103682-0320 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1036820320 211090320

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 103682-0320 1036820320

SHINKO-ENGIN. 211090320 211090320

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 103682-0320 zexel genuine, new aftermarket engine parts with delivery

Service parts 103682-0320 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 103068-9310

3. GOVERNOR 105455-0450

4. SUPPLY PUMP 105235-1290

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE 156609-2020

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-2060

11. Nozzle and Holder 100-21914-0

12. Open Pre:MPa(Kqf/cm2) 12.7{130}

13. NOZZLE-HOLDER 105031-3570

14. NOZZLE 105000-1670

15. NOZZLE SET

Include in #1:

103682-0320 as INJECTION-PUMP ASSEMBLY

106971-2091 as _

Cross reference number

ZEXEL 103682-0320 1036820320

SHINKO-ENGIN. 211090320 211090320

Zexel num

Bosch num

Firm num

Name

103682-0320

211090320 SHINKO-ENGIN.

INJECTION-PUMP ASSEMBLY
S618 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle 105000-1470

Bosch type code DN0SD130NP1

Nozzle holder 105031-3280

Opening pressure MPa 12.7

Opening pressure kgf/cm2 130

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-540

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 2.55 2.5 2.6

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 18.5

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 635 610 660

Max. variation between cylinders % 0 -4 4

Fixing the rack *

Injection quantity adjustment_02

Adjusting point B

Rack position 20

Pump speed r/min 550 550 550

Average injection quantity mm3/st. 700 672 728

Max. variation between cylinders % 0 -4 4

Fixing the rack *

Injection quantity adjustment_03

Adjusting point C

Rack position 18

Pump speed r/min 750 750 750

Average injection quantity mm3/st. 600 582 618

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the rack *

Injection quantity adjustment_04

Adjusting point D

Rack position 10+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 81 73 89

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)RACK LIMIT: RAL (3)Idle sub spring setting: L1.
----------
K=23 RAL=21+0.5mm L1=9-0.5mm
----------

Speed control lever angle

M:Maximum speed S:Stop
----------

----------
a=(30deg) b=(40deg)

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=(35deg) b=(10deg)

Information:

Close the gauge protector valve ( 0 to 40,000 kPa (0 to 5,800 psi) gauge).
Visually inspect the pattern of the fuel nozzle for a uniform spray.Note: For this test, each full stroke of the pump should be performed in less than one second.
Rapidly increase the pressure on the fuel nozzle until fluid sprays from the tip of the fuel nozzle.
Test fluid should spray from the tip of the nozzle in a pattern that is uniform. Refer to Illustration 2.
Check the individual spray orifices for partial plugging.
Use a moderate pump stroke to open the valve of the fuel nozzle.
During the pump stroke, view the individual spray orifices for partial plugging.The test fluid should spray uniformly from all the orifices.If an orifice is plugged or the pattern is distorted, clean the fuel nozzle orifices and repeat this test. Refer to Special Instruction, SEHS8627, "Use of 8S-2245 Nozzle Cleaning Tool Group" for instructions on tool usage and cleaning procedures.Test the Fuel Nozzle for Seal Leakage
Note: Testing for seal leakage is not a requirement for the 104-9450 Fuel Nozzle, 104-9452 Fuel Nozzle, 104-9453 Fuel Nozzle, or the 104-9454 Fuel Nozzle. Do not perform this test on these fuel nozzles.
Illustration 3 g00453789
Typical example of a 7000 Series fuel nozzle
Remove the cloth from the top of the nozzle.
Prior to performing this test, install a new seal washer on purging screw (A) and reinstall the purging screw into the fuel nozzle.
Illustration 4 g00453809
Tighten purging screw (D) or purging screw (E) to a torque of 2.2 0.8 N m (20 7 lb in). Note: Use a 6V-4980 Torque Screwdriver Tool Group to torque the purging screw.
Apply a test pressure of 13,800 kPa (2,000 psi) to the fuel nozzle.Note: Due to the large amount of test fluid that is delivered to the fuel nozzle, hydraulic lock may prevent the nozzle from opening during this test. If a hydraulic lock occurs, slowly loosen the adapter fitting to relieve the pressure on the fuel nozzle valve assembly.If there is leakage at the purging screw, install a new 8C-3234 Screw and a 114-3364 Washer as replacement parts. Retest the fuel nozzle for leaks.Do not use the nozzle if there is leakage that cannot be repaired at purging screw (A), upper seal joint (B), or lower seal joint (C).Returning Fuel Nozzles to Service
Illustration 5 g00453817Prior to returning fuel nozzles to service, install a new seal washer (3) and install a new carbon dam (4) on the fuel nozzle (1).Use 6V-4979 Carbon Seal Installation Tool (2) to install a new carbon dam (4).Table 5 contains part numbers for the replacement of the fuel nozzle seal washers.
Table 5
Seal Washers
Fuel Nozzle Washer (Color) Washer Thickness
8N-7004 4W-3914 (Gray) 1.27 mm (0.050 inch)
4W-7012
4W-7013
4W-7014
4W-7015 4W-6060 (Blue) 3.18 mm (0.125 inch)
4W-7018
4W-7019
4W-7020
4W-7021
4W-7022
7W-7045
100-7552
100-7562
100-7563
104-3377
167-7489
170-5181
170-5183 7W-4482 (Green) 3.18 mm (0.125 inch)
133-3896 7W-4483 (Red) 2.54 mm (0.100 inch)
4W-7011
4W-7016
7W-7024 7W-4485 (Copper) 1.27 mm (0.050 inch)
8N-7003
7W-7038
8N-7005
100-7559
100-7561
100-7564
104-9450
104-9452
104-9453
104-9454
131-3190
154-3198
170-5187 7W-4486 (Violet) 1.84 mm (0.072 inch)
4W-7017
7W-7026
7W-7030
7W-7031
7W-7032
7W-7033
7W-7035
7W-7037
7W-7040
7W-7041
7W-7042
7W-7043
7W-7044
8N-7007
100-7550
100-7551
100-7556
100-7557
100-7558
100-7560
100-7565
100-7567
100-7600
121-4353
127-9792
127-9793
129-1351
130-1804
130-1806
130-5187
130-5190
131-0811
131-0812
131-1242
131-1243
131-7937
134-0944
171-4093 7W-4487 (Black) 1.27 mm (0.050 inch)
7W-7023