106671-1814 ZEXEL 9 400 619 689 BOSCH INJECTION-PUMP ASSEMBLY 9400619689 1066711814 1156028184


 

Information injection-pump assembly

BOSCH 9 400 619 689 9400619689
ZEXEL 106671-1814 1066711814
ISUZU 1156028184 1156028184
106671-1814 INJECTION-PUMP ASSEMBLY
Rating:
38
Buy INJECTION-PUMP ASSEMBLY 106671-1814 zexel genuine, new aftermarket engine parts with delivery

Service parts 106671-1814 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106061-7701
3. GOVERNOR 105489-3893
4. SUPPLY PUMP 105237-4440
5. AUTOM. ADVANCE MECHANIS 105691-3632
6. COUPLING PLATE 105662-1301
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-7442
11. Nozzle and Holder 1-15300-351-0
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/23.5{240}
13. NOZZLE-HOLDER 105030-3462
14. NOZZLE 105015-9190
15. NOZZLE SET

Include in #1:

106671-1814 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
106671-1814 
106671-1815 
9 400 619 689 
1156028184  ISUZU
INJECTION-PUMP ASSEMBLY
6WA1-TCN * K




Information:

Start By:a. remove radiator
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Loosen bolt (4), bolt (5), and bolt (6). Remove belts (3).2. Remove bolts (2) and fan (1). 3. Remove bolt (7) and washer (8). Put enough spacers (10) on bolt (7) to get approximately 3.18 mm (.125 in) of clearance between washer (8) and vibration damper and pulley assembly (9). Install bolt (7), washer (8), and spacers (10).
If spacers (10) are not used, damage to the bolt and/or crankshaft can result when the vibration damper and pulley are removed from the crankshaft.
4. Install tool (A) as shown, and loosen vibration damper and pulley assembly (9).5. Remove tool (A), bolt (7), washer (8), spacers (10), and vibration damper and pulley assembly (9). 6. If necessary, remove bolts (11) and vibration damper (12). The following steps are to install the crankshaft vibration damper and pulley. Inspect the vibration damper housing for leakage or dents (damage housing). If either condition exists, a replacement of the vibration damper must be made.7. Install vibration damper (12) on pulley (13). Install bolts (11).8. Install vibration damper and pulley assembly (9) and install bolt (7), spacers (10) and washer (8).
The flat side of washer (8) must be installed toward vibration damper and pulley assembly (9).
9. Tighten bolt (7) to a torque of 284 to 340 N m (210 to 250 lb ft). Hit bolt (7) with a hammer and retighten to a torque of 284 to 340 N m (210 to 250 lb ft).10. Position belts (3). Tighten bolts (4), (5), and (6). Use a belt tension gauge and make an adjustment of the belts. Measure the belt farthest from the engine. Tighten new belts until the gauge indication is 534 22 N (120 5 lb ft). Operate the engine at high idle for a minimum of 30 minutes after installing radiator and guards. Make another adjustment of the belt tension. The correct gauge indication for a used belt is 400 44 N (90 10 lb.). Tighten bolt (4), bolt (5), and bolt (6).11. Install fan (1) and bolt (2).End By:a. install radiator
Perform Scheduled Oil Sampling on oil wetted compartments after performing service work to check for contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.

Have questions with 106671-1814?





Group cross 106671-1814 ZEXEL

Isuzu 

 
1156028180 
INJECTION-PUMP ASSEMBLY
6WA1-TCN
 
1156028181 
INJECTION-PUMP ASSEMBLY
6WA1-TCN
 
1156028182 
INJECTION-PUMP ASSEMBLY
6WA1-TCN
 
1156028183 
INJECTION-PUMP ASSEMBLY
6WA1-TCN
106671-1814  

106671-1815 
9 400 619 689 
1156028184 
INJECTION-PUMP ASSEMBLY
6WA1-TCN
9 400 611 716 
1156028185 
INJECTION-PUMP ASSEMBLY
6WA1-TCN
9 400 616 729 
1156028186 
INJECTION-PUMP ASSEMBLY
6WA1-TCN
Back to top