104741-4930 ZEXEL F 01G 09W 0FE BOSCH INJECTION-PUMP ASSEMBLY f01g09w0fe 1047414930 16700na00a

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH F 01G 09W 0FE f01g09w0fe

ZEXEL 104741-4930 1047414930

NISSAN-DIESEL 16700NA00A 16700na00a

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 104741-4930 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104741-4930
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105148-1221
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)	9.8(100)
10.	NOZZLE-HOLDER	105078-0050
11.	NOZZLE	105007-1210

Scheme ###:

1/6.	[1]	146601-0900	PACKING RING
6.	[1]	146100-0020	SUPPLY PUMP
9.	[1]	146103-0000	COVER
10.	[2]	139104-0000	FLAT-HEAD SCREW
12.	[1]	146200-0020	DRIVE SHAFT
12/1.	[1]	146200-0000	DRIVE SHAFT
12/2.	[1]	146201-0000	WOODRUFF KEY
12/3.	[2]	146202-0100	DAMPER
12/4.	[1]	146203-0000	TOOTHED GEAR
17.	[1]	146204-0000	PLAIN WASHER
20.	[1]	146210-1720	ROLLER SET
24.	[1]	146303-0100	BEARING PIN
25.	[1]	146304-0000	BEARING PIN
26.	[1]	146305-0000	CLAMPING BAND
27.	[1]	146205-0000	SLOTTED WASHER
29.	[1]	146220-4520	CAM PLATE
30.	[1]	146600-0800	O-RING
31.	[1]	146300-4300	PUMP PLUNGER
32.	[1]	146301-0000	SLIDING PIECE
33.	[1]	146603-0700	SHIM
34.	[1]	146306-3100	COMPRESSION SPRING
35/1.	[0]	146603-0700	SHIM D17.5&7.5T0.60
35/1.	[0]	146603-0800	SHIM D17.5&7.5T0.70
35/1.	[0]	146603-0900	SHIM D17.5&7.5T0.90
35/1.	[0]	146603-1000	SHIM D17.5&7.5T1.00
35/1.	[0]	146603-1100	SHIM D17.5&7.5T1.20
35/1.	[0]	146603-3600	SHIM D17.5&7.5T2.40
36.	[1]	146600-0800	O-RING
37.	[1]	146310-0700	COVER
38.	[2]	146620-5000	BLEEDER SCREW
39.	[1]	146310-0100	COVER
40.	[2]	146620-5000	BLEEDER SCREW
43.	[1]	146230-0000	SHIM
44.	[1]	146230-0100	PLAIN WASHER
45.	[1]	146231-0001	SLOTTED WASHER
47.	[2]	146233-0000	SLOTTED WASHER
48/1.	[1]	146603-0100	SHIM D17.0&5.2T0.80
48/1.	[1]	146603-0200	SHIM D17.0&5.2T1.00
48/1.	[1]	146603-0300	SHIM D17.0&5.2T1.20
48/1.	[1]	146603-0400	SHIM D17.0&5.2T1.50
48/1.	[1]	146690-1400	SHIM D17&5.2T0.9
48/1.	[1]	146690-1500	SHIM D17&5.2T1.1
48/1.	[1]	146690-1600	SHIM D17&5.2T1.3
48/1.	[1]	146690-1700	SHIM D17&5.2T1.4
48/1.	[1]	146690-1800	SHIM D17&5.2T1.6
49.	[2]	146234-0600	GUIDE PIN
50.	[1]	146401-4220	HYDRAULIC HEAD
50.	[1]	146401-4220	HYDRAULIC HEAD
50.	[1]	146401-4220	HYDRAULIC HEAD
51.	[1]	146600-0000	O-RING
52/1.	[1]	146420-0700	SHIM D9.5&3.0T2.04
52/1.	[1]	146420-0800	SHIM D9.5&3.0T2.06
52/1.	[1]	146420-0900	SHIM D9.5&3.0T2.08
52/1.	[1]	146420-1000	SHIM D9.5&3.0T2.10
52/1.	[1]	146420-1100	SHIM D9.5&3.0T2.12
