Fuel injectors
  1. Home
  2. injection
  3. #1016069300

101606-9300 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016069300


 

Information injection-pump assembly

ZEXEL 101606-9300 1016069300
101606-9300 INJECTION-PUMP ASSEMBLY
Rating:
59
Buy INJECTION-PUMP ASSEMBLY 101606-9300 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

ZEXEL 101606-9300 1016069300


Zexel num
Bosch num
Firm num
Name
101606-9300 
101606-9304 
 
  HYUNDAI
INJECTION-PUMP ASSEMBLY
6D22 *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil   ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm) mm   6-2-600
Overflow valve   131424-5120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right   R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right   R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.5 4.45 4.55
Beginning of injection position
Governor side   NO.1
Difference between angles 1
Cal 1-5 deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3 deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6 deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2 deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4 deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   9.6
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   112 109.2 114.8
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   8+-0.5
Pump speed r/min   225 225 225
Each cylinder's injection qty mm3/st.   18.5 15.7 21.3
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(9.6)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   112 111 113
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(9.6)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   113.5 111 116
Difference in delivery mm3/st.   9 9 9
Fixing the lever   *
Timer adjustment
Pump speed r/min   950--
Advance angle deg.   0 0 0
Remarks
Start  
Timer adjustment_02
Pump speed r/min   900
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1150
Advance angle deg.   4.5 4 5
Remarks
Finish  

Test data Ex:

Governor adjustment

Test data 101606-9300
N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Excess fuel setting for starting: SXL (N = N1) (3)Damper spring setting
----------
SXL=(R1+0.3)+0.2mm N1=350r/min
----------

Speed control lever angle

Test data 101606-9300
F:Full speed
----------

----------
a=6.5deg+-5deg

0000000901

Test data 101606-9300
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=18.5deg+-3deg b=25deg+-5deg

Stop lever angle

Test data 101606-9300
N:Pump normal S:Stop the pump.
----------

----------
a=54deg+-5deg b=71deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325r/min Ra=7.3+-0.1mm
----------

Timing setting

Test data 101606-9300
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=15deg
----------
a=(7deg)




Information:

1. Remove fuel line (1) from the fuel transfer pump.2. Put caps in the fuel line openings to prevent fuel system contamination.3. Remove bolts (2), and remove fuel transfer pump (3). Check the condition of the O-ring seal on the fuel transfer pump. If necessary, make a replacement. The following steps are for installation of the fuel transfer pump.4. Be sure the O-ring seal is in position on the fuel transfer pump. Put clean engine oil on the O-ring seal.5. Put fuel transfer pump (3) in position, and install the bolts that hold it in place.6. Remove the caps from the fuel line openings, and install fuel line (1).Disassemble Fuel Transfer Pump
Start By:a. remove fuel transfer pump 1. Remove seal (1) from the fuel transfer pump.
Cover (2) is under spring tension. Remove the bolts that hold cover (2) slowly to prevent injury.
2. Remove bolts (3) and cover (2) from the housing. 3. Remove seals (4) and valve (5) from cover (2). 4. Remove spring (6) from the piston.
Mark the orientation of valve (8) as to its location in the housing.
5. Remove washer (7), valve (8) and the seal from the housing. 6. Remove piston (9) and sleeve (10) from the housing. 7. Remove seal (11) from sleeve (12). 8. Remove guide and tappet assembly (13) from the housing. 9. Remove seal (14) from guide (15).
If tappet (17) or the guide are damaged or worn, they must be replaced as a unit.
10. Remove ring (16) from tappet (17) and the tappet from guide (15). 11. Remove the bolts and cover (18) from the housing. 12. Remove seal (19) from cover (18). 13. Remove valve (20) from the housing if necessary.Assemble Fuel Transfer Pump
1. Install valve (20) in housing as shown. 2. Put clean fuel on seal (19), and install it on cover (18).3. Install cover (18) on the housing.
The tappet and guide must be serviced as a unit.
4. Install tappet (17) in guide (15). Install ring (16) on tappet (17) to hold the tappet in the guide. 5. Put clean fuel on seal (14), and install it on guide and tappet assembly (13).6. Install guide and tappet assembly (13) in the housing as shown. 7. Put clean fuel on seal (11), and install it on sleeve (12).8. Install sleeve (12) in the housing. 9. Install piston (9) in the housing. 10. Install seal, valve (8) and washer (7) in the housing as shown. Be sure valve (8) is the correct position in the housing. 11. Install spring (6) in the piston. 12. Install valve (5) in cover (2) as shown.13. Put clean fuel on seals (4), and put them in position on cover (2).14. Install cover (2) on the housing. 15. Put seal (1) in position on the fuel transfer pump.16. Install the fuel transfer pump on the fuel injection pump housing.End By:a. install fuel transfer pump

Have questions with 101606-9300?





Group cross 101606-9300 ZEXEL

Hyundai 

101606-9300  

101606-9304 
 
 
INJECTION-PUMP ASSEMBLY
6D22
101606-9301  

101606-9304 
 
 
INJECTION-PUMP ASSEMBLY
6D22
101606-9302  

101606-9304 
 
 
INJECTION-PUMP ASSEMBLY
6D22

Dpico 

101606-9303  

101606-9304 
 
 
INJECTION-PUMP ASSEMBLY
6D22
101606-9304  

106671-9290 
F 019 Z10 994 
 
INJECTION-PUMP ASSEMBLY
6D22
Back to top