101701-9500 ZEXEL 9 400 616 196 BOSCH INJECTION-PUMP ASSEMBLY 9400616196 1017019500 16714z5677

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 616 196 9400616196

ZEXEL 101701-9500 1017019500

NISSAN-DIESEL 16714Z5677 16714z5677

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101701-9500 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

106871-2670 as _

Cross reference number

BOSCH 9 400 616 196 9400616196

ZEXEL 101701-9500 1017019500

NISSAN-DIESEL 16714Z5677 16714z5677

Zexel num

Bosch num

Firm num

Name

101701-9500

9 400 616 196

16714Z5677 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
FE6A K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8310

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2240

Opening pressure MPa 18

Opening pressure kgf/cm2 184

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-8120

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.5 3.47 3.53

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point -

Rack position 12.8

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 59.5 57.5 61.5

Max. variation between cylinders % 0 -3.5 3.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 9.8+-0.5

Pump speed r/min 265 265 265

Average injection quantity mm3/st. 13 11.2 14.8

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.8)

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 59.5 58.5 60.5

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+1.75

Pump speed r/min 1400 1400 1400

Average injection quantity mm3/st. 63.5 59.5 67.5

Fixing the lever *

Timer adjustment

Pump speed r/min 1270

Advance angle deg. 3 2.5 3.5

Load 3/4

Timer adjustment_02

Pump speed r/min 1470

Advance angle deg. 6 5.7 6.3

Load 4/4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm.
----------
T1=P20
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=100mm
----------
a=22deg+-5deg b=(46.5deg)+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=42mm
----------
a=25deg+-5deg b=40deg+-5deg

0000001501 RACK SENSOR

G:Red paint H:Pump end face P/N: part number of suitable shim (1)Threaded type rack block (2)Welded type rack block Rack sensor adjustment 1. Threaded type rack sensor (-5*20, P type, no TICS rack limit). (1)Screw in the bobbin (A) until it contacts the joint (B). (2)Fix the pump lever. (3)At speed N1 and rack position Ra, adjust the amount that the bobbin is screwed in so that the amp's output voltage is V1. (4)Fix using the nut (F). (5)Affix the caution plate to the upper part of the joint (B). (6)Apply (G) at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the end surface of the pump (H) and the joint (B) 2. Range for screw-in adjustment between the bobbin (A) and the joint (B) is 9 threads. Screw in to the end from (the position where the bobbin (A) is rotated 9 turns). Speed N1, rack position Ra, output voltage V1, rack sensor supply voltage 5+-0.01 (V)
----------
Ra=R1(12.8)mm N1=600r/min V1=2.6+-0.01V
----------

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(20deg)

Information:

Refer to Table 2 and find the engine current static timing ("deg BTC") with the corresponding timing dimension ("dim mm"). Because the current timing must be retarded by 2.5 degrees, subtract 2.5 from the current "deg BTC" and locate that value under the same heading. Refer to the corresponding "dim mm" for the correct timing dimension.An example is an engine that currently has a static timing of 20.0 degrees BTC and a 116.65 mm timing dimension. These values are listed under the heading of "High Speed High Overlap". The result of 20.0 minus 2.5 is 17.5. The 17.5 degrees BTC has a corresponding 117.62 mm timing dimension for the injector.Label the Engine for the New Timing Dimension
Illustration 8 g00977473
Typical engine Information PlateAfter the timing has been adjusted, alter the engine Information Plate. The Information Plate is glued between the two side covers at the rear of the engine on the right side of the cylinder block.You can carefully grind off the original timing dimension. Then etch the new timing dimension onto the plate. Otherwise, permanently remove the original timing dimension by grinding or by marking. Then, obtain a 236-1777 Instruction Plate (Fuel Injector Timing).
Illustration 9 g00988962
236-1777 Instruction Plate (Fuel Injector Timing) Stamp the new timing dimension and the part number of the fuel injector onto the instruction plate. The plate has an adhesive backing. Press the plate onto the engine below the engine original Information Plate.Additional Instructions and Assistance
For the procedure to set the fuel injector timing dimension, refer to the engine's Systems Operation/Testing and Adjusting, "Fuel Setting".