104740-2950 ZEXEL 9 460 611 416 BOSCH INJECTION-PUMP ASSEMBLY 9460611416 1047402950

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 460 611 416 9460611416

ZEXEL 104740-2950 1047402950

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 104740-2950 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104740-2950
1.	_
2.	FUEL INJECTION PUMP	104640-2950
3.	NUMBER PLATE	146980-6900
4.	_	146672-6120
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105140-1070
8.	Nozzle and Holder	16600-59Y11
9.	Open Pre:MPa(Kqf/cm2)	12.7{130}
10.	NOZZLE-HOLDER	105071-1361
11.	NOZZLE	105000-2270

Scheme ###:

1/6.	[1]	146601-0900	PACKING RING
6.	[1]	146100-0320	SUPPLY PUMP
9.	[1]	146103-0100	COVER
10.	[2]	139104-0000	FLAT-HEAD SCREW
12.	[1]	146200-0020	DRIVE SHAFT
12/1.	[1]	146200-0000	DRIVE SHAFT
12/2.	[1]	146201-0000	WOODRUFF KEY
12/3.	[2]	146202-0100	DAMPER
12/4.	[1]	146203-0000	TOOTHED GEAR
17.	[1]	146204-0000	PLAIN WASHER
20.	[1]	146210-2420	ROLLER SET
24.	[1]	146303-0000	BEARING PIN
25.	[1]	146304-0000	BEARING PIN
26.	[1]	146305-0000	CLAMPING BAND
27.	[1]	146205-0000	SLOTTED WASHER
29.	[1]	146220-2220	CAM PLATE
30.	[1]	146600-0800	O-RING
31.	[1]	146311-6220	PUMP PLUNGER
32.	[1]	146301-0000	SLIDING PIECE
34.	[1]	146312-2600	COMPRESSION SPRING
34B.	[1]	146312-2700	COMPRESSION SPRING
35/1.	[1]	146690-3200	SHIM D11.5&9.4T0.1
35/1.	[1]	146690-3300	SHIM D11.5&9.4T0.2
35/1.	[1]	146690-3400	SHIM D11.5&9.4T0.25
35/1.	[1]	146690-3500	SHIM D11.5&9.4T1.0
35/1.	[1]	146690-4100	SHIM D11.5&9.4T2
35/1.	[1]	146690-4200	SHIM D11.5&9.4T0.5
35/1.	[1]	146690-4300	SHIM D11.5&9.4T0.75
36.	[1]	146600-0800	O-RING
37.	[1]	146310-1600	COVER
38.	[2]	146620-5000	BLEEDER SCREW
39.	[1]	146310-0100	COVER
40.	[2]	146620-5000	BLEEDER SCREW
41.	[1]	146312-1900	COMPRESSION SPRING
42.	[1]	146602-8500	PLAIN WASHER
43.	[1]	146230-0000	SHIM
44.	[1]	146230-0100	PLAIN WASHER
45.	[1]	146231-0001	SLOTTED WASHER
47.	[2]	146233-0000	SLOTTED WASHER
48/1.	[1]	146603-0000	SHIM D17.0&5.2T0.50
48/1.	[1]	146603-0100	SHIM D17.0&5.2T0.80
48/1.	[1]	146603-0200	SHIM D17.0&5.2T1.00
48/1.	[1]	146603-0300	SHIM D17.0&5.2T1.20
48/1.	[1]	146603-0400	SHIM D17.0&5.2T1.50
48/1.	[1]	146603-0500	SHIM D17.0&5.2T1.80
48/1.	[1]	146603-0600	SHIM D17.0&5.2T2.00
48/1.	[1]	146690-1400	SHIM D17&5.2T0.9
48/1.	[1]	146690-1500	SHIM D17&5.2T1.1