52/1.	[1]	146420-1200	SHIM D9.5&3.0T2.14
52/1.	[1]	146420-1300	SHIM D9.5&3.0T2.16
52/1.	[1]	146420-1400	SHIM D9.5&3.0T2.18
52/1.	[1]	146420-1500	SHIM D9.5&3.0T2.20
52/1.	[1]	146420-1600	SHIM D9.5&3.0T2.22
52/1.	[1]	146420-1700	SHIM D9.5&3.0T2.24
52/1.	[1]	146420-1800	SHIM D9.5&3.0T2.26
52/1.	[1]	146420-1900	SHIM D9.5&3.0T2.28
52/1.	[1]	146420-2000	SHIM D9.5&3.0T2.30
52/1.	[1]	146420-2100	SHIM D9.5&3.0T2.32
52/1.	[1]	146420-2200	SHIM D9.5&3.0T2.34
52/1.	[1]	146420-2400	SHIM D9.5&3.0T2.38
52/1.	[1]	146420-2500	SHIM D9.5&3.0T2.40
52/1.	[1]	146420-2600	SHIM D9.5&3.0T2.42
52/1.	[1]	146420-2700	SHIM D9.5&3.0T2.44
52/1.	[1]	146420-2800	SHIM D9.5&3.0T2.46
52/1.	[1]	146420-2900	SHIM D9.5&3.0T2.48
52/1.	[1]	146420-3000	SHIM D9.5&3.0T2.50
52/1.	[1]	146420-3100	SHIM D9.5&3.0T2.52
52/1.	[1]	146420-3200	SHIM D9.5&3.0T2.54
52/1.	[1]	146420-3300	SHIM D9.5&3.0T2.56
52/1.	[1]	146420-3400	SHIM D9.5&3.0T2.58
52/1.	[1]	146420-3500	SHIM D9.5&3.0T2.60
52/1.	[1]	146420-3600	SHIM D9.5&3.0T2.62
52/1.	[1]	146420-3700	SHIM D9.5&3.0T2.64
52/1.	[1]	146420-3800	SHIM D9.5&3.0T2.66
52/1.	[1]	146420-3900	SHIM D9.5&3.0T2.68
52/1.	[1]	146420-4000	SHIM D9.5&3.0T2.70
52/1.	[1]	146420-4100	SHIM D9.5&3.0T2.72
54.	[4]	146433-0100	GASKET
55.	[4]	146430-0320	DELIVERY-VALVE ASSEMBLY VE4
56.	[4]	146432-0200	COMPRESSION SPRING
58.	[4]	146440-0720	FITTING
60.	[4]	139106-0100	FLAT-HEAD SCREW
67.	[1]	146822-0220	GOVERNOR COVER
67/1.	[1]	146805-2120	GOVERNOR COVER
67/2.	[1]	146515-0320	CONTROL SHAFT
67/3.	[1]	146600-0100	O-RING
67/4.	[2]	139310-0200	PLAIN WASHER
67/4.	[2]	139310-0200	PLAIN WASHER
67/5.	[1]	146530-0000	CONTROL LEVER
67/5B.	[1]	146530-0100	CONTROL LEVER STAMP 001
67/5C.	[1]	146832-1500	CONTROL LEVER
67/5D.	[1]	146832-1600	CONTROL LEVER
67/6.	[2]	014110-6440	LOCKING WASHER D12.2&6.1T1.5
67/6.	[2]	014110-6440	LOCKING WASHER D12.2&6.1T1.5
67/7.	[1]	013020-6040	UNION NUT
67/8.	[1]	146515-1820	LEVER SHAFT
67/9.	[1]	146592-0400	COILED SPRING
67/10.	[1]	146600-0200	O-RING
67/11.	[1]	146602-0100	PLAIN WASHER
67/12.	[1]	146540-4000	CONTROL LEVER
67/12B.	[1]	146540-4100	CONTROL LEVER
67/13.	[1]	146621-1700	UNION NUT
67/14.	[1]	146621-1700	UNION NUT
67/15.	[1]	146526-2800	BLEEDER SCREW
67/16.	[1]	146526-6400	BLEEDER SCREW
67/18.	[1]	146594-0600	COILED SPRING
67/19.	[1]	146541-0000	ANGLE PIECE
67/25.	[2]	013020-6040	UNION NUT
67/25.	[2]	013020-6040	UNION NUT
67/26.	[1]	139006-0200	BLEEDER SCREW
67/78.	[1]	146600-4400	SEAL RING
67/104.	[1]	146936-1100	BRACKET
67/105.	[1]	010206-1040	HEX-SOCKET-HEAD CAP SCREW
