101603-4654 ZEXEL 9 400 615 092 BOSCH INJECTION-PUMP ASSEMBLY 9400615092 1016034654 1156022624

Information injection-pump assembly

BOSCH 9 400 615 092 9400615092

ZEXEL 101603-4654 1016034654

ISUZU 1156022624 1156022624

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-4654 zexel genuine, new aftermarket engine parts with delivery

Service parts 101603-4654 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-4600

3. GOVERNOR 105931-5031

4. SUPPLY PUMP 105220-5930

5. AUTOM. ADVANCE MECHANIS 105644-0400

6. COUPLING PLATE 105661-0730

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105118-4521

11. Nozzle and Holder 1-15300-213-1

12. Open Pre:MPa(Kqf/cm2) 18.1{185}

13. NOZZLE-HOLDER 105038-4001

14. NOZZLE

105017-0400

15. NOZZLE SET

Include in #1:

101603-4654 as INJECTION-PUMP ASSEMBLY

Include in #2:

104741-1561 as _

Cross reference number

Zexel num

Bosch num

Firm num

Name

101603-4654

9 400 615 092

1156022624 ISUZU

INJECTION-PUMP ASSEMBLY
6BG1-S * K 14BF INJECTION PUMP ASSY PE6AD PE

Information:

TECHNICAL INFORMATION BULLETIN JAN. 15th, 2003
EXCAVATORS
WHEEL LOADERS
ENGINES 322C: (EMR, MAR);
325C: (CRB, CSJ, JLC, JLD, DTF)
950G II: (AYL, AYB);
962G II: (AYE, BAB)
3126B: (BMA)
Component Code(s) 1408SUBJECT: A NEW INJECTION ACTUATION PRESSURE CONTROL VALVE CONNECTOR INCREASES ENGINE OPERATION
PROBLEM:
The injection actuation pressure (IAP) control valve connector may have been assembled incorrectly on some 3126B engine harnesses. This can lead to intermittent engine operation or can cause the engine to stop.
SOLUTION:
If your machine exhibits symptoms of intermittent engine operation or abruptly stopping, the IAP control valve connector should be disconnected from the machine, examined for solenoid contact problems and re-installed using a correct procedure.
Procedure for installing the IAP control valve connector
This procedure will describe how to properly install the 232-4367 Harness.
Required Parts
Qty Part Number Description
1 232-4367 Harness
Procure the part that is listed in the table.
Illustration 1. Left Side of a 3126B Engine on a D6N.
(1) IAP Control Valve
(2) IAP Control Valve Connector
Note: Illustration 1 is from a D6N that is equipped with a 3126B for photographical purposes. The location of the IAP Control Valve is the same for your machine.
Disconnect the IAP control valve connector (2) from the IAP Control Valve (1). See Illustration 1.
Cut the two wires directly behind the connector.
Using wire strippers, strip the ends of the two wires.
Install the 232-4367 Harness, by crimping the stripped wires inside the splice.
Note: Take care to connect the pink wire to the pink wire on one hand and the purple wire to the purple wire on the other hand.
Heat both heat shrinkable tubes in order to insulate both the splices.
Reconnect the repaired harness to the IAP Control Valve (1).
COPYRIGHT 2003 CATERPILLAR
ALL RIGHTS RESERVED