48/1.	[1]	146690-1600	SHIM D17&5.2T1.3
48/1.	[1]	146690-1700	SHIM D17&5.2T1.4
48/1.	[1]	146690-1800	SHIM D17&5.2T1.6
48/1.	[1]	146690-1900	SHIM D17&5.2T1.7
48/1.	[1]	146690-5800	SHIM
48/1.	[1]	146690-5900	SHIM
48/1.	[1]	146690-6000	SHIM
48/1.	[1]	146690-6100	SHIM
48/1.	[1]	146690-6200	SHIM
48/1.	[1]	146690-6300	SHIM
48/1.	[1]	146690-6400	SHIM
48/1.	[1]	146690-6500	SHIM
48/1.	[1]	146690-6600	SHIM
48/1.	[1]	146690-6700	SHIM
48/1.	[1]	146690-6800	SHIM
48/1.	[1]	146690-6900	SHIM
48/1.	[1]	146690-7000	SHIM
48/1.	[1]	146690-7100	SHIM
48/1.	[1]	146690-7200	SHIM
48/1.	[1]	146690-7300	SHIM
48/1.	[1]	146690-7400	SHIM
48/1.	[1]	146690-7500	SHIM
48/1.	[1]	146690-7800	SHIM
49.	[2]	146234-0120	GUIDE PIN
50.	[1]	146403-3420	HYDRAULIC HEAD
50.	[1]	146403-3420	HYDRAULIC HEAD
50.	[1]	146403-3420	HYDRAULIC HEAD
51.	[1]	146600-0000	O-RING
52/1.	[1]	146420-0000	SHIM D9.5&3.0T1.90
52/1.	[1]	146420-0100	SHIM D9.5&3.0T1.92
52/1.	[1]	146420-0200	SHIM D9.5&3.0T1.94
52/1.	[1]	146420-0300	SHIM D9.5&3.0T1.96
52/1.	[1]	146420-0400	SHIM D9.5&3.0T1.98
52/1.	[1]	146420-0500	SHIM D9.5&3.0T2.00
52/1.	[1]	146420-0600	SHIM D9.5&3.0T2.02
52/1.	[1]	146420-0700	SHIM D9.5&3.0T2.04
52/1.	[1]	146420-0800	SHIM D9.5&3.0T2.06
52/1.	[1]	146420-0900	SHIM D9.5&3.0T2.08
52/1.	[1]	146420-1000	SHIM D9.5&3.0T2.10
52/1.	[1]	146420-1100	SHIM D9.5&3.0T2.12
52/1.	[1]	146420-1200	SHIM D9.5&3.0T2.14
52/1.	[1]	146420-1300	SHIM D9.5&3.0T2.16
52/1.	[1]	146420-1400	SHIM D9.5&3.0T2.18
52/1.	[1]	146420-1500	SHIM D9.5&3.0T2.20
52/1.	[1]	146420-1600	SHIM D9.5&3.0T2.22
52/1.	[1]	146420-1700	SHIM D9.5&3.0T2.24
52/1.	[1]	146420-1800	SHIM D9.5&3.0T2.26
52/1.	[1]	146420-1900	SHIM D9.5&3.0T2.28
52/1.	[1]	146420-2000	SHIM D9.5&3.0T2.30
52/1.	[1]	146420-2100	SHIM D9.5&3.0T2.32
52/1.	[1]	146420-2200	SHIM D9.5&3.0T2.34
52/1.	[1]	146420-2300	SHIM D9.5&3.0T2.36
52/1.	[1]	146420-2400	SHIM D9.5&3.0T2.38
52/1.	[1]	146420-2500	SHIM D9.5&3.0T2.40
52/1.	[1]	146420-2600	SHIM D9.5&3.0T2.42
52/1.	[1]	146420-2700	SHIM D9.5&3.0T2.44
52/1.	[1]	146420-2800	SHIM D9.5&3.0T2.46
52/1.	[1]	146420-2900	SHIM D9.5&3.0T2.48
52/1.	[1]	146420-3000	SHIM D9.5&3.0T2.50
52/1.	[1]	146420-3100	SHIM D9.5&3.0T2.52
52/1.	[1]	146420-3200	SHIM D9.5&3.0T2.54
52/1.	[1]	146420-3300	SHIM D9.5&3.0T2.56
52/1.	[1]	146420-3400	SHIM D9.5&3.0T2.58
