104741-5380 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1047415380

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 104741-5380 1047415380

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 104741-5380 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

ZEXEL 104741-5380 1047415380

Zexel num

Bosch num

Firm num

Name

104741-5380

INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113orSAEJ967d

Test oil temperature degC 45 45 50

Nozzle 105780-0060

Bosch type code NP-DN0SD1510

Nozzle holder 105780-2150

Opening pressure MPa 13 13 13.3

Opening pressure kgf/cm2 133 133 136

Injection pipe 157805-7320

Injection pipe
Inside diameter - outside diameter - length (mm) mm 2-6-450

Joint assembly 157641-4720

Tube assembly 157641-4020

Transfer pump pressure kPa 20 20 20

Transfer pump pressure kgf/cm2 0.2 0.2 0.2

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Pump speed r/min 1075 1075 1075

Average injection quantity mm3/st. 45.3 44.8 45.8

Difference in delivery mm3/st. 3.5

Basic *

Oil temperature degC 50 48 52

Injection timing adjustment_02

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 36.1 36.1 36.1

Oil temperature degC 48 46 50

Injection timing adjustment_03

Pump speed r/min 1075 1075 1075

Average injection quantity mm3/st. 45.3 44.3 46.3

Difference in delivery mm3/st. 3.5

Basic *

Oil temperature degC 50 48 52

Injection timing adjustment_04

Pump speed r/min 1500 1500 1500

Average injection quantity mm3/st. 51.6 51.6 51.6

Oil temperature degC 50 48 52

Injection timing adjustment_05

Pump speed r/min 1800 1800 1800

Average injection quantity mm3/st. 55.4 55.4 55.4

Oil temperature degC 50 48 52

Injection quantity adjustment

Pump speed r/min 2300 2300 2300

Average injection quantity mm3/st. 18 15 21

Difference in delivery mm3/st. 5.5

Basic *

Oil temperature degC 52 50 54

Injection quantity adjustment_02

Pump speed r/min 2500 2500 2500

Average injection quantity mm3/st. 6

Oil temperature degC 55 52 58

Injection quantity adjustment_03

Pump speed r/min 2300 2300 2300

Average injection quantity mm3/st. 18 15 21

Difference in delivery mm3/st. 5.5

Oil temperature degC 52 50 54

Governor adjustment

Pump speed r/min 385 385 385

Average injection quantity mm3/st. 7.5 5.5 9.5

Difference in delivery mm3/st. 2

Basic *

Oil temperature degC 48 46 50

Governor adjustment_02

Pump speed r/min 385 385 385

Average injection quantity mm3/st. 7.5 5.5 9.5

Difference in delivery mm3/st. 2

Oil temperature degC 48 46 50

Timer adjustment

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 60 60 100

Basic *

Oil temperature degC 48 46 50

Remarks
IDLE

Timer adjustment_02

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 80 60 100

Oil temperature degC 48 46 50

Speed control lever angle

Pump speed r/min 385 385 385

Average injection quantity mm3/st. 0 0 0

Oil temperature degC 48 46 50

Remarks
Magnet OFF at idling position

0000000901

Pump speed r/min 1300 1300 1300

Oil temperature degC 50 48 52

Remarks
MEASURE

Stop lever angle

Pump speed r/min 1300 1300 1300

Pressure kPa 441 421 461

Pressure kgf/cm2 4.5 4.3 4.7

Basic *

Oil temperature degC 50 48 52

Stop lever angle_02

Pump speed r/min 1300 1300 1300

Pressure kPa 441 421 461

Pressure kgf/cm2 4.5 4.3 4.7

Basic *

Oil temperature degC 50 48 52

0000001101

Pump speed r/min 1300 1300 1300

Timer stroke mm 4.2 4 4.4

Basic *

Oil temperature degC 50 48 52

_02

Pump speed r/min 850 850 850

Timer stroke mm 0.5 0.1 1.3

Oil temperature degC 50 48 52

_03

Pump speed r/min 1300 1300 1300

Timer stroke mm 4.2 4 4.4

Basic *

Oil temperature degC 50 48 52

_04

Pump speed r/min 1900 1900 1900

Timer stroke mm 8.6 8.3 9

Oil temperature degC 50 48 52

0000001201

Max. applied voltage V 8 8 8

Test voltage V 13 12 14

Timing setting

K dimension mm 3.1 3 3.2

KF dimension mm 5.5 5.4 5.6

MS dimension mm 0.8 0.7 0.9

Pre-stroke mm 0.45 0.43 0.47

Control lever angle alpha deg. 18 14 22

Control lever angle beta deg. 37 32 42

Information:

PARTS NEEDED
Qty
Part Number Description
6 10R7222 INJECTOR GP-FUEL
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 18% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.
ACTION REQUIRED
Take the following actions before or after a failure occurs on one or more injectors in any of the machines listed in this service letter.
- If one or more injectors fail it may be necessary to replace up to 6 injectors at the time of repair.
There will be situations when all 6 injectors do not have to be replaced. Refer to next paragraph to determine which injectors should be replaced.
- If an injector repair has previously been performed after approximately 01Oct07 on any of the listed machines, only the injectors that were not replaced at that time should be replaced. This should further be verified by comparing the injector serial numbers in the engine to a range of 3B115776403B to 3B11676551F9. Disregard the first and last two characters in the serial number (in this case "3B" and "3B" in the first serial number and "3B" and "F9" in the second serial number). The reason for verifying the serial number range is due to a batch change of the internal part that is failing. The change was made after serial number 3B11676551F9.
Only injectors falling within the range of 11577640-11676551 should be replaced.
- If the suspect injector can not be identified by using the automatic cylinder cutout test use the two methods below.
- First, run a manual cylinder cutout test at a high engine speed with some load on the engine. When the injector that has failed is cutout, the sound of the engine should be more normal as opposed to the loud knocking heard when the failed injector is active. The second method is to unplug the wiring harness at the valve cover base that sends current to the injector solenoids as well as the harness connection for the injection actuation pressure sensor. By making these disconnections, the fuel injectors will not fire and the HEUI pump will go to maximum actuation pressure. Then remove the valve cover and crank the engine. The injectors that have failed should expel more oil (from the HEUI System) than those that are not failed.
-Refer to RENR9579 for removal/install procedure of the unit injector.
-The serial number of all injectors replaced in a machine covered under this service letter must be documented in the claims story.
SERVICE CLAIM ALLOWANCES
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
0-1000 hrs,
0-24 mo 100.0% 100.0% 0.0% 0.0% 0.0% 0.0%
This is a 4.0-hour job
The serial number of any injector(s) replaced in a machine covered under this service letter must be documented in the claims story. Only injectors with serial numbers between 11577640-11676551 (see action required for explanation on how to decode injector serial number) will be