101603-2791 ZEXEL 9 400 613 368 BOSCH INJECTION-PUMP ASSEMBLY 9400613368 1016032791 220206380b

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 613 368 9400613368

ZEXEL 101603-2791 1016032791

HINO 220206380B 220206380b

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-2791 zexel genuine, new aftermarket engine parts with delivery

Service parts 101603-2791 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-6590

3. GOVERNOR 105419-4670

4. SUPPLY PUMP 105210-6060

5. AUTOM. ADVANCE MECHANIS 105672-5450

6. COUPLING PLATE 105662-1520

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-8384

11. Nozzle and Holder 236003233B

12. Open Pre:MPa(Kqf/cm2) 16.7{170}/21.6{220}

13. NOZZLE-HOLDER 105030-3700

14. NOZZLE

15. NOZZLE SET 105019-2132

Include in #1:

101442-0080 as _

101603-2791 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 613 368 9400613368

ZEXEL 101603-2791 1016032791

HINO 220206380B 220206380b

Zexel num

Bosch num

Firm num

Name

101603-2791
101603-2792

9 400 613 368

220206380B HINO

INJECTION-PUMP ASSEMBLY
J08C * K 14BF PE6AD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131425-0620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.8 3.77 3.83

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point A

Rack position 9.5

Pump speed r/min 1250 1250 1250

Average injection quantity mm3/st. 104.5 102.5 106.5

Max. variation between cylinders % 0 -3.5 3.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point -

Rack position 6.5+-0.5

Pump speed r/min 620 620 620

Average injection quantity mm3/st. 9.5 8.5 10.5

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point D

Rack position 9.7++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 120 120 130

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min (N1+50)- -

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min N1(895)

Advance angle deg. 0.3

Timer adjustment_03

Pump speed r/min (1065)

Advance angle deg. 1.5 1.2 1.8

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Notch fixed: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Rack difference between N = N1 and N = N2 (5)Idle sub spring setting: L1.
----------
K=10 N1=1250r/min N2=600r/min L1=7.9-0.2mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(24deg)+-5deg b=(15deg)+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Normal stop (3)Rack position = bb or less, speed = cc
----------
aa=25mm bb=5.5mm cc=0r/min
----------
a=19deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(20deg)

Information:

Start By:a. remove valve covers 1. Use Tool (A) and disconnect fuel line (1) at each end. Remove the fuel line from the engine. 2. Use Tool (B) and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with Tool (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. Install the 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle (3).4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use Tool (D) and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for the installation of the fuel injection nozzles and adapters.7. Use Tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn Tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and on seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6) and install the adapter in the cylinder head assembly.12. Use Tool (D) and tighten the adapter to a torque of 205 14 N m (150 10 lb ft).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4) and use Tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter and install retainer (2).15. Use Tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb ft).16. Install fuel line (1). Tighten the nuts on the fuel line with Tool (A) to a torque of 40 7 N m (30 5 lb ft).End By:a. install valve covers