Information injection-pump assembly
BOSCH
9 400 615 263
9400615263
ZEXEL
101603-8403
1016038403
ISUZU
8943955723
8943955723
Rating:
Service parts 101603-8403 INJECTION-PUMP ASSEMBLY:
1.
_
7.
COUPLING PLATE
8.
_
9.
_
11.
Nozzle and Holder
12.
Open Pre:MPa(Kqf/cm2)
16.2(165)/18.1(185)
15.
NOZZLE SET
Include in #1:
101603-8403
as INJECTION-PUMP ASSEMBLY
Include in #2:
104749-5190
as _
Cross reference number
Zexel num
Bosch num
Firm num
Name
101603-8403
9 400 615 263
8943955723 ISUZU
INJECTION-PUMP ASSEMBLY
6HH1-S K 14BF INJECTION PUMP ASSY PE6AD PE
6HH1-S K 14BF INJECTION PUMP ASSY PE6AD PE
Information:
start by: a) remove fuel transfer pump 1. Remove nut (3), gear (2) and woodruff key from fuel transfer pump.2. Remove the cage assembly (1) from the pump. 3. Remove the bearing and lip-type seals from cage with tooling (A). 4. Remove cover (5) from pump housing.
Be careful of cover and pump body surfaces that fit together to prevent damage to them.
5. Remove the seal from the cover.6. Remove the gear (4), and shaft assembly (6) from the pump housing. 7. Remove the bearing from pump housing with tooling (A).Assemble Fuel Transfer Pump
1. Install the bearing in the pump housing and the bearing cage with tooling (A). Install inner seal in cage to a depth of .580" (14.73 mm) from face of seal. Install outer seal to a depth of .120" (3.05 mm) to outer face of seal. 2. Install seals (4) in pump housing cover and bearing cage (3) with tooling (B). Install the seals with the spring side of lip in the direction shown.3. Put a thin layer of 8S6747 Permatex Aviation type Form-A-Gasket on the sealing surface of the pump housing.
Do not let Permatex get into pump.
4. Install the gear and shaft assembly in the pump housing. 5. Install the cover (6) and bolts (5) on the pump housing. After bolts (5) are tightened the gear and shaft assembly must turn freely.6. Install the bearing cage on the pump housing.7. Install the woodruff key, gear (2) and nut (1) on the shaft. Tighten nut (1) to 22 5 lb.ft. (29.8 6.8 N m).end by: a) install fuel transfer pump
Be careful of cover and pump body surfaces that fit together to prevent damage to them.
5. Remove the seal from the cover.6. Remove the gear (4), and shaft assembly (6) from the pump housing. 7. Remove the bearing from pump housing with tooling (A).Assemble Fuel Transfer Pump
1. Install the bearing in the pump housing and the bearing cage with tooling (A). Install inner seal in cage to a depth of .580" (14.73 mm) from face of seal. Install outer seal to a depth of .120" (3.05 mm) to outer face of seal. 2. Install seals (4) in pump housing cover and bearing cage (3) with tooling (B). Install the seals with the spring side of lip in the direction shown.3. Put a thin layer of 8S6747 Permatex Aviation type Form-A-Gasket on the sealing surface of the pump housing.
Do not let Permatex get into pump.
4. Install the gear and shaft assembly in the pump housing. 5. Install the cover (6) and bolts (5) on the pump housing. After bolts (5) are tightened the gear and shaft assembly must turn freely.6. Install the bearing cage on the pump housing.7. Install the woodruff key, gear (2) and nut (1) on the shaft. Tighten nut (1) to 22 5 lb.ft. (29.8 6.8 N m).end by: a) install fuel transfer pump
Have questions with 101603-8403?
Group cross 101603-8403 ZEXEL
Isuzu
101603-8403
9 400 615 263
8943955723
INJECTION-PUMP ASSEMBLY
6HH1-S
6HH1-S