52/1.	[1]	146420-3500	SHIM D9.5&3.0T2.60
52/1.	[1]	146420-3600	SHIM D9.5&3.0T2.62
52/1.	[1]	146420-3700	SHIM D9.5&3.0T2.64
52/1.	[1]	146420-3800	SHIM D9.5&3.0T2.66
52/1.	[1]	146420-3900	SHIM D9.5&3.0T2.68
52/1.	[1]	146420-4000	SHIM D9.5&3.0T2.70
52/1.	[1]	146420-4100	SHIM D9.5&3.0T2.72
52/1.	[1]	146420-4200	SHIM D9.5&3.0T2.74
52/1.	[1]	146420-4300	SHIM D9.5&3.0T2.76
52/1.	[1]	146420-4400	SHIM D9.5&3.0T2.78
52/1.	[1]	146420-4500	SHIM D9.5&3.0T2.80
52/1.	[1]	146420-4600	SHIM D9.5&3.0T2.82
52/1.	[1]	146420-4700	SHIM D9.5&3.0T2.84
52/1.	[1]	146420-4800	SHIM D9.5&3.0T2.86
52/1.	[1]	146420-4900	SHIM D9.5&3.0T2.88
52/1.	[1]	146420-5000	SHIM D9.5&3.0T2.90
52/1.	[1]	146420-5100	SHIM D9.5&3.0T1.74
52/1.	[1]	146420-5200	SHIM D9.5&3.0T1.76
52/1.	[1]	146420-5300	SHIM D9.5&3.0T1.78
52/1.	[1]	146420-5400	SHIM D9.5&3.0T1.80
52/1.	[1]	146420-5500	SHIM D9.5&3.0T1.82
52/1.	[1]	146420-5600	SHIM D9.5&3.0T1.84
52/1.	[1]	146420-5700	SHIM D9.5&3.0T1.86
52/1.	[1]	146420-5800	SHIM D9.5&3.0T1.88
54.	[4]	146433-0100	GASKET D12&6.4T1.00
55.	[4]	146430-3220	DELIVERY-VALVE ASSEMBLY
56.	[4]	146432-0000	COMPRESSION SPRING
58.	[4]	146440-0220	FITTING
60.	[3]	139106-0100	FLAT-HEAD SCREW
66.	[1]	146600-0100	O-RING
67.	[1]	146504-0520	GOVERNOR COVER
67/1.	[1]	146805-5920	GOVERNOR COVER
67/13.	[1]	146621-3100	UNION NUT
67/14.	[1]	146621-1700	UNION NUT
67/15.	[1]	146526-6400	BLEEDER SCREW
67/16.	[1]	146526-2800	BLEEDER SCREW
67/78.	[1]	146600-4400	SEAL RING
67/91.	[1]	146929-0400	BRACKET
67/92.	[1]	139006-4500	BLEEDER SCREW
67/200.	[1]	139308-0300	PLAIN WASHER
67/201.	[1]	146545-3400	THREADED PIN L53.00
67/201B.	[1]	146545-3500	THREADED PIN L55.00
67/201C.	[1]	146545-3600	THREADED PIN L57.00
67/202.	[1]	139208-0900	UNION NUT
67/203.	[1]	146600-1200	O-RING
68.	[1]	146514-2520	CONTROL SHAFT
69.	[1]	139310-0200	PLAIN WASHER
72.	[1]	146538-4020	CONTROL LEVER
73.	[1]	014110-6440	LOCKING WASHER
75.	[1]	013020-6040	UNION NUT M6P1H5
82.	[1]	146620-1400	FLAT-HEAD SCREW
83.	[1]	013020-6040	UNION NUT M6P1H5
95.	[1]	146561-9520	FULCRUM LEVER
104.	[2]	146568-0000	SLOTTED SPRING PIN
105.	[2]	026508-1140	GASKET D11.4&8.2T1
106.	[2]	146588-0500	COILED SPRING
107.	[1]	146569-0300	UNION NUT
108.	[1]	146570-0100	GOVERNOR SHAFT
109.	[1]	146600-0400	O-RING
110/1.	[1]	146571-0000	SHIM D20.2&8.3T1.05
