106661-0463 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1066610463 1670096605


 

Information injection-pump assembly

ZEXEL 106661-0463 1066610463
NISSAN-DIESEL 1670096605 1670096605
106661-0463 INJECTION-PUMP ASSEMBLY
Rating:
86
Buy INJECTION-PUMP ASSEMBLY 106661-0463 zexel genuine, new aftermarket engine parts with delivery

Service parts 106661-0463 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106066-1061
3. GOVERNOR 105306-0401
4. SUPPLY PUMP 105227-6010
5. AUTOM. ADVANCE MECHANIS 105614-0660
6. COUPLING PLATE 105662-0761
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-4050
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 19.6(200)
13. NOZZLE-HOLDER 105031-4270
14. NOZZLE 105015-2780
15. NOZZLE SET

Include in #1:

106661-0463 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
106661-0463 
 
1670096605  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
PE60 * K




Information:


Illustration 1 g00564355
7W-2743 Electronic Speed Switch (ESS)
(1) Push button for Overspeed Verification
(2) Reset button
(3) Overspeed indicator lamp
(4) Seal screw plug for adjusting the engine overspeed
(5) Seal screw plug for adjusting the crank terminate speed
(6) Seal screw plug for adjusting the oil step pressure speed setting The oil step speed calibration increases the oil step speed setting or the oil step speed calibration decreases the oil step speed setting. Refer to the Speed Specification Chart in order to find the oil step speed that is equal to the engine rpm when the engine is running.
Remove the lockwire and the seal from seal screw plug (6). Remove seal screw plug (6) from the access hole for the oil step speed adjusting screw.
Use a small screwdriver to lightly turn the oil step speed adjusting screw in the direction of the "MAX" arrow or the clockwise direction. Turn the screw twenty times. The oil step speed adjusting screw will vary the setting of a potentiometer that is inside of the ESS. The oil step speed adjusting screw will not cause damage to the potentiometer. Also, the screw can not be removed if the screw is turned in the wrong direction.
Connect a voltmeter with the positive lead at terminal (ESS-13) and the negative lead at (ESS-5). Use a 6V-7070 Digital Multimeter or a voltmeter with the same accuracy. Measure the voltage.
For a specific engine rating, find the engine rpm in the column for the oil step speed setting in the Speed Specification Chart. Run the engine at the rpm that is specified in the table.
While the engine is running, look into the hole for the adjustment of the oil step speed. A red indicator lamp should be lighted. A positive voltage should be observed on the multimeter 9 seconds after the indicator lamp is lighted. Turn the oil step speed adjusting screw clockwise until the indicator lamp turns off. The oil step speed setting is above the present rpm of the engine. Slowly turn the oil step speed adjusting screw counterclockwise until the indicator lamp is lighted. After a 9 second delay, a positive voltage should be observed on the multimeter. This position is the correct setting for the oil step speed.
Install seal screw plug (6) in the access hole for the oil step speed adjusting screw. Tighten the screw to a torque of 0.20 0.03 N m (1.8 .3 lb in). Install the lockwire and the seal if the overspeed calibration and the crank terminate speed calibration are also complete.

Have questions with 106661-0463?





Group cross 106661-0463 ZEXEL

Nissan-Diesel 

 
1670096100 
INJECTION-PUMP ASSEMBLY
PD6T
 
1670096101 

 
1671396505 
INJECTION-PUMP ASSEMBLY
PE60
 
1671396507 

 
1671396506 
INJECTION-PUMP ASSEMBLY
PE60
 
1670096512 
INJECTION-PUMP ASSEMBLY
PE60
 
1670096513 
INJECTION-PUMP ASSEMBLY
PE60
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

106661-0463  
 
1670096605 
INJECTION-PUMP ASSEMBLY
PE60
 
1671396508 
INJECTION-PUMP ASSEMBLY
PE60
 
1670096102 
INJECTION-PUMP ASSEMBLY
PD6T
 
1670096103 

PD6T
Back to top