67/200.	[1]	139308-0300	PLAIN WASHER
67/201.	[1]	146545-3400	THREADED PIN L53.00
67/201B.	[1]	146545-3500	THREADED PIN L55.00
67/201C.	[1]	146545-3600	THREADED PIN L57.00
67/202.	[1]	139208-0900	UNION NUT
67/203.	[1]	146600-1200	O-RING
95.	[1]	146891-1820	FULCRUM LEVER
104.	[2]	146568-0000	SLOTTED SPRING PIN
105.	[2]	026508-1140	GASKET D11.4&8.2T1.0
106.	[2]	146588-0500	COILED SPRING
107.	[1]	146569-0300	UNION NUT
108.	[1]	146570-0420	GOVERNOR SHAFT
109.	[1]	146600-0400	O-RING
110/1.	[1]	146571-0000	SHIM D20.2&8.3T1.05
110/1.	[1]	146571-0100	SHIM D20.2&8.3T1.25
110/1.	[1]	146571-0200	SHIM D20.2&8.3T1.45
110/1.	[1]	146571-0300	SHIM D20.2&8.3T1.65
110/1.	[1]	146571-0400	SHIM D20.2&8.3T1.85
111.	[1]	146602-0600	PLAIN WASHER
112.	[1]	146572-0020	FLYWEIGHT ASSEMBLY
114.	[1]	146602-2600	PLAIN WASHER
115.	[1]	146976-2800	SLIDING SLEEVE
116.	[1]	146576-0400	CAP
117/1.	[1]	146877-1020	PLUG L=5.2
117/1.	[1]	146877-1120	PLUG L=5.3
117/1.	[1]	146877-1220	PLUG L=5.4
117/1.	[1]	146877-1320	PLUG L=5.5
117/1.	[1]	146877-1420	PLUG L=5.6
117/1.	[1]	146877-1520	PLUG L=5.7
117/1.	[1]	146877-1620	PLUG L=5.8
117/1.	[1]	146877-1720	PLUG L=5.9
117/1.	[1]	146877-1820	PLUG L=6.0
117/1.	[1]	146877-1920	PLUG L=6.1
117/1.	[1]	146877-2020	PLUG L=6.2
117/1.	[1]	146877-2120	PLUG L=6.3
117/1.	[1]	146877-2220	PLUG L=6.4
117/1.	[1]	146877-2320	PLUG L=6.5
117/1.	[1]	146877-2420	PLUG L=6.6
117/1.	[1]	146877-2520	PLUG L=6.7
117/1.	[1]	146877-2620	PLUG L=6.8
120.	[1]	146579-2720	RETAINING PIN
122.	[1]	146580-4100	GOVERNOR SPRING
123.	[4]	139106-0200	FLAT-HEAD SCREW
130.	[1]	146421-0020	CAPSULE
130/2.	[1]	026508-1140	GASKET D11.4&8.2T1.0
130/3.	[1]	146422-0000	BLEEDER SCREW
130/4.	[1]	146600-0500	O-RING
133.	[1]	146600-0600	O-RING
134.	[1]	146600-0700	O-RING
135.	[1]	146110-0520	CONTROL VALVE
135/5.	[1]	146114-0000	SPRING WASHER
136.	[1]	146120-0120	OVER FLOW VALVE
200.	[1]	146206-0100	COILED SPRING
240.	[1]	146650-0720	PULLING ELECTROMAGNET
240/8.	[1]	146600-1700	O-RING
242.	[1]	146662-8320	WIRE
243.	[1]	146621-4901	UNION NUT
246.	[1]	027412-2440	EYE BOLT
800S.	[1]	146019-8820	PUMP HOUSING
800S/1/6.	[1]	146601-0900	PACKING RING
804S.	[1]	146232-1520	COMPRESSION SPRING
805S.	[1]	146574-0320	PARTS SET
810S.	[1]	146600-1120	REPAIR SET
821S.	[1]	146210-5720	ROLLER SET
835S.	[1]	146598-1000	CAP
836S/1.	[1]	146598-0600	CAP L18
836S/1.	[1]	146598-0700	CAP L21
836S/1.	[1]	146598-0800	CAP L24
836S/1.	[1]	146598-0900	CAP L27
906.	[1]	146984-7200	NAMEPLATE
907.	[1]	025803-1640	WOODRUFF KEY