110/1.	[1]	146571-0100	SHIM D20.2&8.3T1.25
110/1.	[1]	146571-0200	SHIM D20.2&8.3T1.45
110/1.	[1]	146571-0300	SHIM D20.2&8.3T1.65
110/1.	[1]	146571-0400	SHIM D20.2&8.3T1.85
110/1.	[1]	146571-0500	SHIM D20.2&8.3T1.15
110/1.	[1]	146571-0600	SHIM D20.2&8.3T1.35
110/1.	[1]	146571-0700	SHIM D20.2&8.3T1.55
110/1.	[1]	146571-0800	SHIM D20.2&8.3T1.75
111.	[1]	146602-0600	PLAIN WASHER D20&8.4T1.40
112.	[1]	146572-0020	FLYWEIGHT ASSEMBLY
114.	[1]	146602-0500	PLAIN WASHER D17&6.4T1.60
115.	[1]	146575-2000	SLIDING SLEEVE
116.	[1]	146576-0200	CAP
117/1.	[1]	146577-1800	PLUG L2.10
117/1.	[1]	146577-1900	PLUG L2.30
117/1.	[1]	146577-2000	PLUG L2.50
117/1.	[1]	146577-2100	PLUG L2.70
117/1.	[1]	146577-2200	PLUG L2.90
117/1.	[1]	146577-2300	PLUG L3.10
117/1.	[1]	146577-2400	PLUG L3.30
117/1.	[1]	146577-2500	PLUG L3.50
117/1.	[1]	146577-2600	PLUG L3.70
117/1.	[1]	146577-2700	PLUG L3.90
117/1.	[1]	146577-2800	PLUG L4.10
117/1.	[1]	146577-2900	PLUG L4.30
117/1.	[1]	146577-3000	PLUG L4.50
117/1.	[1]	146577-3100	PLUG L4.70
117/1.	[1]	146577-3200	PLUG L4.90
117/1.	[1]	146577-3300	PLUG L5.10
117/1.	[1]	146577-6700	PLUG L2.2
117/1.	[1]	146577-6800	PLUG L2.4
117/1.	[1]	146577-6900	PLUG L2.6
117/1.	[1]	146577-7000	PLUG L2.8
117/1.	[1]	146577-7100	PLUG L3.0
117/1.	[1]	146577-7200	PLUG L3.2
117/1.	[1]	146577-7300	PLUG L3.4
117/1.	[1]	146577-7400	PLUG L3.6
117/1.	[1]	146577-7500	PLUG L3.8
117/1.	[1]	146577-7600	PLUG L4.0
117/1.	[1]	146577-7700	PLUG L4.2
117/1.	[1]	146577-7800	PLUG L4.4
117/1.	[1]	146577-7900	PLUG L4.6
117/1.	[1]	146577-8000	PLUG L4.8
117/1.	[1]	146577-8100	PLUG L5.0
117/1.	[1]	146877-0000	PLUG L5.2
117/1.	[1]	146877-0100	PLUG L5.3
117/1.	[1]	146877-0200	PLUG L5.4
117/1.	[1]	146877-0300	PLUG L5.5
117/1.	[1]	146877-4700	PLUG
117/1.	[1]	146877-4800	PLUG
117/1.	[1]	146877-4900	PLUG
117/1.	[1]	146877-5000	PLUG
123.	[4]	139106-0200	FLAT-HEAD SCREW
130.	[1]	146421-0020	CAPSULE
130/2.	[1]	026508-1140	GASKET D11.4&8.2T1
130/3.	[1]	146422-0000	BLEEDER SCREW
130/4.	[1]	146600-0500	O-RING
133.	[1]	146600-0600	O-RING
134.	[1]	146600-0700	O-RING
135.	[1]	146110-0220	CONTROL VALVE
135/5.	[1]	146114-0000	SPRING WASHER
136.	[1]	146120-0220	OVER FLOW VALVE
137.	[2]	139512-0200	GASKET D18.5&12.2T1.00
138.	[1]	146665-0220	INLET UNION
200.	[1]	146206-0100	COILED SPRING
214.	[1]	146542-5000	BUSHING
