101607-6081 ZEXEL 9 400 615 669 BOSCH INJECTION-PUMP ASSEMBLY 9400615669 1016076081 me076994

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 615 669 9400615669

ZEXEL 101607-6081 1016076081

MITSUBISHI ME076994 me076994

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101607-6081 zexel genuine, new aftermarket engine parts with delivery

Service parts 101607-6081 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101061-8391

3. GOVERNOR 105931-9331

4. SUPPLY PUMP 105210-4661

5. AUTOM. ADVANCE MECHANIS 105672-5140

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2)

13. NOZZLE-HOLDER

14. NOZZLE

15. NOZZLE SET

Include in #1:

101402-7510 as _

101607-6081 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 615 669 9400615669

ZEXEL 101607-6081 1016076081

MITSUBISHI ME076994 me076994

Zexel num

Bosch num

Firm num

Name

101607-6081

9 400 615 669

ME076994 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D16 K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-8420

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.2 3.15 3.25

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 11.7

Pump speed r/min 850 850 850

Each cylinder's injection qty mm3/st. 77.4 75.1 79.7

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 9.5+-0.5

Pump speed r/min 800 800 800

Each cylinder's injection qty mm3/st. 10.8 9.2 12.4

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(11.7)

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 77.4 76.4 78.4

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.55

Pump speed r/min 1450 1450 1450

Average injection quantity mm3/st. 87.7 83.7 91.7

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1-0.4

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 56 52 60

Fixing the lever *

Injection quantity adjustment_06

Adjusting point E

Rack position (R1+0.5)

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 87.6 83.6 91.6

Fixing the lever *

Injection quantity adjustment_07

Adjusting point I

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 91 81 101

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 1080

Advance angle deg. 0.5

Timer adjustment_02

Pump speed r/min -

Advance angle deg. 2.5 2.5 2.5

Remarks
Measure the actual speed.

Timer adjustment_03

Pump speed r/min 1390

Advance angle deg. 6 5.5 6.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=H50
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=18.5deg+-5deg b=(42deg)+-3deg

Stop lever angle

N:Engine manufacturer's normal use S:Stop the pump. (1)Set the stopper bolt at pump speed = aa and rack position = bb (non-injection rack position). Confirm non-injection. (2)After setting the stopper bolt, confirm non-injection at speed cc. Rack position = dd (non-injection rack position). (3)Rack position = approximately ee. (4)Free (at delivery)
----------
aa=1450r/min bb=7.2-0.5mm cc=275r/min dd=(8.8)mm ee=15mm
----------
a=36.5deg+-5deg b=(25deg) c=13deg+-5deg

0000001501 LEVER

(A) Accelerator lever stopper bolt (B) Link (c) Nut (D) Lever (E) Pin (f) lever (G) Stopper bolt (H) Return spring (J) Pin (E) contacts lever. (K) Load sensor terminal (1)Black (2)Blue-yellow (3)Blue-red Setting the accelerator lever angle, load sensor adjustment 1. Accelerator lever setting method (1)Position the speed lever against the idle stopper bolt and fix. (2)Screw in the accelerator lever stopper bolt (A) and back off the stopper bolt (A) from the position where the accelerator lever pin contacts the speed lever and set. (Gap: approx. 1 mm) Tightening torque: 4.9~7 N.m {0.5~0.7 kgf.m} 2. Load sensor adjustment (See fig 1) (1)Load sensor output measuring circuit Apply DC5+-0.01V to the load sensor terminals and measure the output voltage. (2)Load sensor output adjustment procedure Hold the speed lever against the full side stopper bolt and fix. Adjust the load sensor output voltage to VF = 0.417+-0.1 V using the link (B) and then fix temporarily using nut (C). Turn the speed lever from the idle side to the full side and confirm that output voltage VF = 0.417+-0.1 V is obtained. Confirm several times and then fix using nut (C). Tightening torque: 3.4~4.9 N.m {0.35~0.5 kgf.m} 3. Setting the step motor's idle side stopper bolt After adjustment in previous 1 and 2, position speed lever against idle stopper bolt and fix. Then, screw in stopper bolt G until step motor lever D's pin E contacts lever F. Back off 10+2 deg (approx. 3.5 mm) from this position and fix G. (See fig. 3) 4. Speed lever return confirmation (1)Remove return spring (H) and confirm that the speed lever is returned to the idle position by the torsion spring. (2)Reinstall the return spring (H) in its original position.
----------

----------

Timing setting

(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=10deg
----------
a=(3deg)

Information:

Illustration 40 g00571243
146-9438 Engine Protection Device Change 03
Illustration 41 g00571248
147-2369 Contactor Mounting Change 01
Illustration 42 g00571249
147-2374 Transducer Mounting Group Change 01
Illustration 43 g00571250
147-5676 Instrument Panel Mounting Change 01
Illustration 44 g00571252
148-0165 Instrument Panel Change 01
Illustration 45 g00571273
148-0167 Protection Lines Change 02, Sheet 1 of 3
Illustration 46 g00571274
148-0167 Protection Lines Change 02, Sheet 2 of 3
Illustration 47 g00571278
148-0167 Protection Lines Change 02, Sheet 3 of 3
Illustration 48 g00571279
148-0169 Protection Lines Change 01, Sheet 1 of 2
Illustration 49 g00571281
148-0169 Protection Lines Change 01, Sheet 2 of 2
Illustration 50 g00571283
148-0172 Junction Box Mounting Change 01
Illustration 51 g00571284
148-0200 Transducer Mounting Change 02
Illustration 52 g00571285
148-0204 Instrument Panel Change 00
Illustration 53 g00571287
148-5722 Junction Box Mounting Change 00
Illustration 54 g00571356
157-3242 Contactor Mounting Change 00