Include in #2:

104741-4930 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 01G 09W 0FE f01g09w0fe

ZEXEL 104741-4930 1047414930

NISSAN-DIESEL 16700NA00A 16700na00a

Zexel num

Bosch num

Firm num

Name

104741-4930

F 01G 09W 0FE

16700NA00A NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
QD32 K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113orSAEJ967d

Test oil temperature degC 45 45 50

Nozzle 105780-0060

Bosch type code NP-DN0SD1510

Nozzle holder 105780-2150

Opening pressure MPa 13 13 13.3

Opening pressure kgf/cm2 133 133 136

Injection pipe 157805-7320

Injection pipe
Inside diameter - outside diameter - length (mm) mm 2-6-450

Joint assembly 157641-4720

Tube assembly 157641-4020

Transfer pump pressure kPa 20 20 20

Transfer pump pressure kgf/cm2 0.2 0.2 0.2

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 54 53.5 54.5

Difference in delivery mm3/st. 4.5

Basic *

Oil temperature degC 50 48 52

Injection timing adjustment_02

Pump speed r/min 400 400 400

Average injection quantity mm3/st. 50 50 50

Oil temperature degC 48 46 50

Injection timing adjustment_03

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 50.6 46.6 54.6

Oil temperature degC 48 46 50

Injection timing adjustment_04

Pump speed r/min 750 750 750

Average injection quantity mm3/st. 52.1 52.1 52.1

Oil temperature degC 50 48 52

Injection timing adjustment_05

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 54 53 55

Difference in delivery mm3/st. 5

Basic *

Oil temperature degC 50 48 52

Injection timing adjustment_06

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 52.9 49.4 56.4

Oil temperature degC 50 48 52

Injection quantity adjustment

Pump speed r/min 1225 1225 1225

Average injection quantity mm3/st. 13.4 11.4 15.4

Difference in delivery mm3/st. 4

Basic *

Oil temperature degC 50 48 52

Injection quantity adjustment_02

Pump speed r/min 1400 1400 1400

Average injection quantity mm3/st. 5

Oil temperature degC 50 48 52

Injection quantity adjustment_03

Pump speed r/min 1225 1225 1225

Average injection quantity mm3/st. 13.4 9.9 16.9

Basic *

Oil temperature degC 50 48 52

Governor adjustment

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 11.8 9.8 13.8

Difference in delivery mm3/st. 2

Basic *

Oil temperature degC 48 46 50

Governor adjustment_02

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 11.8 9.3 14.3

Difference in delivery mm3/st. 2.5

Basic *

Oil temperature degC 48 46 50

Timer adjustment

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 56.9 51.9 61.9

Basic *

Oil temperature degC 48 46 50

Remarks
Full

Timer adjustment_02

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 56.9 51.9 61.9

Oil temperature degC 48 46 50

Remarks
Full

Speed control lever angle

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 0 0 0

Oil temperature degC 48 46 50

Remarks
Magnet OFF at idling position

0000000901

Pump speed r/min 900 900 900

Overflow quantity cm3/min 440 310 570

Oil temperature degC 50 48 52

Stop lever angle

Pump speed r/min 900 900 900

Pressure kPa 549 520 578

Pressure kgf/cm2 5.6 5.3 5.9

Basic *

Oil temperature degC 50 48 52

Stop lever angle_02

Pump speed r/min 900 900 900

Pressure kPa 549 510 588

Pressure kgf/cm2 5.6 5.2 6

Basic *

Oil temperature degC 50 48 52

Stop lever angle_03

Pump speed r/min 1000 1000 1000

Pressure kPa 588 549 627

Pressure kgf/cm2 6 5.6 6.4

Oil temperature degC 50 48 52

0000001101

Pump speed r/min 900 900 900

Timer stroke mm 2 1.8 2.2

Basic *

Oil temperature degC 50 48 52

_02

Pump speed r/min 800 800 800

Timer stroke mm 1.3 0.7 1.9

Oil temperature degC 50 48 52

_03

Pump speed r/min 900 900 900

Timer stroke mm 2 1.6 2.4

Basic *

Oil temperature degC 50 48 52

_04

Pump speed r/min 1000 1000 1000

Timer stroke mm 2.5 1.9 3.1

Oil temperature degC 50 48 52

0000001201

Max. applied voltage V 8 8 8

Test voltage V 13 12 14

0000001401

