timer adjustment

Pump speed r/min 1000--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 950

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1050

Advance angle deg. 2 1.5 2.5

Timer adjustment_04

Pump speed r/min 1150

Advance angle deg. 4 3.5 4.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)Excess fuel setting for starting: SXL
----------
DL=4.5-0.2mm SXL=R1+0.2mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=28deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=21.5deg+-5deg b=24deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=25deg+-5deg b=64deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=5.4mm
----------

0000001601 RACK SENSOR

V1:Output voltage Vf:Full side output voltage (A) Load lever (B) Nut (c) Nut (F) Full (P) Potentiometer 1. Load sensor adjustment (1)Apply DC24V to between the potentiometer (P)'s connector terminals (1) ~ (3) and measure the output voltage between (1) ~ (2). (2)Position the load lever (A) against the full side stopper bolt and turn the nut (B) to adjust the potentiometer (P)'s output voltage to Vf. (3)Confirm that the load lever (A) moves smoothly between full and idle and then tighten nut (C). (Tightening torque: 4.4 - 7 N.m {0.5 - 0.7 kgf.m}) (4)Hold the load lever (A) several times against the full side stopper bolt and confirm potentiometer (P)'s output voltage Vf.
----------
Vf=1.6+-0.1V
----------

Information:

Start By:a. remove valve covers 1. Loosen the fuel injection line nut at the nozzle end with tool (A).2. Loosen the fuel line nut at the fuel injection line adapter with tool (B). Remove inner fuel injection lines (1). Install caps and plugs on all fuel line openings to keep dirt out of the fuel system. If necessary, use tooling (D) to turn the engine so the valves do not make contact with the pistons when the valves are opened with tool (C) to remove the push rods.3. Put compression on the valve springs with tool (C), and remove push rods (2). Put identification marks on the push rods as to their location in the engine.4. Push the push rod end of the rocker arms down. 5. Remove the intake valve lifter with tooling (E) as follows:a. Install 5P2685 Nut (3) and 5P6601 Collet (4) on 5P2408 Outer Handle Assembly (5).b. Install 5P6599 Inner Handle Assembly (6) in 5P2408 Outer Handle Assembly (5). c. Install tooling (E) in the intake valve lifter. Hold the 5P2408 Outer Handle Assembly, and tighten the 5P6599 Inner Handle Assembly until the 5P6601 Collet is tight against the inside of the intake valve lifter. d. Remove intake valve lifters (7) from the cylinder block with tooling (E). Put identification marks on the lifters as to their location in the engine. 6. Remove the exhaust valve lifters with tooling (E) as follows:a. Install 5P2685 Nut (3) and 5P6601 Collet (4) on 5P2408 Outer Handle Assembly (5). The opening in the cylinder head assembly for the intake valve lifter is larger than the opening in the exhaust valve lifter side. The tooling and each valve lifter must be installed and removed from the intake valve lifter side.b. Install the outer handle assembly in the intake valve lifter side of the cylinder head assembly. Slide the flat area of 5P2408 Outer Handle Assembly (5) through the head casting, and install the 5P6601 Collet in the exhaust valve lifters. c. Install 5P6599 Inner Handle Assembly (6) in 5P2408 Outer Handle Assembly (5). Hold the 5P2408 Handle Assembly, and tighten the 5P6599 Handle Assembly until the 5P6601 Collet is tight against the inside of the exhaust valve lifter.d. Pull the exhaust valve lifter up until the spring on the exhaust valve lifter is free from the cylinder block.e. Remove the 5P6599 Inner Handle Assembly. Slide the 5P2408 Outer Handle Assembly through the head casting, and remove it from the intake valve lifter side of the cylinder head. f. Use a magnet, and remove exhaust valve lifters (8) from the intake valve lifter side of the cylinder head assembly. Put identification marks on the lifters as to their location in the engine.7. Remove the guide springs from the lifters.Install Valve Lifters
Steps 1 and 2 must be done to install intake or exhaust valve lifters.
Make sure guide spring (9) is not damaged or worn. If the guide spring is damaged or worn, replace the guide spring. See Guideline For Reusable