216.	[1]	146542-5100	BUSHING
217.	[1]	146541-2900	SLOTTED WASHER
218.	[1]	146592-2100	COILED SPRING
219.	[1]	146541-3000	BUSHING
220.	[1]	146592-3600	COILED SPRING
221.	[1]	146929-8320	BRACKET
222.	[2]	139006-4600	BLEEDER SCREW
230.	[1]	146929-5420	BRACKET
231.	[1]	139006-4600	BLEEDER SCREW
236.	[1]	139006-4800	BLEEDER SCREW
237.	[1]	146620-0200	HEX-SOCKET-HEAD CAP SCREW
240.	[1]	146650-0720	PULLING ELECTROMAGNET
240/8.	[1]	146600-1700	O-RING
243.	[1]	146621-1000	UNION NUT
245.	[3]	139512-0200	GASKET D18.5&12.2T1.00
246.	[1]	139812-0500	EYE BOLT
247.	[1]	146665-3220	INLET UNION
248.	[1]	146614-0200	SPACER BUSHING
275.	[1]	146612-2120	BRACKET
276.	[2]	010010-1640	BLEEDER SCREW M10P1.5L16 4T
280.	[1]	146360-9420	START ADVANCE ASSY
281.	[1]	146600-0800	O-RING
282.	[2]	010206-1240	HEX-SOCKET-HEAD CAP SCREW M6P1L12
287.	[1]	020146-1440	BLEEDER SCREW M6P1L14
309.	[6]	020146-1270	BLEEDER SCREW
309.	[6]	020146-1270	BLEEDER SCREW
309.	[6]	020146-1270	BLEEDER SCREW
309.	[6]	020146-1270	BLEEDER SCREW
310.	[1]	146684-7720	POTENTCIOMETER
310/2.	[1]	146933-2400	BRACKET
310/3.	[2]	139104-0400	FLAT-HEAD SCREW
310/4.	[1]	146648-9200	JOINT CONNECTION
310/4B.	[1]	146648-9300	JOINT CONNECTION
310/4C.	[1]	146648-9400	JOINT CONNECTION
310/4D.	[1]	146648-9500	JOINT CONNECTION
310/4E.	[1]	146648-9600	JOINT CONNECTION
310/4F.	[1]	146648-9700	JOINT CONNECTION
310/4G.	[1]	146648-9800	JOINT CONNECTION
310/4H.	[1]	146648-9900	JOINT CONNECTION
310/4I.	[1]	146649-0000	JOINT CONNECTION
310/4J.	[1]	146649-0100	JOINT CONNECTION
310/4K.	[1]	146649-0200	JOINT CONNECTION
310/4L.	[1]	146649-0300	JOINT CONNECTION
311.	[2]	146620-7300	BLEEDER SCREW
316.	[1]	146680-4520	DAMPER
318.	[1]	146933-5700	BRACKET
319.	[1]	010206-1040	HEX-SOCKET-HEAD CAP SCREW
329.	[1]	146541-4900	PLAIN WASHER D20&10T0.5
800S.	[1]	146009-3920	PUMP HOUSING
800S/1/6.	[1]	146601-0900	PACKING RING
804S.	[1]	146232-0720	COMPRESSION SPRING
805S.	[1]	146574-0120	PARTS SET
810S.	[1]	146600-1120	REPAIR SET
821S.	[1]	146210-5720	ROLLER SET
835S.	[1]	146598-1000	CAP
836S/1.	[1]	146598-0600	CAP L18
836S/1.	[1]	146598-0700	CAP L21
836S/1.	[1]	146598-0800	CAP L24
836S/1.	[1]	146598-0900	CAP L27
847S.	[1]	146683-6710	POTENTCIOMETER
903.	[1]	146672-6120	PULSE GENERATOR
903/2.	[1]	146600-1300	O-RING &13W1.9
906.	[1]	146980-6900	NAMEPLATE

