104302-6181 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1043026181 5156011870


 

Information injection-pump assembly

ZEXEL 104302-6181 1043026181
ISUZU 5156011870 5156011870
104302-6181 INJECTION-PUMP ASSEMBLY
Rating:
47
Buy INJECTION-PUMP ASSEMBLY 104302-6181 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
104302-6181 
 
5156011870  ISUZU
INJECTION-PUMP ASSEMBLY
2AB1 * K




Information:

1. Remove the fuel injection lines. It is not necessary to remove the fuel transfer pump, the fuel injection pump housing and governor to remove the fuel injection pumps. 2. Remove cover (1). 3. Move the rack until tool (A) can be installed to hold the rack in the center position. The rack must be in the center position to remove the fuel injection pumps.4. Use tool (B) to remove bushing (2). 5. Install tool (C) on the bonnet and remove the fuel injection pump. 6. Remove spacer (3) from the fuel injection pump housing. Spacers (3) are the same thickness for each fuel injection pump so they can be mixed. The fuel injection pump plungers and barrels are sets and can not be mixed.Install Fuel Injection Pumps
1. Install spacer (1) in the fuel injection pump housing. 2. Move the rack until tool (A) can be installed to hold the rack in the center position. The rack must be in the center position to install the fuel injection pumps.3. Turn the camshaft until the lobe of the camshaft is down for the pump to be installed. 4. Install tool (B) on the bonnet of the fuel injection pump. Put clean oil on O-ring seal (4) and install the O-ring seal and bushing (5) over tool (B) as shown. 5. Install the fuel injection pump in the pump housing with saw cut (slot) (3) in the gear in alignment with small pin (2) in the lifter assembly and groove (7) in the barrel in alignment with large pin (6) in the pump housing.6. Push down on tool (B) and tighten bushing (5) by hand until the bushing is even with the top of the housing. If installation of the bushing can not be made this far by hand, remove it. Remove the pump, put the parts in alignment again and install the bushing again.
If installation of pump is correct, the bushing can be tightened by hand until it is even with the face of the pump housing.
7. Remove tool (B) and install tool (C) in the bushing. Use tool (C) and a torque wrench to tighten the bushing to a torque of 165 14 N m (120 10 lb. ft.).8. Remove tools (C) and (A). Install the cover on the fuel injection pump housing.9. Install the fuel injection lines. Tighten the fuel injection line nuts to a torque of 41 7 N m (30 5 lb.ft.).Disassemble Fuel Injection Pumps
start by:a) remove fuel injection pumps
Be careful when the injection pumps are disassembled. Do not damage the surfaces of the plungers, barrels and bonnets. Any scratches will cause leakage inside the fuel injection pump. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
1. Pull plunger (1)

Have questions with 104302-6181?





Group cross 104302-6181 ZEXEL

Isuzu 

9 400 612 461 
5156011750 
INJECTION-PUMP ASSEMBLY
2AA1
9 400 610 292 
5156011760 
INJECTION-PUMP ASSEMBLY
2AA1
 
5156011810 
INJECTION-PUMP ASSEMBLY
2AB1
9 400 610 082 
 
INJECTION-PUMP ASSEMBLY
2AB1

Isuzu 

9 400 610 082 
5156011830 
INJECTION-PUMP ASSEMBLY
2AB1
 
5156011820 
INJECTION-PUMP ASSEMBLY
2AB1
F 019 Z20 487 
5156011850 
INJECTION-PUMP ASSEMBLY
2AB1
9 400 610 121 
5156011840 
INJECTION-PUMP ASSEMBLY
2AB1
 
5156011860 
INJECTION-PUMP ASSEMBLY
2AB1
104302-6181  
 
5156011870 
INJECTION-PUMP ASSEMBLY
2AB1
9 400 616 413 
5156011880 
INJECTION-PUMP ASSEMBLY
2AB1
Back to top