104302-6191 ZEXEL 9 400 616 413 BOSCH INJECTION-PUMP ASSEMBLY 9400616413 1043026191 5156011880


 

Information injection-pump assembly

BOSCH 9 400 616 413 9400616413
ZEXEL 104302-6191 1043026191
ISUZU 5156011880 5156011880
104302-6191 INJECTION-PUMP ASSEMBLY
Rating:
48
Buy INJECTION-PUMP ASSEMBLY 104302-6191 zexel genuine, new aftermarket engine parts with delivery

Service parts 104302-6191 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 104300-0361
3. GOVERNOR
4. SUPPLY PUMP 105248-0110
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2)
13. NOZZLE-HOLDER
14. NOZZLE
15. NOZZLE SET

Include in #1:

104302-6191 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104302-6191 
9 400 616 413 
5156011880  ISUZU
INJECTION-PUMP ASSEMBLY
2AB1 K 14BT INJECTION PUMP ASSY PES2K PE




Information:

start by:a) remove fuel injection lines**This operation location is in the ENGINE DISASSEMBLY AND ASSEMBLY section. 1. Disconnect the fuel lines from fuel transfer pump (4) and fuel manifold (3). Disconnect fuel line (2) from the fitting. Disconnect the fuel return line to the tank at (1). Install plugs or caps on all fuel line openings.2. Disconnect drain line (5) from the governor housing. Move the fuel lines and drain line clear of the fuel injection pump housing and governor. 3. Remove bolts (6) that hold the oil manifold to the governor housing. 4. Remove cover (7) from the timing gear cover.5. Remove the bolt and washer that hold the timing gear to the camshaft in the fuel injection pump housing. 6. Install tooling (A) and loosen the timing gear on the camshaft in the fuel injection pump housing.7. Fasten a strap and hoist to the fuel injection pump housing and governor as shown. 8. Remove three nuts (8) and remove the fuel injection pump housing and governor. Weight is 25 kg (56 lb.).Install Fuel Injection Pump Housing And Governor
1. Be sure O-ring seals (1) and (2) are in position on the fuel injection pump housing and governor and put clean oil on the O-ring seals.2. Remove the cover on the fuel injection pump housing and install timing pin (A). Turn the camshaft until timing pin (A) goes in the groove in the camshaft as shown. 3. Fasten a strap and hoist to the fuel injection pump housing and governor and put in position on the timing gear plate and oil manifold (3). Install the three nuts that hold the fuel injection pump housing to the timing gear plate and the two bolts that hold the governor housing to oil manifold (3).
After the fuel injection pump housing and governor are installed on the timing gear plate be sure the rack is free to move. The O-ring seal on the drive end of the fuel injection pump can hold the rack and prevent free movement of the rack. If the rack does not move freely remove the fuel injection pump housing and governor and check the O-ring seal on the drive end of the fuel injection pump housing.
4. Install the bolt and washer (4) as shown to hold the timing gear to the camshaft. Install washer (4) with the larger outside diameter toward the bolt head. Tighten the bolt finger tight only.5. Use the following procedure to put the No. 1 piston at top center on the compression stroke. No. 1 piston at top center (TC) on the compression stroke is the starting point for all timing procedures. The engine is seen from the flywheel end when direction of flywheel rotation is given. Do not turn the flywheel backward. a) Remove plug (5) from the flywheel housing and the breather from the valve cover.b) Turn the flywheel counterclockwise until a 3/8"-16 NC bolt (6) at least 2.5 in. long can be installed in the flywheel through the hole in

Have questions with 104302-6191?





Group cross 104302-6191 ZEXEL

Isuzu 

9 400 612 461 
5156011750 
INJECTION-PUMP ASSEMBLY
2AA1
9 400 610 292 
5156011760 
INJECTION-PUMP ASSEMBLY
2AA1
 
5156011810 
INJECTION-PUMP ASSEMBLY
2AB1
9 400 610 082 
 
INJECTION-PUMP ASSEMBLY
2AB1

Isuzu 

9 400 610 082 
5156011830 
INJECTION-PUMP ASSEMBLY
2AB1
 
5156011820 
INJECTION-PUMP ASSEMBLY
2AB1
F 019 Z20 487 
5156011850 
INJECTION-PUMP ASSEMBLY
2AB1
9 400 610 121 
5156011840 
INJECTION-PUMP ASSEMBLY
2AB1
 
5156011860 
INJECTION-PUMP ASSEMBLY
2AB1
 
5156011870 
INJECTION-PUMP ASSEMBLY
2AB1
104302-6191  
9 400 616 413 
5156011880 
INJECTION-PUMP ASSEMBLY
2AB1
Back to top