Include in #2:

104740-2950 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 460 611 416 9460611416

ZEXEL 104740-2950 1047402950

Zexel num

Bosch num

Firm num

Name

104740-2950
104740-2951

9 460 611 416

INJECTION-PUMP ASSEMBLY
* K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113orSAEJ967d

Test oil temperature degC 45 45 50

Nozzle 105780-0060

Bosch type code NP-DN0SD1510

Nozzle holder 105780-2150

Opening pressure MPa 13 13 13.3

Opening pressure kgf/cm2 133 133 136

Injection pipe 157805-7320

Injection pipe
Inside diameter - outside diameter - length (mm) mm 2-6-450

Joint assembly 157641-4720

Tube assembly 157641-4020

Transfer pump pressure kPa 20 20 20

Transfer pump pressure kgf/cm2 0.2 0.2 0.2

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Pump speed r/min 1400 1400 1400

Average injection quantity mm3/st. 35.3 34.9 35.7

Difference in delivery mm3/st. 3

Basic *

Oil temperature degC 50 48 52

Injection timing adjustment_02

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 31.1 28.6 33.6

Oil temperature degC 50 48 52

Injection timing adjustment_03

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 30.6 27.6 33.6

Oil temperature degC 50 48 52

Injection timing adjustment_04

Pump speed r/min 1400 1400 1400

Average injection quantity mm3/st. 35.3 34.3 36.3

Difference in delivery mm3/st. 3.5

Basic *

Oil temperature degC 50 48 52

Injection timing adjustment_05

Pump speed r/min 1800 1800 1800

Average injection quantity mm3/st. 35.4 32.9 37.9

Oil temperature degC 50 48 52

Injection timing adjustment_06

Pump speed r/min 2400 2400 2400

Average injection quantity mm3/st. 34.5 31 38

Oil temperature degC 52 50 54

Injection quantity adjustment

Pump speed r/min 2700 2700 2700

Average injection quantity mm3/st. 14 12 16

Difference in delivery mm3/st. 4.5

Basic *

Oil temperature degC 55 52 58

Injection quantity adjustment_02

Pump speed r/min 2700 2700 2700

Average injection quantity mm3/st. 14 10.5 17.5

Difference in delivery mm3/st. 5

Basic *

Oil temperature degC 55 52 58

Injection quantity adjustment_03

Pump speed r/min 2800 2800 2800

Average injection quantity mm3/st. 5

Oil temperature degC 55 52 58

Governor adjustment

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 10.5 9.5 11.5

Difference in delivery mm3/st. 2

Basic *

Oil temperature degC 48 46 50

Governor adjustment_02

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 10.5 8.5 12.5

Difference in delivery mm3/st. 2.5

Basic *

Oil temperature degC 48 46 50

Governor adjustment_03

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 5

Oil temperature degC 50 48 52

Boost compensator adjustment

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 15.1 8.6 21.6

Oil temperature degC 50 48 52

Lever angle (shim thickness) mm 8.9 8.85 8.95

Boost compensator adjustment_02

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 10.3 3.3 17.3

Oil temperature degC 50 48 52

Lever angle (shim thickness) mm 8.9 8.85 8.95

Timer adjustment

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 60 50 70

Oil temperature degC 48 46 50

Remarks
Full

Timer adjustment_02

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 60 50 70

Oil temperature degC 48 46 50

Remarks
Full

Speed control lever angle

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 0 0 0

Oil temperature degC 48 46 50

Remarks
Magnet OFF at idling position

0000000901

Pump speed r/min 1000 1000 1000

Overflow quantity cm3/min 370 240 500

Oil temperature degC 50 48 52

Stop lever angle

Pump speed r/min 1000 1000 1000

Pressure kPa 353 333 373

Pressure kgf/cm2 3.6 3.4 3.8

Basic *

Oil temperature degC 50 48 52

