106671-1430 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066711430 1156018460


 

Information injection-pump assembly

ZEXEL 106671-1430 1066711430
ISUZU 1156018460 1156018460
106671-1430 INJECTION-PUMP ASSEMBLY
Rating:
34
Buy INJECTION-PUMP ASSEMBLY 106671-1430 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

ZEXEL 106671-1430 1066711430
ISUZU 1156018460 1156018460


Zexel num
Bosch num
Firm num
Name
106671-1430 
106671-1431 
 
1156018460  ISUZU
INJECTION-PUMP ASSEMBLY
6RB1MTC *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8130
Bosch type code   EFEP215A
Nozzle   105780-0050
Bosch type code   DN6TD119NP1T
Nozzle holder   105780-2090
Bosch type code   EFEP215
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-1920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.6 3.55 3.65
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   12
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   281.4 279.4 283.4
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   6.4+-0.5
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   15 11.8 18.2
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Timer adjustment
Pump speed r/min   750--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   700
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1000
Advance angle deg.   2.2 1.7 2.7
Timer adjustment_04
Pump speed r/min   -
Advance angle deg.   4.5 4.5 4.5
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 106671-1430
N:Pump speed R:Rack position (mm) (1)Notch fixed: K (2)Do not adjust boost compensator spring.
----------
K=10
----------

Speed control lever angle

Test data 106671-1430
F:Full speed I:Idle S:Stop
----------

----------
a=8deg+-5deg b=28deg+-5deg c=32deg+-3deg

Stop lever angle

Test data 106671-1430
N:Pump normal S:Stop the pump.
----------

----------
a=19deg+-5deg b=53deg+-5deg

0000001101

Test data 106671-1430
N:Normal B:When boosted
----------

----------
a=(15deg) b=(15deg)

Timing setting

Test data 106671-1430
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=18deg
----------
a=(70deg)




Information:

Fuel consumption complaints are related to engine owners expectations. They may often times be related to the engine itself, causes other than the engine, and in some cases the fuel consumption may be normal for the application. Only a good discussion with the owner/operator, as described in the Owner/Operator Input section, will give guidance as to a correct repair or to prevent unnecessary repairs.Owner/Operator Input
The following are some of the questions which should be asked before beginning any diagnosis or repair for an engine performance complaint. There Are No Hard And Fast Answers For These Questions. There are many factors that can cause poor fuel mileage or make users believe they are getting fuel-poor-mileage.There are also a variety of customer expectations which are acceptable. The answers to these questions will give you a better understanding and perspective on the complaint and may identify characteristics which will help pinpoint the cause of the complaint quickly.1. Are miles measured accurately?A most common problem in determining mpg is errors in recording the number of miles traveled.A. Is this vehicle hub or cab odometer accurate? The easiest way to check an odometer is to install a hub odometer known to be accurate and for the tire size on the truck. Run the truck over several hundred miles and compare the reading with the original odometer.Odometers may also be checked by comparing them to interstate mile posts or by running over a course of known length-a 50-mile run is required to get a good check.B. Are "book miles" or "driver-paid miles" correct? Another way in which miles for mpg calculations are obtained by a fleet is the use of "book miles" or "driver-paid miles." The use of this system can short mileage accumulation by 10 to 15%; thus, mpg is low by 10 to 15%.C. Is the vehicle used for pick-up and delivery operation? Another problem affecting mileage accumulation in many fleets is the use of linehaul equipment for pickup and delivery operations. In the "book mile" system, the truck rarely gets credit for any miles run in pick-up and delivery.2. Is fuel measurement accurate?There are a number of ways in which fuel measurement can be the source of mpg problems.A. Are fuel pumps calibrated? If fuel tickets come from company-owned fuel pumps, there can be errors because nonrevenue fuel pumps do not have calibration requirements in many states.B. Are road fuel tickets accurate? The only way to verify fuel additions when road fuel tickets are used is a laborious ticket-by-ticket audit ensuring that the correct amount of fuel has been entered for the vehicles in question and that there are no indications of incorrect entries.C. Are tank-full mileage checks correctly done? The big problem in "tank-full" checks is getting the tank filled to the same level before and after the user "checked the mileage." With two 100 gallon tanks, errors of 5 to 10 gallons are very common in topping off tanks because of the way truck tanks crossfeed with a relatively

Have questions with 106671-1430?





Group cross 106671-1430 ZEXEL

Isuzu 

 
1156020020 
INJECTION-PUMP ASSEMBLY
6RA1X
 
1156020021 
INJECTION-PUMP ASSEMBLY
6RA1X
 
1156021290 
INJECTION-PUMP ASSEMBLY
6RA1X
 
1156021330 
INJECTION-PUMP ASSEMBLY
6RA1X
 
1156021331 
INJECTION-PUMP ASSEMBLY
6RA1X
 
1156021332 
INJECTION-PUMP ASSEMBLY
6RA1TC
9 400 616 704 
1156021333 
INJECTION-PUMP ASSEMBLY
6RA1-TC
 
1156019951 
INJECTION-PUMP ASSEMBLY
6RA1
 
1156019952 
INJECTION-PUMP ASSEMBLY
6RA1
 
1156019953 
INJECTION-PUMP ASSEMBLY
6RA1TC
 
1156021430 
INJECTION-PUMP ASSEMBLY
6RB1X
 
1156021431 
INJECTION-PUMP ASSEMBLY
6RB1X
 
1156021432 
INJECTION-PUMP ASSEMBLY
6RB1X
 
1156021433 
INJECTION-PUMP ASSEMBLY
6RB1TC
 
1156021434 
INJECTION-PUMP ASSEMBLY
6RB1TC
 
1156021435 
INJECTION-PUMP ASSEMBLY
6RB1-TC
 
1156021436 
INJECTION-PUMP ASSEMBLY
6RB1-TC
9 400 616 705 
1156021437 
INJECTION-PUMP ASSEMBLY
6RB1-TC
106671-1430  

106671-1431 
 
1156018460 
INJECTION-PUMP ASSEMBLY
6RB1MTC
9 400 616 706 
 
INJECTION-PUMP ASSEMBLY
6RB1MTC

Isuzu 

9 400 616 706 
1156018461 
INJECTION-PUMP ASSEMBLY
6RB1MTC
 
1156021420 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021421 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021422 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021423 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021424 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021425 
INJECTION-PUMP ASSEMBLY
6SD1TC
 
1156021426 
INJECTION-PUMP ASSEMBLY
6SD1-TC
 
1156021427 
INJECTION-PUMP ASSEMBLY
6SD1-TC2
 
1156021428 
INJECTION-PUMP ASSEMBLY
6SD1-TC2
9 400 616 707 
1156021429 
INJECTION-PUMP ASSEMBLY
6SD1-TC2
 
1156021011 
INJECTION-PUMP ASSEMBLY
6RB1-TC
 
1156021021 
INJECTION-PUMP ASSEMBLY
6RB1TC
 
1156021022 
INJECTION-PUMP ASSEMBLY
6RB1TC
9 400 616 708 
1899660349 
INJECTION-PUMP ASSEMBLY
6SD1MTC
 
1156023200 
INJECTION-PUMP ASSEMBLY
6RB1T
9 400 610 324 
1156023201 
INJECTION-PUMP ASSEMBLY
6RB1T
 
1156023870 
INJECTION-PUMP ASSEMBLY
6SD1MTC
F 019 Z20 396 
1156023871 
INJECTION-PUMP ASSEMBLY
6SD1MTC
Back to top