101696-9960 ZEXEL 9 400 616 164 BOSCH INJECTION-PUMP ASSEMBLY 9400616164 1016969960 16713z6817

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 616 164 9400616164

ZEXEL 101696-9960 1016969960

NISSAN-DIESEL 16713Z6817 16713z6817

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101696-9960 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

101803-1760 as _

Cross reference number

BOSCH 9 400 616 164 9400616164

ZEXEL 101696-9960 1016969960

NISSAN-DIESEL 16713Z6817 16713z6817

Zexel num

Bosch num

Firm num

Name

101696-9960

9 400 616 164

16713Z6817 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
FE6T K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-1520

Overflow valve opening pressure kPa 162 147 177

Overflow valve opening pressure kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.9 3.85 3.95

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 12.7

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 83 81 85

Max. variation between cylinders % 0 -3.5 3.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 9.5+-0.5

Pump speed r/min 275 275 275

Average injection quantity mm3/st. 9.6 7.8 11.4

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.7)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 83 82 84

Basic *

Fixing the lever *

Boost pressure kPa 21.3 21.3

Boost pressure mmHg 160 160

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.05

Pump speed r/min 1400 1400 1400

Average injection quantity mm3/st. 93.5 90.3 96.7

Fixing the lever *

Boost pressure kPa 21.3 21.3

Boost pressure mmHg 160 160

Injection quantity adjustment_05

Adjusting point C

Rack position R2[R1-0. 1]

Pump speed r/min 550 550 550

Average injection quantity mm3/st. 77.5 74.3 80.7

Fixing the lever *

Boost pressure kPa 21.3 21.3

Boost pressure mmHg 160 160

Injection quantity adjustment_06

Adjusting point D

Rack position R2-0.5

Pump speed r/min 550 550 550

Average injection quantity mm3/st. 66.5 64.5 68.5

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Injection quantity adjustment_07

Adjusting point I

Rack position -

Pump speed r/min 150 150 150

Average injection quantity mm3/st. 84 84 104

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Rack limit *

Boost compensator adjustment

Pump speed r/min 550 550 550

Rack position R2-0.5

Boost pressure kPa 4 2.7 5.3

Boost pressure mmHg 30 20 40

Boost compensator adjustment_02

Pump speed r/min 550 550 550

Rack position R2[R1-0. 1]

Boost pressure kPa 8 8 8

Boost pressure mmHg 60 60 60

Timer adjustment

Pump speed r/min 1170--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1120

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1400

Advance angle deg. 3 2.5 3.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Boost compensator stroke: BCL
----------
T1=F07 BCL=0.5+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=36mm
----------
a=26.5deg+-5deg b=44deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=20deg+-5deg b=40deg+-5deg

0000001501 TAMPER PROOF

1. Method for setting tamperproof proofing (1)After governor adjustment (torque cam phase adjustment), move the load lever to increase the full rack position to Ra. (2)At pump speed N1, push in the screw (A) until the rack position is Rb. (3)Temporarily caulk using the tip of a screwdriver (4)Confirm that the rack at that time is at Rc. (5)Lock using setscrew (B). (Tightening torque = T) (6)Next, coat (C) with adhesive and then pressfit. (7)Then, readjust the full rack position using the load lever.
----------
N1=1400r/min Ra=(1)mm Rb=R1(12.7)+0.25mm Rc=R1(12.7)+0.25mm
----------
T=4.9~7N-m(0.5~0.7Kgf-m)

Timing setting

(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(60deg)

Information:

Test Procedure
System Operation
The SLC 5/04 diagnostic indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: Input devices, Output devices, Wiring and The controller.The green "RUN" LED is illuminated. The processor is in the "RUN" mode.The red "FLT" LED is flashing during operation. The processor detects a major fault. The fault is in the processor expansion chassis or the fault is in the memory.The amber "FORCE" LED is illuminated. The forces are enabled.The amber "FORCE" LED is not illuminated. No forces are present or no forces are enabled.
Illustration 1 g00563544
Diagram of the LED indicators
Illustration 2 g00562937
Functional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Clear the fault.
Place the switch in the PROG position.
Place the switch in the RUN position.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Proceed to 3.
Cycle the power.
Secure power to the PLC.
Energize the PLC.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Refer to Maintenance Procedure, "Processor - Replace".