Stop lever angle_02

Pump speed r/min 1000 1000 1000

Pressure kPa 373 334 412

Pressure kgf/cm2 3.8 3.4 4.2

Basic *

Oil temperature degC 50 48 52

Stop lever angle_03

Pump speed r/min 1800 1800 1800

Pressure kPa 520 471 569

Pressure kgf/cm2 5.3 4.8 5.8

Oil temperature degC 50 48 52

Stop lever angle_04

Pump speed r/min 2400 2400 2400

Pressure kPa 637 588 686

Pressure kgf/cm2 6.5 6 7

Oil temperature degC 52 50 54

0000001101

Pump speed r/min 1000 1000 1000

Timer stroke mm 1.9 1.7 2.1

Basic *

Oil temperature degC 50 48 52

_02

Pump speed r/min 1000 1000 1000

Timer stroke mm 1.9 1.6 2.2

Basic *

Oil temperature degC 50 48 52

_03

Pump speed r/min 1800 1800 1800

Timer stroke mm 5.6 5.1 6.1

Oil temperature degC 50 48 52

_04

Pump speed r/min 2400 2400 2400

Timer stroke mm 7.4 6.9 7.8

Oil temperature degC 52 50 54

0000001201

Max. applied voltage V 8 8 8

Test voltage V 13 12 14

Timing setting

K dimension mm 3.3 3.2 3.4

KF dimension mm 6.78 6.68 6.88

MS dimension mm 0.8 0.7 0.9

Control lever angle alpha deg. 25 23 27

Control lever angle beta deg. 44 39 49

Test data Ex:

0000001801 POTENTIOMETER ADJUSTMENT

Adjustment of the potentiometer In the following condition, change the installation position of the potentiometer to adjust the output voltage to within the specified values. Measure the injection quantity at control lever position a (shim thickness = approximately L mm) at N = N1 r/min, determine the voltage using the formula, and adjust the potentiometer. A:Adjustment conditions B:Adjustment value C:Position of the control lever N:Pump speed Q:Injection quantity Vo:Output voltage D:Measured injection quantity E:Conversion formula F:Adjusting point G:Idle H:Full speed I:Checking point K:Applied voltage X:Injection quantity (cm3/1,000st) Y:Voltage (V) M:Connecting diagram for the potentiometer O:Output P:Output when (2) and (3) connected. R:At target value Q1cm3/1,000 st, set voltage at V3 (V).
----------
N1=700r/min a=13.9deg L=8.9+-0.05mm Q1=15.1cm3/1,000st V3=4.46V
----------
Q1=15.1cm3/1.000st V1=(1.7--)V V2=9.96++V V3=4.46V J=V+-0.03=0.13121X+2.4787

0000001901 W-CSD ADJUSTMENT

Adjustment of the W-CSD 1. Adjustment of the advance angle of the timer (1)Determine the timer advance angle from the graph in Fig. 3 (Q). (2)(1) Adjust using the screw (I) so that the timer advance angle determined in item (1) is obtained. 2. Setting the intermediate lever position (refer to fig 1 and fig 2) (1)Insert a block gauge L1 between the idling set screw (H) and the control lever (G). (2)Insert a shim of thickness L2 mm between the intermediate lever (D) and the intermediate lever bracket (E). Ensure the screw (F) contacts the control lever (G), then fix the nut. 3. W-CSD lever adjustment [refer to fig 1 (O) and fig 2 (P)] (1)After completing (2) above, remove the block gauge L3 and the shim with the thickness L4. (2)Insert a block gauge L5 determined from the graph (L-t) in figure 3 (Q) between the idling set screw (H) and the control lever (G). (3)Adjust the screw (B) until the screw (F) contacts the control lever (G). Then fix locknut (A). Caution: The temperature of the wax at adjustment must not exceed a. X:Temperature t (deg C) Y1:Timer lift TA (mm) Y2:Control lever L dimension (mm; control lever position) J:Graph TA-t: t (deg C) <= 10: TA = 0.82 10 <= t (deg C) <= 20: TA =-0.027t + 1.09 20 <= t (deg C) <= 40: TA = -0.0275t + 1.1 K:Graph L-t t (deg C) <= 10: L = 3.9 10 <= t (deg C) <= 30: L =-0.09t + 4.8 20 <= t (deg C) <= 54.3: L = -0.086t + 4.68
----------
a=30degC L1=3.0+-0.05mm L2=5.3+-0.05mm L3=3mm L4=5.3mm L5=L+-0.05mm
----------
L1=3.0+-0.05mm L2=5.3+-0.05mm

