101603-1921 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016031921

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 101603-1921 1016031921

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-1921 zexel genuine, new aftermarket engine parts with delivery

Service parts 101603-1921 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-9690

3. GOVERNOR 105931-2400

4. SUPPLY PUMP 105210-4700

5. AUTOM. ADVANCE MECHANIS 105643-0070

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-5990

11. Nozzle and Holder ME035748

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105031-3900

14. NOZZLE

105015-5670

15. NOZZLE SET

Include in #1:

101603-1921 as INJECTION-PUMP ASSEMBLY

101603-8140 as _

Cross reference number

ZEXEL 101603-1921 1016031921

Zexel num

Bosch num

Firm num

Name

101603-1921
101606-1112

MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D15 *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-5520

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.6 3.55 3.65

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 11

Pump speed r/min 850 850 850

Each cylinder's injection qty mm3/st. 60 58.1 61.9

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point -

Rack position 10+-0.5

Pump speed r/min 275 275 275

Each cylinder's injection qty mm3/st. 10 8.9 11.1

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point A

Rack position R1(11)

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 60 59 61

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.6

Pump speed r/min 1450 1450 1450

Average injection quantity mm3/st. 80.5 78.5 82.5

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1-0.4

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 42.5 40.5 44.5

Fixing the lever *

Injection quantity adjustment_06

Adjusting point I

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 80 75 85

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 1250--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1200

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1350

Advance angle deg. 2.4 1.9 2.9

Timer adjustment_04

Pump speed r/min 1500

Advance angle deg. 5 4.5 5.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT
----------
T1=A63
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=18.5deg+-5deg b=42deg+-3deg

Stop lever angle

N:Engine manufacturer's normal use S:Stop the pump. (1)At the rated pump speed and rack position aa, set the stopper bolt. (Confirm that there is no injection.) (2)After setting the stopper bolt , confirm non-injection at pump speed bb. Rack position = cc (non-injection rack position). (3)Rack position = approximately dd (4)Free (at shipping)
----------
aa=7mm bb=275r/min cc=(8)mm dd=17.4mm
----------
a=38.5deg+-5deg b=(27deg) c=17deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=400+-5r/min Ra=9.2mm
----------

Timing setting

(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(1deg)

Information:

8C3650 24V (Delco-Remy Number 1993815)
Rotation as seen from drive end ... ClockwiseMinimum speed with no load ... 6300 rpmMaximum speed with no load ... 8400 rpmCurrent consumption (draw) at no load: Minimum with solenoid at 23V ... 60AMaximum with solenoid at 23V ... 75AClearance between pinion and housing (pinion clearance) ... 9.1 mm (.36 in)(1) Torque for terminal nuts ... 27 to 34 N m (20 to 25 lb ft)(2) Torque for screws holding nose housing to lever housing ... 23.7 6.1 N m (17 4.5 lb ft)8C3651 24V (Delco-Remy Number 1993804)
Rotation as seen from drive end ... ClockwiseMinimum speed with no load ... 6300 rpmMaximum speed with no load ... 8400 rpmCurrent consumption (draw) at no load: Minimum with solenoid at 23V ... 60AMaximum with solenoid at 23V ... 75AClearance between pinion and housing (pinion clearance) ... 9.1 mm (.36 in)(1) Torque for terminal nuts ... 27 to 34 N m (20 to 25 lb ft)(2) Torque for screws holding nose housing to lever housing ... 23.7 6.1 N m (17 4.5 lb ft)3T2647 24V (Delco-Remy Number 1114845)
Rotation as seen from drive end ... ClockwiseMinimum speed with no load ... 6000 rpmMaximum speed with no load ... 10260 rpmCurrent consumption (draw) at no load: Minimum with solenoid at 23V ... 60AMaximum with solenoid at 23V ... 118AClearance between pinion and housing (pinion clearance) ... 8.3 to 9.9 mm (.33 to .39 in)(1) Torque for terminal nuts ... 27 to 34 N m (20 to 25 lb ft)3T2772 24V (Delco-Remy Number 1113540)
Rotation as seen from drive end ... ClockwiseMinimum speed with no load ... 6850 rpmMaximum speed with no load ... 11250 rpmCurrent consumption (draw) at no load: Minimum with solenoid at 23V ... 48AMaximum with solenoid at 23V ... 76AClearance between pinion and housing (pinion clearance) ... 8.3 to 9.9 mm (.33 to .39 in)(1) Torque for terminal nuts ... 27 to 34 N m (20 to 25 lb ft)3T4581 24V (Delco-Remy Number 1113583)
Rotation as seen from drive end ... ClockwiseMinimum speed with no load ... 7000 rpmMaximum speed with no load ... 11000 rpmCurrent consumption (draw) at no load: Minimum with solenoid at 23V ... 47AMaximum with solenoid at 23V ... 73AClearance between pinion and housing (pinion clearance) ... 8.3 to 9.9 mm (.33 to .39 in)(1) Torque for terminal nuts ... 27 to 34 N m (20 to 25 lb ft)(2) Torque for screws that hold nose housing to lever housing ... 20.3 2.7 N m (15.0 2.0 lb ft)Prestolite Starter Motors
9G4338 24V (Prestolite Number MES6601K)
Rotation as seen