101607-6500 ZEXEL 9 400 615 707 BOSCH INJECTION-PUMP ASSEMBLY 9400615707 1016076500 me075590

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 615 707 9400615707

ZEXEL 101607-6500 1016076500

MITSUBISHI ME075590 me075590

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101607-6500 zexel genuine, new aftermarket engine parts with delivery

Service parts 101607-6500 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101061-8471

3. GOVERNOR 105931-9640

4. SUPPLY PUMP 105210-6020

5. AUTOM. ADVANCE MECHANIS 105643-0940

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105110-7053

11. Nozzle and Holder ME076953

12. Open Pre:MPa(Kqf/cm2) 15.7{160}/21.6{220}

13. NOZZLE-HOLDER 105041-3031

14. NOZZLE

15. NOZZLE SET 105019-0220

Include in #1:

101402-7662 as _

101607-6500 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 615 707 9400615707

ZEXEL 101607-6500 1016076500

MITSUBISHI ME075590 me075590

Zexel num

Bosch num

Firm num

Name

101607-6500

9 400 615 707

ME075590 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D15T3 K 14BF INJECTION PUMP ASSY PE6AD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-8420

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.2 3.15 3.25

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 12.3

Pump speed r/min 700 700 700

Each cylinder's injection qty mm3/st. 101.8 98.7 104.9

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 9.5+-0.5

Pump speed r/min 600 600 600

Each cylinder's injection qty mm3/st. 11.5 9.8 13.2

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.3)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 101.8 100.8 102.8

Basic *

Fixing the lever *

Boost pressure kPa 36 36

Boost pressure mmHg 270 270

Injection quantity adjustment_04

Adjusting point B

Rack position R1+1

Pump speed r/min 1350 1350 1350

Average injection quantity mm3/st. 117.9 113.9 121.9

Fixing the lever *

Boost pressure kPa 36 36

Boost pressure mmHg 270 270

Injection quantity adjustment_05

Adjusting point C

Rack position R2[R1-0. 4]

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 92.6 88.6 96.6

Fixing the lever *

Boost pressure kPa 36 36

Boost pressure mmHg 270 270

Injection quantity adjustment_06

Adjusting point E

Rack position R1+0.7

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 113.5 109.5 117.5

Fixing the lever *

Boost pressure kPa 36 36

Boost pressure mmHg 270 270

Injection quantity adjustment_07

Adjusting point F

Rack position (R2-0.75 )

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 48.2 46.2 50.2

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Boost compensator adjustment

Pump speed r/min 500 500 500

Rack position (R2-0.75 )

Boost pressure kPa 3.3 2 4.6

Boost pressure mmHg 25 15 35

Boost compensator adjustment_02

Pump speed r/min 500 500 500

Rack position R2[R1-0. 4]

Boost pressure kPa 22.7 22.7 22.7

Boost pressure mmHg 170 170 170

Timer adjustment

Pump speed r/min 1150--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1100

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1340

Advance angle deg. 3.5 3 4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL
----------
T1=H52 BCL=(0.75)+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=35mm
----------
a=33deg+-5deg b=42deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Set the stopper bolt at speed = aa and rack position = bb and confirm non-injection. (2)After setting the stopper bolt, confirm non-injection at speed = cc and rack position = dd.
----------
aa=1350r/min bb=7-0.5mm cc=275r/min dd=(8)mm
----------
a=25deg+-5deg b=27deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=400r/min Ra=9.2+-0.1mm
----------

Timing setting

(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=11deg
----------
a=(0deg)

Information:

Introduction
This Special Instruction is intended for the installation of the 366-9748 Injector Wiring Harness Kit . The 366-9748 Injector Wiring Harness Kit can be used to repair TPI connectors. TPI connectors can be found on HEUI injectors, variable valve actuators, and Cat Brakes.Removal of the Connector From the Wire Harness
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9150 Terminal Crimp Tool As 1
B 9U-6070
or Heat Gun Gp
(110V) 1
9U-6072 Heat Gun Gp (220 V) The following steps will remove the connector for an injector from the wire harness that is under the valve mechanism cover.
Illustration 1 g01035448
(1) Side "A" of the connector (2) Side "B" of the connectorNote: Side "A" or side "1" of the connector is the output signal wire from the ECM. Side"B" or side "2" of the connector is the sensor return.
Identify side "A" of the connector and identify side "B" of the connector.
Mark each wire on the wire harness before the wires are cut. Most connectors will have the label of an "A" and a "B". Some connectors may have a "1" and a "2" that is on the connector. The label with a "1" will be an "A". The label with a "2" will be a "B".
Illustration 2 g01034438
Connector that is cut from the wire harness (3) Wire on side "A" of the connector (4) Wire on side "B" of the connector
Cut wire (3) at a distance of 45 mm (1.8 inch).
Cut wire (4) at a distance of 40 mm (1.6 inch).
Illustration 3 g01034450
(5) Wire from the harness for side "B" on the connector (6) Wire from the harness for side "A" on the connectorNote: The wires on the old connector are cut to length so that the wires on the wire harness to the new connector will match up. The proper length will help in matching the harness wires to the wires on the new connector wires.
Discard the connector.Installation Procedure for the Connector
Use Tool (A) to strip the plastic off wires (5) and (6) at a distance of 5 mm (0.19 inch).
Illustration 4 g01034451
Connecting the connector to the wire harness (5) Wire from the harness for side "B" on the connector (6) Wire from the harness for side "A" on the connector (7) Heat shrink tube (8) Butt splice on wire (4) that is on side "B" of the connector (9) Butt splice on wire (3) that is on side "A" of the connector
Use the heat shrink tubes from 366-9748 Injector Wiring Harness Kit . Slide the heat shrink tubes toward the connector in order to expose the butt splices.
Take wire (5) and slide wire (5) in the butt splice (8).
Take wire (6) and slide wire (6) in the butt splice (9).
Illustration 5 g01035814
Illustration 6 g01034452
(8) Butt splice on wire (4) that is on side "B" of the connector (9) Butt splice on wire (3) that is on side "A" of the connector
Use Tool