101608-6214 ZEXEL F 019 Z20 015 BOSCH INJECTION-PUMP ASSEMBLY f019z20015 1016086214 me078795

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH F 019 Z20 015 f019z20015

ZEXEL 101608-6214 1016086214

MITSUBISHI ME078795 me078795

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101608-6214 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104749-0571 as _

Cross reference number

BOSCH F 019 Z20 015 f019z20015

ZEXEL 101608-6214 1016086214

MITSUBISHI ME078795 me078795

Zexel num

Bosch num

Firm num

Name

101608-6214

F 019 Z20 015

ME078795 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D16TLEC K 14BN INJECTION PUMP ASSY PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-5520

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.5 4.45 4.55

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 10.6

Pump speed r/min 1050 1050 1050

Average injection quantity mm3/st. 108 107 109

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Boost pressure kPa 50.7 50.7

Boost pressure mmHg 380 380

Injection quantity adjustment_02

Adjusting point C

Rack position 7.6+-0.5

Pump speed r/min 425 425 425

Average injection quantity mm3/st. 9.5 8 11

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Injection quantity adjustment_03

Adjusting point E

Rack position 11.4++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 120 110 130

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Rack limit *

Boost compensator adjustment

Pump speed r/min 700 700 700

Rack position R1-0.7

Boost pressure kPa 22.7 20 25.4

Boost pressure mmHg 170 150 190

Boost compensator adjustment_02

Pump speed r/min 700 700 700

Rack position R1(10.6)

Boost pressure kPa 37.3 30.6 44

Boost pressure mmHg 280 230 330

Timer adjustment

Pump speed r/min 1100++

Advance angle deg. 0 0 0

Remarks
Do not advance until starting N = 1100.

Timer adjustment_02

Pump speed r/min -

Advance angle deg. 4 4 4

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Notch fixed: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Boost compensator stroke: BCL (7)At delivery
----------
K=10 BCL=0.7+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle S:Stop (1)Set the pump speed at aa (2)Stopper bolt setting
----------
aa=1190r/min
----------
a=(20deg)+-5deg b=(5deg)+-5deg c=35deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Normal (2)Pump speed aa and rack position bb (to be sealed at delivery)
----------
aa=0r/min bb=4-0.5mm
----------
a=28deg+-5deg b=(48deg)

0000001501 TAMPER PROOF

Tamperproofing-equipped boost compensator cover installation procedure (A) After adjusting the boost compensator, tighten the bolts to remove the heads. (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=14deg
----------
a=(7deg)

Information:

REM07-15
Reman
July 2007APPEARANCE CHANGE TO REMAN ELECTRONIC INJECTORS EI400, EI550 CLASSIC, BRIDGE, EI800 AND INJECTORS WITH ACERT? TECHNOLOGY EI500 AND EI550
Announcement
The Caterpillar Remanufactured Products Group announces an appearance change on selected Cat Reman electronic injectors EI400, EI550 Classic, Bridge, EI800 and injectors with ACERT? technology EI500 and EI550 effective 01/26/07. In order to improve the salvage of injectors? components, Cat Reman is introducing the reuse of solenoid with steel ring around the stator on the above mentioned electronic unit injectors.
Therefore, this will change the appearance of the injectors having stators with the steel ring around the solenoid and without it. However, this change will not alter fit or performance in any way. Please refer to the pictures and table below for more detail.
Part Numbers Impacted
The table below lists part numbers impacted by this appearance change.
Features And Benefits
Cat? Remanufactured Engine Components offer excellent value to customers. Customers who want fast repair turn-around, superior quality and reliability, and lower repair costs will benefit from the use of these Remanufactured Engine Components. Cat Remanufactured Engine Components provide immediate, off-the-shelf availability at a fraction of the new price.
Core Acceptance
Core Acceptance Criteria for Caterpillar Remanufactured Engine Components is simple, visual, and requires no special tools. Consult your Core Acceptance Guide for complete details.
Warranty
Please consult the appropriate warranty statement for your area.
Core Management
Please refer to the Caterpillar Core Management Information System (CMIS 2) Parts Information application describing all reman part/CAF and related information. Also refer to other CMIS 2 inquiry applications such as Customer Profiles, Inspection Reason Codes, Inspection Line Inquiry, Add Charge Information, Entitlement Activity, Entitlement Inquiry, CCR Inquiry, CCR Entry, Shipment Processing; Process Packaging Grief; and Reporting to properly manage core returns and monitor inspection performance. This information will be available to all dealers worldwide after your CMIS 2 conversion date. In the meantime, please continue to use the current CMIS Entitlement Parts Inquiry Screen describing the list of parts in a Core Acceptability Family (CAF) and related part number detail.
For the latest updates of Reman Policies and Core Management (SELD0122), Core Management Systems & Operations Procedures (SELD0040), and Shipping Instructions (SELD0039), go to the Reman Dealer website https://reman.cat.com
If you have any questions regarding core return processing, feel free to call Corinth toll free at (800) 537-2928. For assistance with technical questions, call the Peoria Reman Technical Help Line also toll free at (888) 88-REMAN or use our E-mail address--Reman_Help.
PELJ0791 CATERPILLAR? ?2007 Caterpillar