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 36 35.5 36.5

Timer stroke TA mm 1.5 1.3 1.7

Timer stroke variation dT mm 0.5 0.5 0.5

Basic *

Oil temperature degC 50 48 52

_02

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 36 35 37

Timer stroke TA mm 1.5 1.1 1.9

Timer stroke variation dT mm 0.5 0.5 0.5

Basic *

Oil temperature degC 50 48 52

_03

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 23 20.5 25.5

Timer stroke TA mm 0.7 0.1 1.3

Timer stroke variation dT mm 1.3 1.3 1.3

Oil temperature degC 50 48 52

Timing setting

K dimension mm 3.3 3.2 3.4

KF dimension mm 5.62 5.52 5.72

MS dimension mm 1.8 1.7 1.9

Pre-stroke mm 0.1 0.08 0.12

Control lever angle alpha deg. 25 21 29

Control lever angle beta deg. 30 25 35

Test data Ex:

0000001801 STOP LEVER ADJUSTMENT

Adjustment of the stop lever Adjust adjusting bolt (B) so that the starting injection quantity is within the standard. Fix using nut. (A) Adjusting nut (C) Starting injection quantity adjusting lever
----------

----------
L=15.0~18.5mm

Information:

This Program must be administered as soon as possible. When reporting the repair, use "PI3330" as the Part Number, "7751" as the Group Number, "56" as the Warranty Claim Description Code and "T" as the SIMS Description Code. Exception: If the repair is done after failure, use "PI3330" as the Part Number, "7751" as the Group Number, "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.
Completion Date
March 31, 2000Termination Date
September 30, 2000Problem
The torque of the injector electronic solenoid valves need to be checked. The valve has four Torx bolts that hold the stator to the housing. If these bolts are not properly tightened, fuel can leak into the oil.
Affected Product
Model & Identification Number
D11R (9TR441-442)
776D (5ER126, 5ER127)
785C (1HW122)
793C (4GZ165-167)
777D (3PR1058, 3PR1057, 3PR1061, 3PR1059, 3PR1060, 3PR1063)
3508B (3DM157-159 4GM426-439 6PN532-533 , 6PN535-536, 6PN539-540, 6PN542-543 5PS225-234 2HW125-126 1FZ366-370 )
3512 (6PM38-39 3MS186 3RS329 )
3512B (8EM317-318 8RM395-397 4TM215-217 3ZW131-134 6WN349-356 )
3516 (7KM50-51 3SS306-307 )
3516B (6HN384, 6HN390, 6HN392, 6HN394, 6HN398 7RN818-819 , 7RN821, 7RN824, 7RN826-827, 7RN833, 7RN836-840, 7RN850, 7RN852 8KN368-369 , 8KN372, 8KN373 7TR818 4BW333-334 )
Parts Needed
Dealers will not need to order parts for this Program.
Action Required
See the attached procedure.
Owner Notification
U.S. and Canadian owners will receive the attached Owner Notification.
Service Claim Allowances
This is a 3-hour job.
U.S. and Canadian Dealers Only - Eligible dealers may enter a Type 2 SIMS Report.
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE.
Attach.(1-Owner Notification)(Torque Procedure)Copy Of Owner Notification For U.S. And Canadian Owners
Torque Procedure For Electronic 3500B Injector Bolts
THIS REWORK IS RESTRICTED TO ENGINES LISTED IN THE AFFECTED PRODUCT ONLY.
THIS PIP DOES NOT ALLOW FOR THE REMOVAL OF THE INJECTOR. DO NOT REMOVE ANY OF THE STATOR BOLTS. THIS WILL VOID INJECTOR WARRANTY.
PROCEDURE:
1. Remove the valve covers to reveal the injector assembly/ electronic valve.2. Remove electronic valve terminal connector (two retaining nuts) with a " universal socket. Take the terminal connectors off of the posts.3. The four stator retaining bolts you need to check are now accessible. To properly complete the torque check, the following tools are required.a) Click torque wrench, " drive (capable of accurately measuring 2.0 N m)b) 6" extension " drive.c) universal joint, "drived) T10 Torx bit, " drive4. Set the torque wrench value to (2.1 N m). Check all four bolts and tighten (if needed) until they reach the 2.1 specification.:
DO NOT OVER TORQUE THE STATOR RETAINING BOLTS (2.1 N m). THIS COULD CAUSE FURTHER DAMAGE.
5. Reassemble the engine in the reverse order.a) Torque value of the terminal connector nuts - 3.0 N m b) Torque value for the valve cover bolts - 47 9 N m.