0000002001 DASHPOT ADJUSTMENT

Adjustment of the dash pot 1. Insert a block gauge L (thickness gauge) between the idle set screw (C) and the control lever (D). 2. In the above condition, adjust the position of the dash pot so that the dash pot adjustment screw (A) contacts the push rod and then fix the screw using the nut (B). T3T3 Note: (1)The adjusting screw and pushrod contact faces must be smooth. (2)Confirm that the control lever returns to the idling position. (E): 6 locations
----------
T3=5~7Nm{0.5~0.7kgfm} L=6.0+-0.05mm
----------
T1=15~20Nm{1.5~2.0kgfm} T2=6~9Nm{0.6~0.9kgfm} SW1=SW22mm SW2=SW10mm L=6.0+-0.05mm

Information:

Flush
8. Refill the cooling system with clean water mixed with the proper concentration (six to ten percent) of Fast Acting-Type Caterpillar Cooling System Cleaner. Tighten cooling system vent cap. For proper cooling system maintenance cleaning, refer to label directions for the type of Caterpillar Cooling System Cleaner used in your cooling system.9. Start and run (operate) the engine to circulate fluid in the cooling system.10. Stop the engine and allow to cool. Loosen cooling system vent cap and drain plugs.11. Drain the cleaning solution. Flush the cooling system with clean water and a neutralizing solution until draining water is clear. Clean and install all drain plugs and/or close the drain valve. Sodium Carbonate crystals at a rate of 250 grams per 40 liters of water (1/2 pound per 10 U.S. gallon of water) may be used as a neutralizer. Repeat Steps 8 thru 11 if necessary until the draining water is clear.Install Thermostat
Caterpillar engines incorporate a shunt design cooling system and require operating the engine with a thermostat installed.If the thermostat is installed wrong, it will cause the engine to overheat.
Inspect gaskets before assembly and replace if worn or damaged.12. Install a new seal in the thermostat housing and install a new thermostat.13. Install a new gasket and the thermostat housing on the engine cylinder head.14. Install the cooling system connections and tighten the hose or piping clamps.Fill
All water is corrosive at engine operating temperature. The cooling system should be protected with cooling system conditioner at all times. Use Caterpillar liquid cooling system conditioner to treat the coolant mixture.
Refer to the Cooling System Specifications section of this publication for all information regarding about the appropriate maintenance of the cooling system or contact your Caterpillar dealer for assistance. See Refill Capacities chart in this publication for the capacity of your engine's system.15. Be certain all drain plugs are clean and installed. Mix a solution of acceptable water and Caterpillar Antifreeze (which contains supplemental coolant additive).16. Start and run the engine with the cooling system vent cap loosened. Operate the engine and allow the coolant to warm, the thermostats to open and the coolant level to stabilize. Inspect for leaks and proper operating temperature.
To prevent engine damage, never add coolant to an overheated engine. Allow the engine to cool first.
17. Add coolant mixture if necessary to bring the coolant to within 13 mm (1/2 inch) below the bottom of the fill tube or the correct level on the sight glass, if equipped. Upon initial fill the sight gauge can indicate an incorrect coolant level. Be sure the coolant is to the bottom of the fill tube. Recheck the coolant level and fill the cooling system to the bottom of the fill tube if the system was low.
In cold weather, frequently check the specific gravity of the coolant solution to ensure adequate protection.If the engine is to be stored in, or shipped to an area with freezing temperatures, the cooling system must be either protected to the lowest expected outside temperature