101603-2230 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016032230 220009010b

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 101603-2230 1016032230

HINO 220009010B 220009010b

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-2230 zexel genuine, new aftermarket engine parts with delivery

Service parts 101603-2230 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-6171

3. GOVERNOR 105932-1250

4. SUPPLY PUMP 105210-6060

5. AUTOM. ADVANCE MECHANIS 105680-5010

6. COUPLING PLATE 105662-1460

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-7705

11. Nozzle and Holder 23600-2663

12. Open Pre:MPa(Kqf/cm2) 16.7{170}/21.6{220}

13. NOZZLE-HOLDER 105030-3601

14. NOZZLE

15. NOZZLE SET 105019-0314

Include in #1:

101603-2230 as INJECTION-PUMP ASSEMBLY

101603-7474 as _

Cross reference number

ZEXEL 101603-2230 1016032230

HINO 220009010B 220009010b

Zexel num

Bosch num

Firm num

Name

101603-2230
101603-2231

220009010B HINO

INJECTION-PUMP ASSEMBLY
J-2 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131425-0620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.8 3.77 3.83

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point -

Rack position 12.5

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 104.5 102.5 106.5

Max. variation between cylinders % 0 -3.5 3.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 9.5+-0.5

Pump speed r/min 400 400 400

Each cylinder's injection qty mm3/st. 13 12 14

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.5)

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 104.5 103.5 105.5

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.9

Pump speed r/min 1450 1450 1450

Average injection quantity mm3/st. 109.5 105.5 113.5

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1+0.55

Pump speed r/min 1160 1160 1160

Average injection quantity mm3/st. 109 105 113

Fixing the lever *

Injection quantity adjustment_06

Adjusting point I

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 140 140 150

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 950--

Advance angle deg. 0 0 0

Load 1/5

Remarks
Start

Timer adjustment_02

Pump speed r/min 900

Advance angle deg. 0.3

Load 1/5

Timer adjustment_03

Pump speed r/min -

Advance angle deg. 1.25 0.95 1.55

Load 5/5

Remarks
Measure the actual speed.

Timer adjustment_04

Pump speed r/min (1190++)

Advance angle deg. 1.25 0.95 1.55

Load 2/5

Remarks
Measure the actual speed.

Timer adjustment_05

Pump speed r/min 1255-50

Advance angle deg. 1.25 0.95 1.55

Load 5/5

Timer adjustment_06

Pump speed r/min 1420-50

Advance angle deg. 5.5 5.2 5.8

Load 5/5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=K74
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=41mm
----------
a=6deg+-5deg b=(46.5deg)+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Set the stopper screw so that speed = bb and the rack position = cc and confirm non-injection. (3)After setting the stopper bolt, confirm non-injection at speed dd. Rack position = non-injection rack position (actual measurement)
----------
aa=38mm bb=1610r/min cc=6.6-0.5mm dd=300r/min
----------
a=0deg+-5deg b=(26deg)+-5deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(20deg)

Information:

Cylinder Heads Without Guides
Cylinder Heads With Guides New cylinder heads have been introduced on the 4.236 and T4.236 engines. The new heads have replaceable valve guides. The differences between the earlier and current heads are explained below. The change became effective at engine serial number LD or LJ-----U040236M and up. The engine serial number is located above the fuel injection pump on the block.(1) Outer spring: Length under test force ... 27.4 mm (1.08 in)Test force ... 180 9 N (40 2 lb)Free length after test ... 45.2 mm (1.78 in)(Damper coils of spring go toward cylinder head).(2) Inner spring: Length under test force ... 23.88 mm (.940 in)Test force ... 69 9 N (15.4 2 lb)Free length after test ... 39.6 mm (1.56 in)(Damper coils of spring go toward cylinder head).Earlier Cylinder Heads Without Removable Guides
(3) Exhaust valve stem diameter ... 9.449 to 9.469 mm (.372 to .3728 in) Valves are available in stem oversizes of 0.08, 0.38 and 0.76 mm (.003, .015 and .030 in).Exhaust valve overall length ... 123.11 to 123.52 mm (4.847 to 4.863 in)Bore in cylinder head for valve ... 9.506 to 9.531 mm (.37425 to .37525 in)Clearance between valve stem and bore ... 0.0368 to 0.0826 mm (.00145 to .00325 in)Maximum permissible clearance between valve stem and bore ... 0.15 mm (.006 in)(4) Intake valve stem diameter ... 9.462 to 9.487 mm (.3725 to .3735 in) Valves are available in stem oversizes of 0.08, 0.38 and 0.76 mm (.003, .015 and .030 in).Intake valve overall length ... 122.71 to 123.11 mm (4.831 to 4.847 in)Bore in cylinder head for valve ... 9.506 to 9.531 mm (.37425 to .37525 in)Clearance between valve stem and bore ... 0.0191 to 0.0699 mm (.00075 to .00275 in)Maximum permissible clearance between valve stem and bore ... 0.13 mm (.005 in)Current Cylinder Heads With Removable Guides
(5) Valve guides: Inside diameter ... 9.507 to 9.543 mm (.3743 or .3757 in)Outside diameter ... 15.921 to 15.933 mm (.6268 to .6273 in)Parent bore diameter in cylinder head for valve guide ... 15.867 to 15.893 mm (.6247 to .6257 in)Interference fit of guide in cylinder head ... 0.028 to 0.066 mm (.0011 to .0026 in)Overall length of guide: Intake ... 57.94 mm (2.281 in)Exhaust ... 61.11 mm (2.406 in)Projection of guide above valve spring recess ... 15.09 mm (.594 in)(6) Exhaust valve stem: Diameter ... 9.449 to 9.468 mm (.372 to .3728 in)Clearance of valve in guide ... 0.058 to 0.119 mm (.0023 to .0047 in)Maximum permissible clearance of valve in guide ... 0.13 mm (.005 in)Exhaust valve overall length ... 123.11 to 123.52 mm (4.847 to 4.863 in)(7) Intake valve stem: Diameter ... 9.462 to 9.487 mm (.3725 to .3735 in)Clearance of valve in guide ... 0.058 to 0.119 mm (.0023 to .0047 in)Maximum permissible clearance of valve in guide ... 0.13 mm (.006 in)Intake valve overall length ... 122.71 to 123.11 mm (4.831 to 4.847 in)All Cylinder