Information injection-pump assembly
BOSCH
9 400 610 618
9400610618
ZEXEL
101602-8260
1016028260
ISUZU
1156031060
1156031060
Rating:
Service parts 101602-8260 INJECTION-PUMP ASSEMBLY:
1.
_
5.
AUTOM. ADVANCE MECHANIS
6.
COUPLING PLATE
8.
_
9.
_
11.
Nozzle and Holder
5-15300-089-1
12.
Open Pre:MPa(Kqf/cm2)
18.1{185}
15.
NOZZLE SET
Cross reference number
Zexel num
Bosch num
Firm num
Name
101602-8260
9 400 610 618
1156031060 ISUZU
INJECTION-PUMP ASSEMBLY
6BD1 K 14BE INJECTION PUMP ASSY PE6A PE
6BD1 K 14BE INJECTION PUMP ASSY PE6A PE
Information:
This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS5560" as the Part Number and "7755" as the Group Number. Use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code.
Termination Date
December 19, 1999Problem
The connection plate from the fuel injection pump lever may wear prematurely causing the return spring to disconnect on certain 312 Excavators. When the return spring disconnects, the fuel injection pump will no longer operate properly.
Affected Product
Model & Identification Number
312 (6BL112-1827)
CIPI Product (05A10771, 10798, 11808)
Parts Needed
1 - 5C2890 Nut1 - 8C3111 Rod End1 - 8T4971 Bolt1 - 9X8256 Washer1 - 1643187 PlateAction Required
See the attached Rework Procedures.
Service Claim Allowances
This is a 1-hour job.
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Attach.(1-Rework Procedure)Rework Procedure
1. Disconnect return spring from 1190312 Plate.2. Remove the ball-joint from extremity of the governor cable, and replace it by 8C3111 Rod End.3. Remove 1190312 Plate, 9X8256 Washer and 8T4134 Nut. Keep 9X8256 Washer to be reused.4. To connect new 1643187 Plate together with injection pump lever and 8C3111 Cable Rod End, use 8T4971 Bolt, (2) 9X8256 Washers and 5C2890 Nut. See Illustration 1.5. Reconnect the return spring to 1643187 Plate.6. Perform an auto calibration through controller Service Mode, and readjust if necessary the cable tension, according to Hydraulics and Electronics "Testing & Adjusting" manual.
Illustration 1
Termination Date
December 19, 1999Problem
The connection plate from the fuel injection pump lever may wear prematurely causing the return spring to disconnect on certain 312 Excavators. When the return spring disconnects, the fuel injection pump will no longer operate properly.
Affected Product
Model & Identification Number
312 (6BL112-1827)
CIPI Product (05A10771, 10798, 11808)
Parts Needed
1 - 5C2890 Nut1 - 8C3111 Rod End1 - 8T4971 Bolt1 - 9X8256 Washer1 - 1643187 PlateAction Required
See the attached Rework Procedures.
Service Claim Allowances
This is a 1-hour job.
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Attach.(1-Rework Procedure)Rework Procedure
1. Disconnect return spring from 1190312 Plate.2. Remove the ball-joint from extremity of the governor cable, and replace it by 8C3111 Rod End.3. Remove 1190312 Plate, 9X8256 Washer and 8T4134 Nut. Keep 9X8256 Washer to be reused.4. To connect new 1643187 Plate together with injection pump lever and 8C3111 Cable Rod End, use 8T4971 Bolt, (2) 9X8256 Washers and 5C2890 Nut. See Illustration 1.5. Reconnect the return spring to 1643187 Plate.6. Perform an auto calibration through controller Service Mode, and readjust if necessary the cable tension, according to Hydraulics and Electronics "Testing & Adjusting" manual.
Illustration 1
Have questions with 101602-8260?
Group cross 101602-8260 ZEXEL
Isuzu
101602-8260
9 400 610 618
1156031060
INJECTION-PUMP ASSEMBLY
6BD1
6BD1